2012 SSANGYONG RODIUS height

02-4
2. CHASSIS I
4012-01 Front Sub Frame
- Changed sub frame
4420-01 Front Stabilizer
- Improved rolling capacity
Newly Installed Equipment
2412-02CDPF (Catalyst & Diesel
Particulate Filter)
- Installed CDPF according to Euro 5
regulation
Sub frame bushing
Engine side
Mounting
bracket
assembly
Stabilizer linkStabilizer bar
Stabilizer bar
Mounting
bracket
assembly
Stabilizer link
Changed stabilizer mounting
Changed front axle mounting height

02-30000-00
Cylinder block Piston protrusion 0.475 to 0.745mm -
Piston ring TOP ring end gap 0.20 to 0.35 mm -
2nd ring end gap 0.35 to 0.50 mm -
3rd ring end gap 0.2 to 0.40 mm -
Offset 0.3mm -
Head gasket Piston protrusion 0.475 to 0.540 1.2t -
0.541 to 0.649 1.3t -
0.650 to 0.745 1.4t -
1. ENGINE ASSEMBLY
Unit Description Specification Remark
Cylinder head Height 131.9 to 132.1 mm -
Flatness below 0.1 mm -
Valve protrusion Intake valve 0.6 to 1.0 mm -
Exhaust valve 0.6 to 1.0 mm -
Flatness on
manifold sideIntake manifold 0.08 mm -
Exhaust manifold 0.08 mm -
Connecting rod End play 0.5 to 0.31 mm -
Camshaft Axial end play Intake 0.1 to 0.35 mm -
Exhaust 0.1 to 0.35 mm -
Camshaft
position sensorDistance between Camshaft position
sensor and sprocket0.20 to 1.80 mm -

02-10
2) Cylinder Head
(1) Cylinder head mating surface check
Specified value ▶
Measure the cylinder head height "A". 1.
Insert the valves into the valve guides and
measure the recesses. 2.
Valve recess “a”0.6 to 1.0mm
(2) Cylinder head pressure Leak test
Immerse the cylinder head with the pressure plate into warm water (approx. 60°C) and pressurize
with compressed air to 2 bar.If the height is less than the limit, the
cylinder head must be replaced. -
If the measured value is out of the
specified range, machine the valve seat
as much as necessary until the specified
value is achieved. -
Total height "A"131.9 to 132.1 mm
Minimum height after machining131.9 mm
Flatness Longitudinal direction0.1 / 150
Transverse direction0.15
Parallel deviation of cylinder headbelow 0.1 mm
Peak-to valley of surfaceRmax 7 Rz 6.3
valve recess "a" Intake valve0.6 to 1.0 mm
Exhaust valve0.6 to 1.0 mm

09-58790-01
2. CAUTIONS
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while
washing, since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is
moved into "R" position with the ignition key "ON".
If the system is defective, the warning buzzer sounds for 3 seconds when moving the gear
<009a008f0090008d009b00470093008c009d008c00990047009b0096004702c8007902c9004700970096009a0090009b0090009600950047009e0090009b008f0047009b008f008c00470090008e00950090009b0090009600950047007600750055004700
69008c0047008a00880099008c008d009c0093004700950096>t to confuse this and the parking
aid alarm (in 50 cm). 1.
2.
3.
4.
5.
· Note that the display does not show everything in the rear area. Always check
nobody, especially animals and children, is behind the vehicle when parking or
reversing.
· If you can not properly check the vehicle behind, get out of the vehicle and then
visually check it.
The parking aid system will not work or improperly work under following cases: ▶
1) Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2) Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally
after cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on -
-
-
-
3) Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after cleaned)
<007a009c009900990096009c0095008b00900095008e0047009b008c00940097008c00990088009b009c0099008c00470096008d0047009a008c0095009a0096009900470090009a0047009b009600960047008f0090008e008f0047004f00880097009700
990096009f005500470096009d008c00990047005f005700b6>C) or too low
(approx. below -30°C) -
-
4) Not defective but may cause malfunction
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy
commercial vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
-

