2012 SSANGYONG KORANDO light

03-14
Rain sensor coupled wiper (LIN) ▶
System layout 1.
Data recognition & operation 2.
Data recognition time
The system performs LIN communication regardless of the conditions of wiper and light switch when
the ignition switch is in ON position. If the intermittent/automatic wiper switch is in "AUTO" and the
light switch is in "AUTO" position, the wiper system operates according to the LIN data.
The data received from the rain sensor is recognized for 2 times consecutively.
Operation when recognizing data
No data: wiper low/high relay OFF
Low speed signal: low relay ON (ON for at least one cycle), but high relay OFF
High speed signal: high relay ON (ON for at least one cycle), but low relay OFF
The washer switch signal is overridden during continuous operation of the wiper.
(Washer coupled wiper function is available only during intermittent operation) -
-

03-358710-01
10) Keyless Entry
Transmitter (REKES key) ▶
When the user operates the switch of the remote control key, the vehicle control messages formatted by
its CPU are sent to the main unit wirelessly. The, the CPU control the vehicle and the main unit controls
the vehicle operation.
Door unlock/panic buttonDoor lock
Door unlock/panic button ▶
Unlocking door and tailgate (briefly press)
If you press this button, it unlocks all doors and the tailgate and deactivates the theft deterrent mode.
When the theft deterrent mode is deactivated, the emergency hazard lights blink once.
If the door, tailgate or engine hood is not opened within 30 seconds after unlocking the door with the
remote control key in theft deterrent mode, the door is locked automatically, hazard warning flasher
blinks twice and buzzer sounds once. (entering into theft deterrent mode)
Panic function (press and hold for more than 2 sec)
When pressing (over 2 sec) the button, the hazard warning flasher blinks and buzzer sounds for
about 30 seconds.
Press the UNLOCK or PANIC button to deactivate this function. 1.
-
-
-
2.
-
-

03-478710-01
Coming home lighting control ▶
The low beam keeps on for 30 seconds when the ignition switch is turned to ON from OFF position
with the headlamp ON.
Coming home lighting OFF condition
This function can be activated or deactivated with the diagnostic device. (default setting: active) 1.
2.
3.3 minutes after all doors and tailgate are open and closed
(lighting goes off 30 seconds after without extension when the closed doors are open)
When receiving REKES and passenger door lock signals (close, open, close) twice during coming
home lighting operation
Lighting goes off during its operation when headlamp and AUTO light switch are turned to other
position than ON
Lighting goes off when ignition switch is turned to ON position -
-
-
-
13) Headlamp

03-56
16) Time Lag Power Window Control
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is
immediately turned OFF. 1.
2.
3.
17) Sleep Mode
If the driver door/passenger door/rear doors/tailgate lock switch is not changed for 6 seconds with all
driver door/passenger door/rear doors/tailgate closed, key removed, IGN1 and IGN2 OFF, the
vehicle enters into sleep mode for system power down.
If any of conditions in Step (1) is not satisfied, the System Wake-up mode is activated.
When output such as room lamp, key hole illumination, tail lamps and power window is activating or
all the doors keep closed for 30 seconds after door is unlocked for conditions in Step (1), the system
is in normal mode. Then, if there is no change within 6 seconds with all output conditions and ready
conditions released and all the doors closed, the sleep mode is activated.
When turning on the overhead room lamp switch, the overhead room lamps come on for 10 minutes
and go off, and the sleep mode is activated after 6 seconds.
When the coming home light OFF conditions are satisfied, the sleep mode is activated.
In this condition, when opening a door or inserting the ignition key into key hole, the sleep mode is
deactivated. 1.
2.
3.
4.
5.
6.

03-638710-01
19) DRL (Daytime Running Light) Control
When receiving the DRL activation signal, the tail lamps are turned ON when turning the ignition
switch to ON position, and the headlamps are turned ON when the engine speed is 300 rpm or
higher.
When turning ON the tail lamp switch during engine running, the headlamps are turned OFF.
The headlamps do not come ON when the engine speed is above 300 rpm with the tail lamp switch
ON.
The auto light sensor is not available in the vehicle with DRL system.
If there is no DRL activation signal, the light system operates in normal conditions. 1.
2.
3.
4.
5.
20) Fog Lamp Control
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps
are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps
are turned OFF.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamps should not automatically come on again if they have been turned OFF by any
other way other than the switch. 1.
2.
3.
(The rear fog lamps are applied to only EU region)

03-64
21) Auto Light Control (LIN)
The BCM communicates with the auto light sensor when turning the ignition switch to ON position, and
controls the tail lamps and the headlamps depending on the LIN data with the light switch AUTO. 1.

03-698710-01
3) Operation of Immobilizer
When the ignition switch is turned to the ON position with REKES key, the BCM checks the crypto code
of the inserted key using the immobilizer antenna and sends whether the engine is startable or not to the
engine ECU through the CAN communication so that the engine can be started.
BCM
REKES key
Immobilizer antenna
ECUCAN line
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system error:
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves other
than Ssangyong products.
When the key is close to any electronic or electric devices such as lighting equipment, security keys
or security cards.
When the key is close to a magnetic or metal object or a battery. -
-
-
-