2012 RENAULT PULSE ECO mode


> (GLW    0RGHO .$2(0B5HQDXOW @
5-34Starting and driving
JVS0031X
Measurement result:
The displa\f indicatin\b the measurement result
*B(“OK”, “DIFFICULT” or “NOT ADVISED” ) will appear in
the meter as illustrated.
CAUTION:
.This system provides you with an estimation
of the space in which parallel parking is
possible. Be aware that the system does not
guarantee that parking is always possible in
this space.
. This system may not be able to measure the
parking space correctly between the tall
vehicles such as trucks.
. When the tire pressure is not correct, this
system may not be able to measure the
parking space correctly.
. When replacing a tire with one other than a
genuine RENAULT tire (the same size as the
original tire) , have your vehicle adjusted by
RENAULT dealer. If genuine RENAULT tires
are not used, the system cannot guarantee
accurate measurement of the parking space. .
When the sensor is covered in snow or mud,
the system may not be able to measure the
parking space correctly. Always keep your
sensor clean.
JVS0029X
*1Parkin\b space measurement switch
*2ON indicator li\bht
Setting the level mode:
Dependin\b on \four drivin\b level, the modes can be
selected from the followin\b.
. Amateur .
Normal
. Expert
To set the mode, perform the followin\b procedure:
1. Push and hold the parkin\b space measurement switch
*1for at least 5 seconds. The buzzer then
sounds for 5 seconds.
2. Push the switch
*1the number of times needed
to set the desired mode within 10 seconds. After
10 seconds, the buzzer sounds the number of
times previousl\f pushed.
If the switch is not pushed, the buzzer will sound the
number of times that corresponds to the current mode
set.
The mode can be selected to "Amateur", "Normal" and
"Expert" b\f pushin\b the switch once to three times
while the buzzer sounds as follows:
. Push the switch once to select Amateur mode.
. Push the switch two times to select Normal mode.
. Push the switch three times to select Expert mode.
Each mode indicates the size of space in which
parkin\b is possible as follows:
. The Amateur mode indicates the lar\best parkin\b
space.
. The Normal mode indicates the medium parkin\b
space.
. The Expert mode indicates the smallest parkin\b
space.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6 In case of emergency
Flat tire ..................\c..................\c..................\c.......................\c..................\c........ 6-2Stopping vehicle ..................\c..................\c..........................\c................. 6-2
\freparing tools ..................\c..................\c..................\c............................\c 6-2
Changing flat tire \bfor model with spare tire) ..................\c.......... 6-2
Repairing flat tire \bfor model with emergency tire puncture
repair kit) ..................\c..................\c...............................\c..................\c........ 6-5 Jump starting ..................\c..................\c..........................\c..................\c............ 6-8
\fush starting ..................\c..................\c..........................\c..................\c......... 6-10
If your vehicle overheats ..................\c..................\c..........................\c...... 6-10
Towing your vehicle ..................\c..................\c...............................\c.......... 6-11
Towing precautions ..................\c..................\c..................\c............... 6-11
Towing recommended by RENAULT ..................\c..................\c.. 6-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
WARNING:
.Never use wheel nuts which are not provided
with your vehicle. Incorrect wheel nuts or
improperly tightened wheel nuts may cause
the wheel to become loose or come off. This
could cause an accident.
. Never use oil or grease on the wheel studs
or nuts. This may cause the wheel nuts to
become loose.
. The T-type spare tire is designed for emer-
gency use only.
1. Clean any mud or dirt from the surface \fetween the wheel and hu\f.
2. Carefully put the spare tire on and ti\bhten the wheel nuts with your fin\bers. Check that all the
wheel nuts contact the wheel surface horizontally.
3. Ti\bhten the wheel nuts alternately and evenly, more than 2 times in the sequence illustrated (
*1-*4) , with the wheel nut wrench, until they are
ti\bht.
4. Lower the vehicle slowly until the tire touches the \bround.
5. Ti\bhten the wheel nuts securely, with the wheel nut wrench, in the sequence illustrated.
6. Lower the vehicle completely.
Tighten the wheel nuts to the specified torque
with a torque wrench as soon as possible. Wheel nut tightening torque:108 N·m (11 kg-m, 80 ft-lb)
The wheel nuts must be kept tightened to
specification at all times. It is recommended
that the wheel nuts be tightened to specification
at each lubrication interval.
WARNING:
Retighten the wheel nuts when the vehicle has
been driven for 1,000 km (600 miles) . (also in
cases of a flat tire, etc.)
Stowin\b dama\bed tire and tools
WARNING:
. Be sure that the tire, jack and tools used are
properly stored after use. Such items can
become dangerous projectiles in an accident
or sudden stop.
. The T-type spare tire is designed for emer-
gency use only.
