2012 RENAULT SCENIC ignition

13B-295V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341IMMOBILISER CODE PROGRAMMED
STATUS
DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"YES"Status ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised
.
The engine is only authorised to start if the code is correctly recognised by the UCH
computer and statusET003 Engine immobiliser is INACTIVE.
In the event of a fault, (see 87B, Passenger compartment connection unit,
Conformity check).
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault-finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection
computer is possible.
If dialogue is not established, contact Techline.
EDC16CP33_V18_ET341 / EDC16CP33_V1C_ET341 / EDC16CP33_V54_ET341 / EDC16CP33_V20_ET341 / EDC16CP33_V58_ET341 /
EDC16CP33_V5C_ET341 / EDC16CP33_V24_ET341 / EDC16CP33_V04_ET341 / EDC16CP33_V08_ET341 / EDC16CP33_V44_ET341 /
EDC16CP33_V4C_ET341 / EDC16CP33_V34_ET341 / EDC16CP33_V38_ET341 / EDC16CP33_V74_ET341 / EDC16CP33_V28_ET341 /
EDC16CP33_V62_ET341 / EDC16CP33_V26_ET341 / EDC16CP33_V60_ET341
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-296V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESCan only be displayed for manual gearboxes.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
Sensor electrical conformity
EDC16CP33_V18_ET405 / EDC16CP33_V1C_ET405 / EDC16CP33_V54_ET405 / EDC16CP33_V20_ET405 / EDC16CP33_V58_ET405 /
EDC16CP33_V5C_ET405 / EDC16CP33_V24_ET405 / EDC16CP33_V04_ET405 / EDC16CP33_V08_ET405 / EDC16CP33_V44_ET405 /
EDC16CP33_V4C_ET405 / EDC16CP33_V34_ET405 / EDC16CP33_V38_ET405 / EDC16CP33_V74_ET405 / EDC16CP33_V28_ET405 /
EDC16CP33_V62_ET405 / EDC16CP33_V26_ET405 / EDC16CP33_V60_ET405
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-298V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESNone.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control / speed limiter function, due to
a driver request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 "Fault memory" to reset this status to "NONE".
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Gear lever in neutral (manual gearbox) or neutral position (automatic gearbox).
EDC16CP33_V18_ET415 / EDC16CP33_V1C_ET415 / EDC16CP33_V54_ET415 / EDC16CP33_V20_ET415 / EDC16CP33_V58_ET415 /
EDC16CP33_V5C_ET415 / EDC16CP33_V24_ET415 / EDC16CP33_V04_ET415 / EDC16CP33_V08_ET415 / EDC16CP33_V44_ET415 /
EDC16CP33_V4C_ET415 / EDC16CP33_V34_ET415 / EDC16CP33_V38_ET415 / EDC16CP33_V74_ET415 / EDC16CP33_V28_ET415 /
EDC16CP33_V62_ET415 / EDC16CP33_V26_ET415 / EDC16CP33_V60_ET415
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-305V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET587RECIRCULATED EXHAUST GAS COOLING
STATUS
DEFINITIONACTIVE: This status indicates that exhaust gas cooling is recirculated.
INACTIVE: This status indicates that exhaust gas cooling is not recirculated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE:
According to computer programming.
In the event of a fault, consult the interpretation of faults
DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation
.
EDC16CP33_V18_ET587 / EDC16CP33_V1C_ET587 / EDC16CP33_V54_ET587 / EDC16CP33_V20_ET587 / EDC16CP33_V58_ET587 /
EDC16CP33_V5C_ET587 / EDC16CP33_V24_ET587 / EDC16CP33_V04_ET587 / EDC16CP33_V08_ET587 / EDC16CP33_V44_ET587 /
EDC16CP33_V4C_ET587 / EDC16CP33_V34_ET587 / EDC16CP33_V38_ET587 / EDC16CP33_V74_ET587 / EDC16CP33_V28_ET587 /
EDC16CP33_V62_ET587 / EDC16CP33_V26_ET587 / EDC16CP33_V60_ET587
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-306V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET615AUTOMATIC GEARBOX LEVER POSITION
STATUS
DEFINITIONNeutral, 1, 2, 3, 4, 5, 6, reverse.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
This status is specific to engine types M9R 721 and M9R 761.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NEUTRALThis status indicates that the gear lever is in neutral.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
1This status indicates that the gearbox is in 1st gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
2This status indicates that the gearbox is in 2nd gear.
