2013 AUDI A5 COUPE lock

was manufacture d. Please see ¢ page 243,
Speed rating (letter code) for a listing of the
speed rat ing letter codes and t he maxim um
speed at whic h the tires can be driven .
The s peed rating letter code(¢
page 233) is
on the side wall of the tire
c::> page 242 .
A WARNING
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed. Always know the maximum
speed before driving off . Never drive faster
than the speed permitted for your specific
w inte r tir es . This will cause damag e to the
ti res leading to an ac cident and serious
pe rsonal in jury to you and yo ur passen­
gers .
A WARNING
Driv ing faster than the maximum speed
for which the winter tires on your vehicle
were designed can ca use tire fai lure in­
cl uding a blowout and sudden deflat ion,
loss of control, crashes and serious per­
sonal injuries . Have worn or damaged tires
rep laced immed iate ly.
- Winter tires have maximum speed rat ing
that may be lower tha n your veh icle's
maximum speed .
- Never drive faster than the speed for
w hich the winter or other tires installed
on your veh icle are rated .
A WARNING
Always adjust your d rivi ng to the road and
traffic conditions. Neve r let the good ac­
c eleration of the w inte r ti res and all whee l
drive temp t you in to taking extra r is k s . A l­
ways remember:
- When bra king, an a ll whee l dr ive vehicle
hand les in the s ame way as a front drive
vehicle.
- Drive carefu lly and reduce your speed on
icy and slippery roads, even winter tires
cannot he lp un der blac k ice conditions.
Tire s an d wheel s 24 7
'
@) For the sake of the environment
Use summer tires when weather condi­
tions permit. They are qu ieter, do not wear
as quickly and reduce fuel consumpt ion.
Snow chains
Snow cha ins may be fitted only to the front
whee ls, and o nly to certain tire sizes . Ask your
autho rized Aud i deale r on which tire sizes
snow c ha ins can be used.
The snow chains must have low-prof ile links
and must not be t hicker than 0.53 inch
(13.5 mm) , includ ing the lock .
Remove wheel center covers and trim discs
before putt ing snow cha ins on your vehicle
c::> Q) . For safety reasons cover caps must then
be fitted over the wheel bolts. These are ava il­
able from autho riz ed Aud i dealers.
A WARNING
Using the wrong snow chai ns for your vehi­
cle o r insta lling them in co rr ect ly can in­
crease the risk of loss of cont ro l leading to
serious pe rsonal injury.
- Snow chains are available in different
sizes. A lways make sure to follow t he i n­
structions p rov ided by the snow chain
manufacturer.
- When driving with snow chains never
drive faster than the speed permitted for
your specif ic snow chains.
- Always observe local regulations .
(D Note
-Remove s now c hain s be fo re dr iv ing o n
roads not covered with snow to avoid
damaging tires and wea ring the snow
chains down unnecessa rily.
- Snow chains, which come into direc t con ­
tact with the whee l rim , can scratch or
damage it . Therefo re, make sure that the
snow chains are s uitably covered. Check
the pos ition of the snow chains after
•
•

252 What do I do n ow ?
What do I do now?
Vehicle tool kit
The tools ore stored underneath the floor
panel in the luggage comportment.
Fig. 182 Luggage compartment: tool kit
When you need access to the vehicle too l kit
or jack*, you will need to take out the spare
tire* and cover ¢
page 252.
The vehicle tool kit includes:
- Hook for removing wheel covers*
- Alignment pin for changing the whee l
- Screwdriver w ith reversible blade
- T ool for chang ing ligh t bu lbs
- Reversible bit (reversible Torx bit for chang-
ing light b ulbs)
- Rod for jack
- Jack*
- Lug wrench
- Towing eye
Some o f the ve hicl e items listed above a re
p rovided on certain models o nly or are option­
a l extras.
Before returning the jack* to its place, retra ct
the jack a rm fully .
_&. WARNING
- Never use the screw driver hex head to
tighten whee l bolts, s ince the bolts can ­
not attain the necessa ry tightening tor­
que i f you use the hex head, potentially
causing an accident.
- The factory -supplied jack is intended on­
ly for your veh icle model. Under no cir­
c u mstances should it be used to lift heavy vehicles or othe
r loads; yo u risk in­
juring yo urself .
- Never start the engine when the vehicle
is raised, wh ich could cause an acc ident.
- Support the vehicle securely wit h app ro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potentia l risk for injury.
Space-saving spare tire
(compact spare tire)
App lies to vehicles: wit h space-saving spare t ire
The spore tire/wheel is located in the luggage
compartmen t under the cargo floor cover. It
is intended for short-term use only.
F ig . 1 83 Spa re tire
Removing the spare t ire
.. Lift t he cargo floor by the p lastic handle
¢fig . 183.
.. Hook the handle into the luggage compart­
ment weather strip.
.. Turn the large screw ¢
fig. 183 counter­
clockw ise .
.. Take out the spare tire .
.. Always store the vehicl e tool kit, the jack*,
and the rep laced tire in the luggage com­
pa rtment
¢page 130.
.. Unhook the cargo floor be fo re closing the
rea r lid.
Using the spare tire (compact spare tire)
T he compact spare ti re is only inte nded for
eme rgen cies unt il you can reach a rep air shop.
Repl ace it as quickly as possible with a stand­
ard wheel and tire.
T he re a re some restr ictions on the use of the
c ompac t spa re tire. The compact spa re tire ...