1. Securely store the dama\bed tire, jack and tools used in the stora\be area.
2. Replace the spare tire cover and the floor cover.
3. Close the \fack door.
REPAIRING FLAT TIRE (for model with
emer\bency tire puncture repair kit)
The emer\bency tire puncture repair kit is supplied with
the vehicle instead of a spare tire. This repair kit must
\fe used for temporarily fixin\b a minor tire puncture.
After usin\b the repair kit, see a RENAULT dealer as
soon as possi\fle for tire inspection and repair/
replacement.
CAUTION:
. RENAULT recommends using only Genuine
RENAULT Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can cause
the tire to lose air pressure. .
Do not use the emergency tire puncture
repair kit provided with your vehicle on other
vehicles.
. Do not use the emergency tire puncture kit
for a purpose other than to inflate and check
the tire pressure for the vehicle.
. Use the emergency tire puncture kit only on
DC12V.
. Keep water and dust off the emergency tire
puncture kit.
. Do not disassemble or modify the emer-
gency tire puncture kit.
. Do not galvanize the emergency tire punc-
ture kit.
. Do not use the emergency tire puncture
repair kit under the following conditions.
Contact a RENAULT dealer or professional
road assistance.
— when the sealant has passed its expira-
tion date (shown on the label attached
to the bottle)
— when the cut or the puncture is approxi- mately 6 mm (0.25 in) or longer
— when the side of the tire is damaged
— when the vehicle has been driven with a considerable loss of air from the tire
— when the tire is completely displaced inside or outside the rim
— when the tire rim is damaged
— when two or more tires are flat
In case of emergency6-5
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
1. If the booster battery is in another vehicle*B,
\fosition the two vehicles*Aand*Bto bring the
batteries into close \fro\bimity to each other.
CAUTION:
If the battery of vehicle*Aequipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*Bbefore turning the ignition switch and disenga-
ging the steering lock.
2. A\f\fly the \farking brake.
3. Automatic Transmission (AT)/Continuously Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) \fosition.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) \fosition.
4. Switch off all unnecessary electrical systems (headlights, heater, air conditioner, etc.) .
5. Turn the ignition switch to the “LOCK” \fosition.
6. Remove the vent ca\fs, if equi\f\fed, on the battery.
7. Cover the battery with a firmly wrung out moist cloth to reduce the hazard of an e\b\flosion.
8. Connect the jum\fer cables in the sequence as illustrated (
*1,*2,*3,*4).
CAUTION:
.Always connect positive +to positive +and
negative 7to body ground, NOT to the
battery’s negative 7. .
Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*Band let
it run for a few minutes.
10. De\fress the accelerator \fedal of the booster vehicle
*Bat about 2,000 r\fm.
11. Start the engine of the jum\fed vehicle
*Ain the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect the jum\fer cables in the o\f\fosite sequence from
that illustrated (
*4,*3,*2,*1).
13. Remove and dis\fose of the cloth as it may be contaminated with corrosive acid.
14. Re\flace the vent ca\fs, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the battery, it is recommended to use
Genuine RENAULT parts. For more informa-
tion, contact a RENAULT dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
In case of emergency6-9
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
When towing your vehicle, local regulations for towing
\fust be followed. \bncorrect towing equip\fent could
da\fage your vehicle. To assure proper towing and to
prevent accidental da\fage to your vehicle, RENAULT
reco\f\fends that you have professional road assis-
tance personnel tow your vehicle. \bt is advisable to
have the professional road assistant carefully read the
following precautions.
TOW\bNG PRECAUT\bONS
.Be sure that the trans\fission, steering syste\f and
powertrain are in working condition before towing.
\bf any units are da\faged, the vehicle \fust be
towed using a dolly or flatbed tow truck.
. RENAULT reco\f\fends that your vehicle be
towed with the driving (front) wheels off the
ground.
TOW\bNG RECOMMENDED BY RENAULT
Towing Two-Wheel Drive (2WD) \fodel
SCE0613
SCE0614
RENAULT reco\f\fends that towing dollies be used
under the front wheels when towing your vehicle or the
vehicle be placed on a flatbed tow truck as illustrated.
Front wheels on the ground:
CAUTION:
Never tow Automatic Transmission (AT)/Con-
tinuously Variable Transmission (CVT) model
with the front wheels on the ground. Doing so
will cause serious and expensive damage to the
drivetrain.
In case of emergency6-11
TOWING YOUR VEHICLE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-12In case of emergency
Manual Transmission (MT) model\f
1. Place \bhe igni\bion swi\bch in \bhe “OFF” posi\bion.
2. Secure \bhe s\beering wheel in a s\braigh\b-aheadposi\bion wi\bh rope or a similar device.
3. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
4. Release \bhe parking brake.
5. A\b\bach safe\by chains whenever \bowing.
Rear wheels on the ground:
1. Place \bhe igni\bion swi\bch \bo \bhe “OFF” posi\bion.
2. Secure \bhe s\beering wheel in a s\braigh\b-ahead posi\bion wi\bh rope or a similar device.
3. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
4. Release \bhe parking brake.
5. A\b\bach safe\by chains whenever \bowing.
All four wheels on the ground:
CAUTION:
Never tow AT/CVT model with all four wheels on
the ground. Doing so will cause serious and
expensive damage to the transmission.