If this status is incorrect,
perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
EDC16CP33_V18_ET615 / EDC16CP33_V1C_ET615 / EDC16CP33_V54_ET615 / EDC16CP33_V20_ET615 / EDC16CP33_V58_ET615 /
EDC16CP33_V5C_ET615 / EDC16CP33_V24_ET615 / EDC16CP33_V28_ET615 / EDC16CP33_V62_ET615 / EDC16CP33_V26_ET615 /
EDC16CP33_V60_ET615
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-308V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651EGR PROGRAMMING CUT-OFF
STATUS
DEFINITIONThis status indicates the operating mode of the EGR valve and has 25 different
definitions: STATUS 1 to 24 or NONE.
NOTESNone.
NONENo EGR cut-off, the EGR valve is operating correctly in accordance with
the computer programs.
STATUSES
1, 5, 6, 7, 9, 10, 12,
13, 15, 19, 23, 24Switch off the engine and wait for the diagnostic tool message (maximum time
8 minutes) Communication lost with the computer: EDC16CP33, check the
tool connection and computer supply.
Switch the ignition on and check for faults.
Check the battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much or attain an engine speed that is too high.
STATUSES
3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal status (ET405 Clutch pedal switch) is not ACTIVE,
and that the vehicle has stopped completely.
EDC16CP33_V18_ET651 / EDC16CP33_V1C_ET651 / EDC16CP33_V54_ET651 / EDC16CP33_V20_ET651 / EDC16CP33_V58_ET651 /
EDC16CP33_V5C_ET651 / EDC16CP33_V24_ET651 / EDC16CP33_V04_ET651 / EDC16CP33_V08_ET651 / EDC16CP33_V44_ET651 /
EDC16CP33_V4C_ET651 / EDC16CP33_V34_ET651 / EDC16CP33_V38_ET651 / EDC16CP33_V74_ET651 / EDC16CP33_V28_ET651 /
EDC16CP33_V62_ET651 / EDC16CP33_V26_ET651 / EDC16CP33_V60_ET651
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-310V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS
DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
PLUS: Increase button pressed.
MINUS: Decrease button pressed
.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"INACTIVE"When no button has been pressed.
In the event of a fault, refer to the interpretation of status ET703.
"SUSPEND"'0' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"REACTIVATE"'R' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"MINUS"Decrease button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"PLUS"Increase button pressed.
In the event of a fault, refer to the interpretation of status ET703.
EDC16CP33_V18_ET703 / EDC16CP33_V1C_ET703 / EDC16CP33_V54_ET703 / EDC16CP33_V20_ET703 / EDC16CP33_V58_ET703 /
EDC16CP33_V5C_ET703 / EDC16CP33_V24_ET703 / EDC16CP33_V04_ET703 / EDC16CP33_V08_ET703 / EDC16CP33_V44_ET703 /
EDC16CP33_V4C_ET703 / EDC16CP33_V34_ET703 / EDC16CP33_V38_ET703 / EDC16CP33_V74_ET703 / EDC16CP33_V28_ET703 /
EDC16CP33_V62_ET703 / EDC16CP33_V26_ET703 / EDC16CP33_V60_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-315V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS
DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
NOTESNote:
Statuses ET704 and ET705 must change specification at the same time. If they are
inconsistent, refer to the interpretation of fault DF228 Brake signal.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"ACTIVE"Brake pedal depressed.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, consult the interpretation of ET704 and ET705.
"INACTIVE"Brake pedal released.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, consult the interpretation of ET704 and ET705.
EDC16CP33_V18_ET704 / EDC16CP33_V18_ET705 / EDC16CP33_V1C_ET704 / EDC16CP33_V1C_ET705 / EDC16CP33_V54_ET704 /
EDC16CP33_V54_ET705 / EDC16CP33_V20_ET704 / EDC16CP33_V20_ET705 / EDC16CP33_V58_ET704 / EDC16CP33_V58_ET705 /
EDC16CP33_V5C_ET704 / EDC16CP33_V5C_ET705 / EDC16CP33_V24_ET704 / EDC16CP33_V24_ET705 / EDC16CP33_V04_ET704 /
EDC16CP33_V04_ET705 / EDC16CP33_V08_ET704 / EDC16CP33_V08_ET705 / EDC16CP33_V44_ET704 / EDC16CP33_V44_ET705 /
EDC16CP33_V4C_ET704 / EDC16CP33_V4C_ET705 / EDC16CP33_V34_ET704 / EDC16CP33_V34_ET705 / EDC16CP33_V38_ET704 /
EDC16CP33_V38_ET705 / EDC16CP33_V74_ET704 / EDC16CP33_V74_ET705 / EDC16CP33_V28_ET704 / EDC16CP33_V28_ET705 /
EDC16CP33_V62_ET704 / EDC16CP33_V62_ET705 / EDC16CP33_V26_ET704 / EDC16CP33_V60_ET704 / EDC16CP33_V26_ET705 /
EDC16CP33_V60_ET705
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.