2012 SSANGYONG NEW REXTON engine

1725-12
Throttle bodies by engine type
The throttle valve is controlled by electric signals sent from the engine ECU for optimal
fuel injection volume, engine load and effective combustion of EGR gas according to
the Euro 4 regulations. It has following functions by the engine type. -

3. SOOT FILTERING AND BURNING PROCEDURES
1) Operating Procedures of CDPF
The most efficient and practical technology for now is adopted to the diesel particulate filter
(DPF).
This system collects the soot from the diesel engine to the filter and burns the soot so that over
than 95% of soot can be removed from the exhaust gas. However, the durability and the cost of
additional system remain as problems.
Firstly, the exhaust gas is passed through the DOC and its temperature is increased as it is
oxidized. The ECU detects the temperature change with two temperature sensors. The CO, HC
and partial particulate material are removed from the exhaust gas (this procedures are the sames
as the ones for the conventional DOC and no sensor is required).
After the exhaust gas is passed through the DOC and oxidized, most of the harmful material is
removed from the exhaust gas. However, to meet the environmental regulations in the future, the
soot is filtered and burnt again in DPF to decrease the particulate material further.
Rear exhaust gas temperature sensor
(Measuring temperature of exhaust gas
escaping DOC)
The filtered soot is burned whenever the vehicle is driven for 600 ~ 1200 km. The driving
distance can be differed depending on the vehicle's driving conditions. The soot is burnt
for 15 ~ 20 minutes. -

1725-12
Front temperature sensor
(Measuring the temperature of
exhaust gas passed through
exhaust manifold)
Differrential pressure sensor (Front
pressure port) Differrential pressure sensor (Rear
pressure port) Rear temperature sensor
(Measuring the temperature of exhaust gas
passed through DOC)
The exhaust gas enters
into CDPF assembly after
passing through the
exhaust manifold.
(Normal temperature of
exhaust gas: approx. The engine ECU detects
the amount of particulate
material colected by the
information from
temperature sensors and
differential pressure snesor.
When the soot is
accumulated, the pressure
difference between the
front and the rear side
occurs. Then, the engine
ECU performs the post
injection to raise the
exhaust gas temperature
and burn the collected soot
at approx. When the exhaust gas
enters into the CDP
F
assembly, its CO, HC and
particulate material are
reduced as it is oxidized in
DOC. The remaining
particulate material is
filtered and collected in
DPF and the temperature
of exhaust gas is
increased to approx. 450
~

2) Fuel Injection During CDPF Regeneration
3) Warning Lamp Related To CDPF
The CDPF system enters the regeneration mode when
the driving distance becomes approx. 600 to 1,200 km
(may differ by the driving condition and driving style).
Then, the engine ECU performs the CDPF regeneration
operation. However, the driver is not informed with this
operation by any engine warning lamp or vehicle
signal, so he/she may not detect this operation. The
control logic at the post-injection during the
regeneration process is to increase the fuel injection
volume and control the intake air volume (by the throttle
body) in order to increase the temperature of the
exhaust gas. The driver may not feel any particular
difference from the vehicle.
No illuminating

1725-12
If the CDPF cannot reach the regeneration
temperature due to low speed driving or other
reason during the regeneration process, the soot
is continuously accumulated in the CDPF. When
this condition continues and the CDPF is
overloaded with soot, the engine warning lamp
blinks to inform this situation to the driver.
In order to solve this problem, drive the vehicle at
a speed of approx. 80 km/h for 15 to 20 minutes
to perform the CDPF regeneration process.
If the engine warning lamp on the instrument
cluster blinks, the CDPF is overloaded. In this
case, perform the step 2. 1.
2.
3.
If the vehicle is driven at a speed of 5 to 10 km/h
for an extended period of time, the soot
accumulated in the CDPF cannot be burnt as the
CDPF cannot reach the regeneration temperature.
Then, an excessive amount of soot can be
accumulated in the CDPF.
This case is much worse than the simple overload
of the CDPF. To inform this to the driver, the
engine warning lamp comes on and the engine
power is decreased to protect the system.
To solve this problem, blow soot between the
engine and exhaust system several times and
erase the related DTC. Then, check if the same
DTC is regenerated again. If so, check the DTC
related to the differential pressure sensor. 1.
2.
3.
Actually, the DTC for the CDPF is generated more often by the component related to the CDP
F
system, such as the differential pressure sensor, than by excessive soot in the CDPF.
Illuminating
Blinking

4. COMPONENTS OF CDPF SYSTEM
Engine compartment
(RH)
Differential Pressure Sensor
Front Exhaust Gas
Temperature SensorThrottle Body
Front exhaust gas
temperature sensor

1520-01
1. COMPARISON IN COOLING SYSTEM FOR EACH ENGINE
For the D27DTP (POWER UP) engine, the cooling system is equipped with E-EGR cooler and the
water pump which its capacity is improved according to the additional coolant line in the cylinder
block. For the D27DT engine, the cooling system uses the fan clutch.
Cooling System for D27DTP (POWER UP) Engine

D27DT Engine
D27DTP (POWER UP) & D27DT (EU IV) Engine
Comparison