2012 SSANGYONG NEW ACTYON SPORTS check oil

09-134850-01
Maximum Stroke of Brake Pedal ▶
Check the brake pedal with below
procedures: -
Start the engine.
Pump the brake pedal around 3 times.
Depress the brake pedal with approx. 30
kg and measure the distance (A) between
the upper surface of pedal pad and the
lower dash panel.
If the measured value is out of the
specified value, adjust the length. 1.
2.
3.
4.
Specified value (A)150mm
5. BRAKE SYSTEM CHECK
Over the specified value
Cause Action
Worn brake pad Replace
Worn brake shoe Replace
Improper stroke of hand
brakeAdjust
Air in brake line Air bleeding
Oil leak Repair or replace
Brake booster push rod Replace or adjust
Improperly adjusted
stopper boltAdjust
Below the specified value
Cause Action
Brake booster push rod
Replace or adjust
Air in brake fluid Replace
Improperly adjusted
stopper boltAdjust

09-174850-01
Brake Fluid ▶
Brake Fluid Type ▶ 1. Color
Ligh gold (New oil) → Brown → Black -
2. Service Interval/Type
Change: every 2 years, Type: DOT4
The water in the brake fluid has an adverse effect to the brake system. If the fluid contains
around 3% of water, the boiling point of the brake fluid goes down by 25%. It will cause
the vapor lock frequently.
Water content in fluid: around 3% after 18 months, around 7~10% after few years
The water ib fluid makes the corrosion in the brake lines, deforms and deteriorates the
rubber components, brake calipers and pistons. -
DOT4: Brake fluid for premium vehicle. Lower water absorbing rate AND higher boiling point
than DOT3
Brake Fluid Level Check ▶
The brake fluid level should be between "MAX"
and "MIN" on the reservoir. If it is below "MIN"
mark, check for oil leaks and refill the reservoir
with the specified fluid.

09-194850-01
Clean the dissembled components and visually check the followings:
Damage and tear on boot 4.
Uneven wear and oil contamination 5.
Damage, crack and wear on cylinder body
(A) and guide pin (B) 6.
Wear, rust and damage on the cylinder and
piston
Scratch and bending on disc plate 7.
8.

12-34610-01
1. SPECIFICATIONS
Description Specification
Steering wheel Type 4-spoke type
Gear box Type Rack and pinion type
Gear ratio 40.245
Steering angle Inner37.59˚
Outer33.48˚
Oil pump Type Vane type
Maximum pressure (kgf/cm2)90 ± 3
Pulley size (mm)Ø115
Operating temperature-40℃~150℃
Minimum turning radius (m) 5.95
Steering oil Type ATF Dexron II or III
TOTAL FLUIDE DA
(Extreme cold condition only)
Capacity (L) Approx. 1.0
Service interval Daily check and add if necessary.

12-114610-01
Oil Change ▶
Open the power fluid reservoir cap and
drain the fluid completely with oil suction
device. To make it easy, turn the steering
wheel to its both ends several times.
Fill up the specified fluid into fluid reservoir
and bleed air from the steering system. 1.
2. Oil Level Check ▶
Place the vehicle on a level ground and
start the engine and let it run at idle speed.
Turn the steering wheel several times so
that the oil temperature reaches to normal
operating level (75~85˚C).
Place the steering wheel at straight ahead
direction.
Check the oil level in the power steering oil
reservoir. Adjust the oil level between MAX
and MIN. 1.
2.
3.
4.
If the difference between two
measurements is below 5 mm and the level
is between MAX and MIN level, it's normal.
If it is over 5 mm, bleed air from the
system. Check the fluid level on a level ground with
the engine turned off. The fluid level should
be between the MIN and MAX marks on the
reservoir cap gauge.
below 5 mm
Engine idling Engine running
Oil typeATF Dexron II or III
Capacityapprox. 1ℓ (including
reservoir)

12-12
Air Bleeding ▶
Lift up the vehicle very carefully.
Turn the steering wheel to its both ends
several times and add the oil up to MAX
line in the steering oil reservoir.
Periodically crank the starting motor and
turn the steering wheel to its both ends
without any interruption.
Check the oil level again. If the oil level is
fluctuated, repeat the procedures from
step 3 to step 5.
Start the engine.
Turn the steering wheel to its both ends
until any bubble can be found in the
steering oil reservoir.
Perform the test drive and check the
steering wheel for normal operation and
noise.
If the oil level abruptly goes up, bleed the
air from the system again. 1.
2.
3.
4.
5.
6.
7.
8.
The air bleeding should be done after
servicing the power steering system and when
the difference between two measurements
(cooled and normal temperature) is
prominent.
Max
Min
Normal Abnormal
If the air bleeding is not properly
performed, the life span of the power
steering pump may be shortened. -

12-134610-01
Oil Pump Pressure Check ▶
Unscrew the pressure line fitting in power
steering pump.
Install the pressure gauge between the
power steering pump and the power
steering oil pressure line.
Place the shift lever to neutral position.
Apply the parking brake.
Open the valve in pressure gauge. Start
the engine and let it run at idle speed.
Turn the steering wheel several times so
that the oil temperature reaches to normal
operating level. 1.
2.
3.
4.
5.
Before checking the pressure, check the oil
level and belt tension. Prepare the empty
container to collect the spilled oil during the
service. Check the oil pump pressure to locate any
defect in oil pump.
Fully close the valve in pressure gauge and
measure the oil pressure. 6.
Relief pressure
90 ± 3 bar
Oil pump
Steering gear box
To prevent internal damage, do not close
the gauge valve over 10 seconds.
Keep the oil temperature at proper range. -
-