254 What do I do now?
-To help prevent the vehicle from moving
sudden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed with the fold­ ing chocks or other objects. When one
front whee l is lifted off the gro und, plac ­
ing the A utomat ic Transm iss io n in "P"
(Park) will
not prevent the vehi cle from
moving .
- Be fore yo u change a wheel, be sure the
ground is leve l and fi rm . If necessa ry,
use a sturdy board under the jack.
- After installing the spare tire, make sure
that you replace the f lat ti re/wheel in its
storage area properly and tighten the
knurled retain ing screw secu rely .
@ Note
If you are chang ing the wheel on a steep
incline, use a rock or similar object to
block the opposite wheel to prevent the
veh icle from mov ing.
(D} Tips
Obey a ll laws .
Changing a wheel
When you change a wheel, follow the se­
quence described below step -by -step and in
exactly that order.
1. Remove the decorative wheel c ove r* or
the wheel bolt cap s*. For more de tails see
a lso
¢ page 255, Decorative wheel cov ­
ers
or ¢ page 255, Wheels with wheel
bolt caps.
2 . Loosen the wheel bolts ¢ page 255.
3. Locate the proper mount ing point for the
jack and align the jack below that point
¢ page 256.
4. Lift the car with the jack¢ page 256 .
S. Remove the wheel with th e flat tire and
then install the spare tire
¢page 257.
6. Tighten all wheel bo lts ligh tly.
7 . lowe r the ve hicle w ith the jack . 8
. Use the wheel bolt w rench and firmly
tighten all wheel bolts in a crisscross pat­
te rn
¢ page 255.
9. Replace the decorati ve wheel cover * or
the wheel bolt caps *.
A WARNING
Always read and fo llow all WARNINGS and
in fo rmat ion¢ .&.
in Raising the vehicle on
page 256
and ¢ page 258.
After changing a wheel
A wheel change is not complete without the
doing the following .
.,. Always store the vehicle tool kit, the jack*,
and the replaced tire in the luggage com­
partme nt
¢ page 130.
.,. Check the tire pressure of the spare tire as
soon as possible.
.,. As soon as poss ib le, have the tightening
torque s on all whee l bolts chec ked w ith a
to rque wrenc h. The co rrect tighte ning tor ­
que is
90 ft lbs. (120 Nm) .
.,. Have the flat tire replaced as soon as possi­
ble.
@ Tips
- If you notice that the wheel bo lts a re
co rroded and difficult to turn while
chang ing a tire, they shou ld be rep laced
before you check the tightening torque.
- Dr ive at reduced speed until you have the
tightening torques checked.

-Do not raise the vehicle until yo u are
sure the jack is securely engaged.
- Passenge rs must not remai n in the
ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then contin ue to
ra ise the jack.
CD Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for
changing the wheel.
Fi g. 189 Changing a wheel: using the screwdrive r han ­
dle (with the blade removed) to turn the bolts
Fig . 1 90 Changing a wheel: alignm en t pin ins ide t he
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
What do I d o now ? 257
Removing the wheel
.,. Remove the topmost whee l bolt completely
with the
he xagonal so ck et in the screwdriv ­
er handle (vehicle tool kit)
o fig. 189 and
set it aside on a
clean surface .
.,. Screw the threaded end of the
alignment
pin from the tool kit hand-t ight into the
empty bolt hole
o fig. 190.
.,. Then remove the other wheel bolts as de ­
scribed above .
.,. Take
off the whee l leav ing the a lignment
pi n in the bolt hole
o(D .
Putting on the inflat able spar e tire
.,. Push the spare tire over the alignment p in.
.,. Screw on the wheel bo lts and tighten them
slightly us ing the hexagonal socket .
• Remove the a lignment pin and inse rt and
tighten the rema ining wheel bolt slightly
like the res t.
.,. Turn the jack hand le co unter -clockwise to
lower the veh icle until the jack is fully re ­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts f irm ly
o page 255 . Tighten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
• Perfo rm the steps required afte r changing
the wheel
o page 254, After changing a
wheel.
T he hexagonal socket makes it easie r to re­
move th e wheel bo lts from the rim. Care
sho uld be taken when remov ing the reversib le
blade .
CD Note
When removi ng or insta lling the whee l,
the r im cou ld hit the bra ke roto r and dam­
age the roto r. Work carefu lly and have a
second person to help you .
(l} Tips
-When mount ing tires w ith unidir ectional
tread de sign
make sure the tread pat ­
tern is pointed the right way
o page258. II>-

