2012 RENAULT SCENIC relay

13B-256
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF997
CONTINUED
Check the absence of interference resistance on the following connections:
•3JA between components 120 and 1067 or 1550,
•3JAA between components 120 and 1068 or 1550,
•3JAB between components 120 and 1069 or 1550.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the + 12 V after relay supply to the thermoplunger 1, thermoplunger 2, thermoplunger 3 relay mounting of
the following connections:
•3FB of component 1067 or 1550,
•BP91 of component 1068 or 1550,
•BP9 of component 1069 or 1550.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Actuate the various thermoplunger relays one by one using commands:
– AC063 Thermoplunger no. 1 relay
– AC064 Thermoplunger no. 2 relay
– AC031 Thermoplunger no. 3 relay
Check the voltage using a multimeter. If the voltage is zero, the thermoplunger is faulty.
Only replace the faulty thermoplunger.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-262V12 MR-372-J84-13B300$090.mif
13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET007Pre-postheating control
ET024Thermoplunger no. 1 request
ET025Thermoplunger no. 2 request
ET026Thermoplunger no. 3 request
ET034Clutch signal registered
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET104Injector code use
ET120Pre-postheating signal
ET143Low-speed fan assembly relay control
ET144High-speed fan assembly relay control
ET205Thermoplunger no. 1 relay control (only on Laguna II ph2 without particle filter)
ET206Thermoplunger no. 2 relay control (only on Laguna II ph2 without particle filter)
ET207Thermoplunger no. 3 relay control (only on Laguna II ph2 without particle filter)
ET238Synchronisation
ET285Injection -> automatic gearbox connection
ET341Immobiliser code programmed
ET405Clutch pedal switch (only for manual gearboxes)
ET415Cruise control/Speed limiter deactivation
ET587Cooling of recirculated exhaust gas
ET589Electric coolant pump control (turbocharger)
ET615Automatic gearbox lever position
ET651EGR programming cut-off
DIESEL INJECTION
Fault finding – Status summary table

13B-264V12 MR-372-J84-13B300$101.mif
13B
ET001COMPUTER + AFTER IGNITION FEED
STATUS
DEFINITIONPRESENT: This status indicates that the + after ignition feed is active.
ABSENT: This status indicates that the + after ignition feed is not active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"PRESENT"Ignition on and engine running warm at idle speed with the + after ignition feed
activated.
Normal operating condition.
The computer is correctly supplied after the ignition has been switched on.
In the event of a fault, refer to the interpretation of DF046 Battery voltage or DF151
Main relay circuit.
Sensor electrical conformity.
"ABSENT"
NOTESIgnition on
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16CP33_V18_ET001 / EDC16CP33_V1C_ET001 / EDC16CP33_V54_ET001 / EDC16CP33_V20_ET001 / EDC16CP33_V58_ET001 /
EDC16CP33_V5C_ET001 / EDC16CP33_V24_ET001 / EDC16CP33_V04_ET001 / EDC16CP33_V08_ET001 / EDC16CP33_V44_ET001 /
EDC16CP33_V4C_ET001 / EDC16CP33_V34_ET001 / EDC16CP33_V38_ET001 / EDC16CP33_V74_ET001 / EDC16CP33_V28_ET001 /
EDC16CP33_V62_ET001 / EDC16CP33_V26_ET001 / EDC16CP33_V60_ET001
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-265V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET001
CONTINUED
If the ignition is not switched on, status ET001 should be ABSENT.
As soon as the ignition is switched on, the computer should be supplied with power. Status ET001 becomes
PRESENT.
If this status remains locked on ABSENT, follow the procedure below:
– Check the condition of fuse FM3 (30A) in the engine fuse and relay box (see MR 395 (Laguna II ph2), 405
(Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of components).
– Check the condition of fuse F18 (15A) in the Protection and Switching Unit (UPC) (see MR364 (Mégane II ph2),
MR370 (Scénic II ph2) Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the continuity and absence of interference resistance on the following connection:
•3AA between components 120 and 983 or 1337.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-267V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007PRE-POSTHEATING UNIT CONTROL
STATUS
DEFINITIONACTIVE: when the heater plugs are activated according to the engine coolant
temperature.
INACTIVE: after the engine has been running for a certain period
In the event of a fault, consult the interpretation of fault DF017 Preheating unit
control circuit.
NOTESSpecial notes:
This status is specific to slow heater plugs (black ring).
Conformity check with engine stopped and ignition on.
"ACTIVE"When the ignition is switched on, status ET007 should be ACTIVE for a time that varies
according to the engine coolant temperature. Both the relay and the heater plugs are
supplied.
After starting, the status should remain ACTIVE for a time that varies according
to the engine temperature. This is the postheating phase.
If ET007 is INACTIVE when the ignition is switched on, check:
– Supply fuse FM12 (70A) of component 597 (engine fuse and relay box) or F2 (70A)
of component 777 for Mégane II and Scénic II
–The supply to the heater plugs after relay actuation, and the connections of the
heater plugs.
Important: on this engine, the plug supply voltage is variable.