10-38910-05
1. SPECIFICATION
Audio Voltage DC 14.4V
Operating voltage DC 10.8V~16.0V
Output45W/ch (Speaker 4Ω)
Speaker Impedance4Ω
Radio
Radio
Radio주파수EUFM: 87.5~108MHz
AM: 531~1602KHz
프리셋FM1: 6ch
FM : 87.5 ~ 108 MHz
AM : 520SS ~ 1620 MHzFM : 87FM : 87.5 ~
108 MHz
AM : 520 ~ 1620 MHz.5 ~ 108 MHz
AM : 520 ~ 1620 MHzFM : 87.5 ~ 108 MHz
AM : 520 ~ 1620 MHzFM2: 6ch
AM: 6ch 사용감도FM : 87.5 ~ 108
MHz
AM : 520 ~ 1620 MHzFM : 87.5 ~ 108 MHz
AM : 520 ~ 1620 MHzAM: 25dBu
FM: 10dBu
S/N비 (한계값)AM: 54dB
FM: 60dB
LCD 형식ISTN
작동전압9.0V VDD: 3.0~3.3V
작동온도 -30℃ ~ +80℃
저장온도 ISTN-40℃ ~ +85℃
규격(너비x높이)132X36
Bluetooth구성요소 M-30℃ ~ +75℃D-5XR (블루투스 멀티미디어
모듈)
적용기술 블루투스 2.0+EDR
(Enhanced Data Rate:
향상된 데이터 속도)
Current consumption below 5A, max. 10A
Dark current below 3mA
Unit Description Specification
안테나안테나 글래스 안테나 내장형
RadioFrequency EU FM : 87.5 ~ 108MHz
MW: 522 ~ 1620 KHz
LW : 144 ~ 290 KHz
Latin
AmericaFM : 87.5 ~ 108 MHz
AM : 520 ~ 1620 MHz
PresetFM1: 6ch
FM2: 6ch
MW: 6ch
LW: 6ch
AM: 6ch
SensitivityAM: 25dBu
FM: 10dBu
S/N ratio (limit)AM: 54dB
FM: 60dB
LCDType ISTN
Operating voltage 9.0V VDD: 3.0~3.3V
Operating temperature-30℃ ~ +80℃
Storage temperature-40℃ ~ +85℃
Size (width x height) 32X36
BluetoothComposition MD-5XR
Technology Bluetooth 2.0 + EDR
Product name HFP A2DP AVRCP
Antenna Glass antenna type

03-33010-00
1. SPECIFICATION
Description Specification
Operating type Hydraulic type
Clutch pedal Type Suspended type
Max. operating travel150 ± 3mm
Pedal height95.2 ± 3mm
Pedal free play 5~15 mm
Clutch disc Type Dry type single diaphragm
Diameter of facingOuter: Ø250 mm
Inner: Ø160 mm
Numbers of disc 2
Thickness of discFree: 8.7 ± 0.3 mm
When loaded: 8.0 ± 0.2 mm
Setting load of clutch cover assembly At least 7,800 N
Clutch master
cylinderOperating travel 33.0mm
Inner diameterØ 15.87
Concentric slave
cylinderMaximum operating travel Max. 20 mm
Operating pressure Max. 2,200 N
Clutch fluid Type DOT 3 or DOT 4
Capacity As required

03-53010-00
3. INSPECTION
Pedal stroke and height ▶
Pedal stroke (A) A.
Stop the engine.
Measure the current pedal position.
Depress the clutch pedal all the way and
measure the pedal stroke (A). 1)
2)
3)
Stroke (A)150 ± 3mm
Pedal height (B) B.
Stop the engine.
Remove the floor mat from the driver’s
footwall.
Measure the pedal height (B). 1)
2)
3)
Height (B)95.2 ± 3mm
Adjustment -
Release the lock nut (D) on stopper bolt (C).
Turn the stopper bolt to adjust the pedal
height.
Tighten the lock nut to the specified
tightening torque. 1)
2)
3)

06-53310-01
1. OVERVIEW
The propeller shaft transfers the power through the transmission and transfer case to the
front/rear axle differential carrier (final reduction gear). It is manufactured by a thin rounded steel
pipe to have the strong resisting force against the torsion and bending. Both ends of propeller
shaft are connected to the spider and the center of propeller shaft is connected to the spline to
accommodate the changes of the height and length. The rubber bushing that covers the
intermediate bearing keeps the balance of rear propeller shaft and absorbs its vibration.
Function of propeller shaft ▶
Transmits driving torque.
Compensates the angle change (universal joint / CV joint).
Compensates the axial length change (splines for the slip joint). -
-
-
4WD AT 2WD MT