260 Fuses and bulb s
No.
5 Sound actuator/exhaust sound
tuning
6 Headlight range control sys­
tem/cornering light
7
8
Headlight (corner ing light)
Control modules (electrome­
chanical parking brake, shock
absorber, quattro sport, trailer
hitch), DCDC converter
9 Adaptive cruise contro l
10 Shift gate
1 1 Side ass ist
Headlight range control, park­
ing system
13 Airbag
14 Rear wiper (allroad)
15 Auxiliary fuse (instrument pan­
el)
1
16
Auxiliary fuse terminal 15 (en­
gine area)
Fu se pane l @ (b row n)
2 Brake light sensor
5
6
7
Left seat heating with/w ithout
seat venti lation
ESC Horn
Front left door (window regula-
8 tor, central locking, mirror, switch, lighting)
9 Wiper motor
10 ESC Two-door models: rear left win ­
dow regulator, Fo ur-door mod-
11 els: rear left door (window regu­ lator, central locking, switch,
lighting)
12 Rain and light sensor
F u se p anel© (red )
3
4 Dynamic steer ing
Amps
5/15
5/7,5 7,5
5
5
5
5
5
5
15
10
40
5
25
15/30
5
15
30
30
25
30
-No . Consumer Amps
6
Windshield washer system,
35
headlight washer system
7
Vehicle e lectrical system control
20
module 1
8
Vehicle electrical system control
30
module 1
9 Sunroof 20
10 Vehicle electrical system control
30
module
1
11 Sun shade motor 20
-
12 Anti-theft alarm warning sys-
tern 5
Right cockpit fuse assignment
Fig.
193 Right cockpit : fuse panel wit h plastic cl ip
No. Consume r
Fuse pane l@ (black )
..
5 Steering column switch module
7
8
Terminal 15 diagnostic connec­
tor
Gateway (Databus diagnostic interface)
9 supp lementary heater
Fuse pan el@ (bro wn)
1 CD/DVD player
Amp s
5
5
5
5
5
•
I

-No. Consumer
2 Wi-Fi
3 MMI/Radio
4 Instrument cluster
Gateway (inst
rument cluster
5 control module)
6 Ignition lock
7 L ight switch
8 Climate control system blower
9 Steering col umn lock
10 Climate control system
11 T
ermina l 30 diagnostic connec-
tor
Steering column switch module
Right luggage compartment fuse
assignment Amps
5
5/20
5
5
5
5
40
5
10
10
5
Fig . 194 Right l uggage compart ment : fuse panel with
plastic d ip
No . Con sumer Amps
Fuse panel @ (black )
1 Luggage compar
tment lid con-
30
trol module (allroad)
2
Trailer control module or re-
15
tractable rear spoiler (RS 5)
3 Tra iler control module 20
Fu se s and bulb s 261
No. Consumer
4 Trailer control module
Electromechanical parking
5 5
brake
6 Electronic damping control
15
Electromechanical parking
7 30
brake
8 Rear exterior lighting 30
9 Quattro sport 35
10 Rear exterior lighting 30
11 Vehicle electrical system control
20
module
12 Te rm inal 30
s
Fuse panel © (brown)
1 L
uggage compartmen t lid con-
30
trol module (all ro ad)
2 12-volt socket, cigarette lighter
20
3 DCDC converte r pa th 1 40
4 DCDC converter path 2, DSP
30
amplifier, radio
7 E
lect romechanical parking
30
b rake
Right front door (window regu-
9 lator, cent ral locking, mir ro r, 30
switch, lighting)
Two-door models: rear right
window regu lator, Four-door
1 1 models : rea r right door (window
30
regulator, central locking,
sw itch, lighting)
Cell phone prep
5
Fu se panel © (black )
1 Right front seat heating
15
4 MMI 7,5
5 Radio
5
6 Rear view c amer a 5
7 Rear window heater (allroad)
30
8 Rear Seat Enter tainmen t 5

-Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Do not bend over the batteries - danger
of chemical burns!
- The battery ce ll locking screws must be
tightened securely .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 209, Engine com­
partment .
(D Note
Improper hook -up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that a ll screw plugs on the battery
cells are screwed in firmly. If not, tighten plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies spec ifically to the case of
your vehicle be ing jump started . When
you are giving a jump start to anothe r ve­
hicle, do
not connect the negat ive( -) ca­
ble to the negative( -) terminal on the
discharged battery@¢
fig. 196. In ­
stead, securely connect the negative(-)
cable to either a solid metal component
that is firmly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and exp lode!
Em erg en cy si tuation s 265
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
- Nev er t ow your Audi , tow ing will c aus e
damage t o the engin e and transmi ssion.
- Nev er wrap th e safety chain s or winch c a­
ble s around th e bra ke lines.
- To pre ve nt unne cessary dam ag e, your Aud i
mu st be tra ns po rted wi th a flat bed tru ck .
- To load th e vehicle on to th e flat be d, use
the t owing l oop found in the vehicl e too ls
a nd atta ch to th e front or rear anch o rage
c::> page 266 and ¢page 266 .
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
-
•
•

268 Emergency situations
fall from a lift if there is a change in ve­
hicle weight distribution and balance.
This might happen, for example, when
heavy components such as the engine
block or transmission are removed .
- When removing heavy components like
these, anchor vehicle to hoist or add cor­
responding weights to maintain the cen­
ter of gravity. Otherwise, the vehicle
might tilt or slip off the hoist, causing
serious personal injury.
(D Note
- Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.