– Check the continuity and absence of interference resistance of the following
connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
EDC16CP33_V18_ET007 / EDC16CP33_V1C_ET007 / EDC16CP33_V54_ET007 / EDC16CP33_V20_ET007 / EDC16CP33_V58_ET007 /
EDC16CP33_V5C_ET007 / EDC16CP33_V24_ET007 / EDC16CP33_V04_ET007 / EDC16CP33_V08_ET007 / EDC16CP33_V44_ET007 /
EDC16CP33_V4C_ET007 / EDC16CP33_V34_ET007 / EDC16CP33_V38_ET007 / EDC16CP33_V74_ET007 / EDC16CP33_V28_ET007 /
EDC16CP33_V26_ET007
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-269V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET024
ET025
ET026THERMOPLUNGER NO. 1 REQUESTTHERMOPLUNGER NO. 2 REQUEST
THERMOPLUNGER NO. 3 REQUEST
STATUS
DEFINITIONACTIVE: These statuses indicate that the thermoplungers are active.
INACTIVE: These statuses indicate that the thermoplungers are inactive.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"INACTIVE"Statuses ET024, ET025, and ET026 are INACTIVE when the ignition is switched on
with the engine stopped, or when the engine is warm.
"ACTIVE"Statuses ET024, ET025, and ET026 are ACTIVE when:
– the engine has been started,
– and the engine coolant temperature is low (< 15°C),
– and the air temperature is low (< 5°C).
This strategy allows the engine coolant to be heated and to allow the heating of the
passenger compartment.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Thermoplunger no. 1 relay,
– AC064 Thermoplunger no. 2 relay,
– AC031 Thermoplunger no. 3 relay.
In the event of a fault, refer to the interpretation of faults:
– DF032 Thermoplunger no. 1 relay control circuit,
– DF033 Thermoplunger no. 2 relay control circuit,
– DF034 Thermoplunger no. 3 relay control circuit.
EDC16CP33_V18_ET024 / EDC16CP33_V18_ET025 / EDC16CP33_V18_ET026 / EDC16CP33_V1C_ET024 / EDC16CP33_V1C_ET025 /
EDC16CP33_V1C_ET026 / EDC16CP33_V54_ET024 / EDC16CP33_V54_ET025 / EDC16CP33_V54_ET026 / EDC16CP33_V20_ET024 /
EDC16CP33_V20_ET025 / EDC16CP33_V20_ET026 / EDC16CP33_V58_ET024 / EDC16CP33_V58_ET025 / EDC16CP33_V58_ET026 /
EDC16CP33_V5C_ET024 / EDC16CP33_V5C_ET025 / EDC16CP33_V5C_ET026 / EDC16CP33_V24_ET024 / EDC16CP33_V24_ET025 /
EDC16CP33_V24_ET026 / EDC16CP33_V28_ET024 / EDC16CP33_V28_ET025 / EDC16CP33_V28_ET026 / EDC16CP33_V62_ET024 /
EDC16CP33_V62_ET025 / EDC16CP33_V62_ET026 / EDC16CP33_V26_ET024 / EDC16CP33_V60_ET024 / EDC16CP33_V26_ET025 /
EDC16CP33_V60_ET025 / EDC16CP33_V26_ET026 / EDC16CP33_V60_ET026
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-286V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143LOW-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS
DEFINITIONThis status indicates whether the low speed fan assembly is active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
If the vehicle is fitted with air conditioning, the fan assembly electrical circuit includes
2 relays. The 1
st speed fan assembly relay will be actuated when the engine coolant
temperature exceeds 99°C and its function is to cool the engine so that the engine
temperature does not exceed 102°C. If the engine coolant temperature exceeds 102°C,
the 2
nd speed fan assembly relay will be actuated and the fan will rotate faster.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
IMPORTANT:
If the vehicle is equipped with air conditioning, the engine cooling fan will operate at 1
st speed as soon as the air
conditioning compressor is activated.
Conformity check with engine stopped and ignition on.
"INACTIVE"Engine cold and air conditioning switched off
In the event of a fault, consult the interpretation of fault DF018 Low speed fan
assembly control circuit.
EDC16CP33_V18_ET143 / EDC16CP33_V1C_ET143 / EDC16CP33_V54_ET143 / EDC16CP33_V20_ET143 / EDC16CP33_V58_ET143 /
EDC16CP33_V5C_ET143 / EDC16CP33_V24_ET143 / EDC16CP33_V04_ET143 / EDC16CP33_V08_ET143 / EDC16CP33_V44_ET143 /
EDC16CP33_V4C_ET143 / EDC16CP33_V34_ET143 / EDC16CP33_V38_ET143 / EDC16CP33_V74_ET143 / EDC16CP33_V28_ET143 /
EDC16CP33_V26_ET143
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-287V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143
CONTINUED 1
Conformity check with the engine running and engine coolant temperature > 80°C
INACTIVE or ACTIVE, depending on the engine temperature (air conditioning switched off).
In the event of a fault, refer to the interpretation of fault DF018.
Sensor electrical conformity
"ACTIVE"When the coolant reaches 99°C, the injection computer actuates the low-speed fan
assembly relay, and status ET143 becomes ACTIVE. The relay then supplies the
fan assembly and the cooling fan begins to turn.
If status ET143 is ACTIVE, but the cooling fan is not running, perform the following
operations:
Check the condition of fuse FM15 (60 A) in the engine fuse and relay box (see MR364
(Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis
ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of
components).
Disconnect the low speed and high speed relays, check that they are operating
correctly and check the condition of the relay mounting connectors (see Wiring
Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II
ph2, Scénic II ph2, component code 597).
If one of the connectors is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, wiring: precautions for repair), repair the
connector, otherwise replace the wiring.
Check the + 12 V after relay supply to the low speed fan assembly relay on the
following connection:
•3FB of component 700.
Check the continuity and absence of interference resistance of the following
connections:
•49L between components 700 and 321,
•49B between components 262 and 321,
•3JN between components 700 and 120.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74