2012 SSANGYONG NEW ACTYON SPORTS display

04-38210-01
1. SPECIFICATIONS
Item Specification
Rated voltage DC 13.5 V
Operating voltage DC 9 V ~ 16 V
Checking voltage DC 13.5 V
Operating temperature-30℃ ~ +80℃
Storage temperature-40℃ ~ +85℃
Illumination color Dial White
Pointer Red
LCD Red
Gear position display in A/T
(Left hand of LCD display)P, R, N, D, 1, 2, 3, 4, 5 and 6

04-4
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
ESP indicator/warning light
Immobilizer indicator
Glow indicator
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32. It sends and receives information to/from each unit through CAN communication line. The LCD
display and separate ESP ON/OFF indicator are newly added.

04-138210-01
3) Fuel Level Gauge
The fuel level gauge displays the resistance value of the float on the fuel sender in the fuel tank
through a pointer. Note that this vehicle doesn't have a service hole for checking the fuel sender
connector in the fuel tank.
The fuel sender and its connector can be checked and replaced only when the fuel tank is
removed. The power supply and resistance value should be measured at the connector in front of
the fuel sender (refer to wiring diagram).
When the power supply and output resistance are normal, the float operation by fuel level may be
defective; if so, replace the fuel sender.
Low fuel warning lamp comes on when:
The fuel level drops to 9 L or less. The lamp goes off if the fuel level reaches 9.5 L or more.This table shows the tolerance and resistance value changes by fuel level in normal
conditions. Therefore, the differences that can be occurred by the road conditions and fuel
fluctuations are ignored.

04-14
4) Coolant Temperature Gauge
The coolant temperature gauge displays the coolant temperature with a pointer. The angle of
pointer that changes by coolant temperature is as shown below.
Measurement of coolant temperature sensor resistance
Measure the resistance between the terminal and the ground with an ohmmeter and replace if the
resistance is out of specified range.
Temperature (ºC)20 60 80 100 120
Resistance (Ω)2449Ω ± 5% 589.4kΩ ±
5%321Ω ± 5%185.7kΩ ±
5%112.9kΩ ±
5%
Voltage (V)3.615 1.910 1.259 0.819 0.536
When the resistance value by coolant temperature is within the specified range, check
thermostat, water pump, radiator related coolant circuit for normal operation. Also, check the
wiring harnesses and connectors for proper connection.

04-158210-01
Change
OrderMode LCD Display Description
1 TRIP A The maximum distance value that can be displayed is
999.9 km with increments of 0.1 km. The trip meter is
reset to 0.0 km when the value reaches above 999.9
km. When measuring a trip distance, reset the
distance value in the mode you want to use by
pressing the TRIP switch for 1 sec. or more.
2 TRIP B The maximum distance value that can be displayed is
6,213.09 mi with increments of 0.62mi. The trip meter
is reset to 0.0 km when the value reaches above
999.9 km. When measuring a trip distance, reset the
distance value in the mode you want to use by
pressing the TRIP switch for 1 sec. or more.
3 Distance
to emptyThe estimated distance that can be traveled is
calculated based on the current fuel level.
If the DTE is less than 50 km, "---" flashes on the
display.
4 Driving
timeThe driving time from resetting the value (0:00) until
now is displayed. The value displayed is accumulated
while the engine is running even if the vehicle is not
driven. The display range is 00:00 to 99:59. When
measuring the driving time, press the TRIP switch for
1 sec. or more to reset the value.
5 Average
fuel
economyThe average fuel economy from resetting the value (-
-.-) until now is displayed. The value displayed is
accumulated while the engine is running even if the
vehicle is not driven. The display range is 0.0 to 99.9
km/h. When measuring the average fuel economy,
press the TRIP switch for 1 sec. or more to reset the
value. "--.-" is displayed on the screen when
resetting. The value is reset automatically whenever
the vehicle is fuelled.
5) Description for LCD Display
LCD display
Mode Description ▶

04-16
Change
OrderMode LCD Display Description
6 Instant fuel
consumptionThe fuel range is calculated based on the distance
driven and fuel consumed every 2 seconds. If the
vehicle speed is below 10 km/h or the engine rpm
is 200 rpm or less, the instant fuel economy is not
displayed. The display range is 0.0 to 99.9 km/.
7 Brightness
adjustmentThe brightness of the illumination can be adjusted
in 6 steps by pressing the TRIP switch briefly (less
than 1 sec.). The display is changed from ILL1 to
ILL6 every time the switch is pressed. If you select
one level within the range and press and hold the
TRIP switch, the brightness level is memorized. If
there is no TRIP switch input for 5 seconds or
more, the mode is switched to TRIP A mode
automatically. When the battery is reinstalled, the
brightness level is reset to level 4.

04-18
Brightness of LCD display when turning ON/OFF tail lamp ▶
Sequen
ceLevelTail lamp OFF Tail lamp ON
Display brightness Brightness
ratioDisplay brightness Brightness
ratio
1 ILL1 25% 5%
2 ILL2 40%9%
(LCD: 12%)
3 ILL3 55%13%
(LCD: 19%)
4 ILL4 70%17%
(LCD: 26%)
5 ILL5 85%21%
(LCD: 33%)
6 ILL6 100%25%
(LCD: 40%)
Illumination conditions of LCD display when turning ON/OFF tail lamp ▶
The illumination for the LCD display comes on when turning on the tail lamp and is adjustable only
when the ignition is ON. When turning on the tail lamp switch with the ignition OFF, the tail lamp
comes on but the LCD display is not illuminated. Refer to the illustration below.
IGN ON
(Comes on regardless of whether the tail lamp
switch is turned ON or OFF)Tail lamp comes on with IGN OFF
(Tail lamp comes on but the illumination for LC
D
display is not turned on)

04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON
and OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key
is turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.