2012 SSANGYONG NEW ACTYON SPORTS coolant temperature

02-70000-00
1719-09 Acoustic cover
Changed the design1543-01 Steering pump assembly
Introduced reservoir integrated tpe steering
pump
D20DTR (Actyon Sports)
OldNew
OldNew
OldNew
Power steering pump
Old
New
1533-30 Coolant outlet pipe
OldNew
Coolant temperature sensor hole
EGR cooler
outlet
Coolant temperature sensor hole
EGR cooler outletCoolant outlet pipe
1520-21 Coolant outlet port
Changed the location of coolant
temperature sensor and deleted the
coolant outlet port from turbocharger
1793-23 EGR cooler & coolant outlet
hose

01-4
2. MAJOR COMPONENTS
Front view ▶
Vacuum pump
Oil filter assembly
Camshaft position sensor
Power steering pump pulley
Water pump pulley
Alternator pulley
Idler pulley No. 2
A/C compressor pulley
Auto tensioner
Idler pulley No. 1
Isolation damper
Rear view ▶
E-EGR valve
Fuel temperature sensor
Fuel HP pump assembly
Coolant temperature sensor
IMV valve Crankshaft position sensor
Oil pressure switch

01-50000-00
Right view ▶
Front exhaust gas
temperature sensor
Oil dipstick tube &
gauge assembly
E-VGT actuator
E-VGT turbocharger
Coolant screw plug
Oil drain plug
Left view ▶
Thermostat assembly
Variable swirl valve assembly
E-EGR valve
E-EGR solenoid valve
EGR cooler
Electronic throttle body
Oil cooler assembly

01-70000-00
1) Service Interval
2) Specification and Capacity
Engine oilSpecification Quality class: Ssangyong genuine engine oil (Total Quartz INEO
ECS 5W 30, SK ZIC SY 5W 30) or oil Approved by MB Sheet 229.51
Capacity approx. 6.0 litter
Engine
coolantSpecification Ssangyong genuine coolant Anti-Freeze SYC-1025
Capacity approx. 8.5 litter
Severe condition
Frequent stop-and-go traffic, extended idling, short driving distance below 6 km, driving distance
below 16 km when the outside temperature remains below freezing
Driving in a hilly or mountainous terrain, sandy, or dusty area
High load driving such as trailer towing
Taxi, patrol service or delivery service (extended idling and excessive driving with low speed) -
-
-
-
DescriptionDaily
inspectionWeekly
inspectionService interval
Engine oil &
oil filterInspection - EU Change every 20,000 km or 12 months
(The service interval should be
shortened under severe conditions)
General Change every 15,000 km or 12 months
(The service interval should be
shortened under severe conditions)
Coolant Inspection - Change every 200,000 km or 5 years
Air cleaner
element- Inspection Diesel EU Change every 20,000 km
(The service interval should
be shortened under severe
conditions)
General Clean every 7,500 km,
change every 15,000 km
(The service interval should
be shortened under severe
conditions)
Gasoline Clean every 15,000 km, replace every
60,000 km (The service interval should
be shortened under severe conditions)
Fuel filter - - EU Change every 40,000 km (Draining
water from fuel filter: whenever
replacing the engine oil)
General Change every 45,000 km (Draining
water from fuel filter: whenever
replacing the engine oil)

02-4
2. TIGHTENING TORQUE
Component SizeBolt
QuantitySpecified torque
(Nm)Remark
(Total torque)
Main bearing capM12×8210 55±5Nm,
180˚Not re-usable
Connecting rod capM9×52840±5Nm,
90˚+10˚50 to 80 Nm
Rear coverM6×20610 ± 1 Nm-
Oil pumpM8×35SOC325 ± 2.5 Nm-
FlywheelM10×22845 ± 5 Nm,
90˚+10˚60 to 100 Nm
Crankshaft center boltM20×851200 ± 20 Nm,
180˚+20˚660 to 720 Nm
Not re-usable
Oil panM6×201810 ± 1 Nm-
M6×35210 ± 1 Nm-
M6×85210 ± 1 Nm-
M6×120210 ± 1 Nm-
M8×40225 ± 2.5 Nm-
HP pump main nutM14×1.5-8-1165 ± 5 Nm-
HP pump boltM8×55325 ± 2.5 Nm-
Cylinder headM13×15012 85Nm
270°±10°-
Camshaft capM6×301610 ± 1 Nm -
M8×60425 ± 2.5 Nm -
Exhaust stud bolt 1015±1.5Nm-
Exhaust sprocket boltM11×40130 ± 3 Nm -
Chain tensioner screw
boltM38×1.5 125±2.5Nm -
Coolant temperature
sensor120±2.0Nm -
Auto tensionerM8×30(LOW) 125±2.5Nm -
M10×75(Upper) 155±5.5Nm -
Coolant pumpM6×50 110±1.0Nm -

03-16
Dynamic test for backleak of injector ▶
Warm up the engine so that the engine
coolant temperature be over 80℃ and star
the engine again.
Disconnect the injector return hose and
cover the openings with caps shaped
screw (included in the special tool).. 1.
2.
Connect the hose of the container for
measuring backleak to the return nipple of
the injector.
Start the engine again and let the engine
idle for 30 seconds.
Perform backleak test of fuel system with a
diagnostic device after 30 seconds. 3.
4.
5.
This test consists of 4 cycles, and the engine
rpm reaches 3,500 rpm for 18 seconds in each
cycle.
Check the amount of backleak collected
into the container and confirm that it is
within the specified range. 6.
Specification38 ml or less

03-26
The engine ECU calculates the accelerator pedal based on the input signals from various sensors,
and controls the overall operation of the vehicle.
The ECU receives the signals from various sensor through data line, and performs effective air-fuel
ratio control based on these signals.
The crankshaft speed (position) sensor measures the engine speed, and the camshaft speed
(position) sensor determines the order of injections, and the ECU detects the amount of the
accelerator pedal depressed (driver's will) by receiving the electrical signals from the accelerator
pedal sensor.
The mass air flow sensor detects the volume of intake air and sends the value to the ECU.
The major function of the ECU is controlling air-fuel ratio to reduce the emission level (EGR valve
control) by detecting instantaneous air flow change with the signals from the mass air flow sensor.
Also, the ECU uses the signals from the coolant temperature & air temperature sensors, booster
pressure sensor, atmospheric pressure sensor to: a) determine injection starting point and set
value for pilot injection, and b) deal with various operations and variable conditions.

06-191914-01
T-MAP sensor
Booster pressure and
temperature
E-VGT turbocharger
Improves engine power
2. COMPONENTS
Engine ECU (D20DTR)
E-VGT duty controlAccelerator pedal position
sensor
Transfers driver's will to
accelerate to ECU
Atmospheric pressure, RPM
signal
HFM sensor
Improves the engine powerCoolant temperature sensor
Operates the VGT according
to engine warm-up
* 세부제어로직은 엔진제어편 참조