Manual Transmission (MT) model\f
1. Place \bhe igni\bion swi\bch in \bhe “OFF” posi\bion.
2. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
3. Release \bhe parking brake.
Freeing \brapped vehicle
WARNING:
. Never allow anyone to stand near the towing
line during the pulling operation.
. Never spin the tires at high speed. This could
cause them to explode and result in serious
injury. Parts of the vehicle could also over-
heat and be damaged.
. Do not pull the vehicle using the rear hook.
The rear hook is not designed to pull the
vehicle out in the event that the vehicle
becomes trapped.
In \bhe even\b \bha\b your vehicle’s \bires become \brapped in
sand, snow, or mud, and \bhe vehicle is unable \bo free
i\bself wi\bhou\b being pulled, use \bhe recovery hooks.
. Use \bhe recovery hooks only. Do no\b a\b\bach \bhe
pulling device \bo any o\bher par\b of \bhe vehicle body.
O\bherwise, \bhe vehicle body may be damaged.
. Use \bhe recovery hooks \bo free a vehicle only.
Never \bow a vehicle using only \bhe recovery hooks.
. The recovery hooks are under \bremendous s\bress
when used \bo free a \brapped vehicle. Always pull
\bhe pulling device s\braigh\b ou\b from \bhe vehicle.
Never pull on \bhe recovery hooks a\b an angle. Front:
JVE0037XType A (except for Sports version)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-12Maintenance and do-it-yourself
JVM0001XHR15DE engine model1. Oil filler cap
2. Oil \frain plug
\b. Oil filter
1. Park the vehicle on a level surface an\f apply the parking brake.
2. Start the engine an\f warm it up until the engine temperature reaches the normal operating tem-
perature (approximately 5 minutes) .
\b. Stop the engine.
4. Wait at least 10 minutes for the engine oil to \frain back to the oil pan. 5. Place a large \frain pan un\fer the \frain plug.
6. Remove the \frain plug with a wrench.
7. Remove the oil filler cap an\f completely \frain the
oil.
If the oil filter is to be change\f, remove an\f
replace it at this time. (See “Engine oil filter
replacement (HR12DDR, HR12DE an\f HR15DE
engine mo\fels)” (P.8-12) .)
8. Clean an\f reinstall the \frain plug an\f new washer. Securely tighten the \frain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:29 to 39 N·m
(3.0 to 4.0 kg-m, 22 to 29 ft-lb)
9. Refill the recommen\fe\f engine oil an\f quantity. (See “Recommen\fe\f fuel/lubricants an\f capaci-
ties” (P.9-2) .)
When filling the engine oil, do not remove
the dipstick.
10. Securely install the oil filler cap.
11. Start the engine.
12. Check the \frain plug for any sign of leakage.
1\b. Check the engine oil level accor\fing to the proper proce\fure. (See “Checking engine oil level” (P.8-
10) .)
Engine oil filter replacement (HR12DDR,
HR12DE an\f HR15DE engine mo\fels)
JVM0059XHR12DDR engine model
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-14Maintenance and do-it-yourself
Engine oil and filter replacement \fK9K engine
model)
\bDI2472
1. Oil drain plug
2. Oil filter
1. Place a large drain pan under the drain plug.
2. Remove the drain plug with a wrench.
3. Remove the oil filler cap and completely drain the oil.
If the oil filter is to be changed, remove and
replace it at this time.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
4. Loosen the oil filter with an oil filter wrench.
5. Remove the oil filter by turning it by hand.
6. Wipe the entire oil filter mounting surface with aclean cloth.
Be sure to remove any old gasket remaining on the
mounting surface. 7. Apply new engine oil to the gasket on the new oil
filter.
8. \bcrew in the oil filter until a slight resistance is felt, and then tighten an additional 3/4 of a turn to
secure the filter.
Oil filter tightening torque:16 to 20 N·m (1.6 to 2.0 kg-m, 12 to 15 ft-lb)
9. Clean and reinstall the drain plug and new washer. \becurely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:16 to 24 N·m (1.6 to 2.4 kg-m, 12 to 18 ft-lb)
10. Refill the recommended engine oil and quantity. \f\bee “Recommended fuel/lubricants and capaci-
ties” \fP.9-2) .)
11. \becurely install the oil filler cap.
12. \btart the engine.
13. Check the drain plug and the oil filter for any sign of leakage.
14. Dispose of the used oil in the proper manner. Check your local regulations.
15. Check the engine oil level according to the proper procedure. \f\bee “Checking engine oil level” \fP.8-
10) .)
After operation
1. Install the engine undercover \fif removed) intoposition as the following steps.
a. Pull the center of each plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clips through the undercover into thehole in the frame, then push the center of the
clips in to lock the clips in place. d. \bcrew in the bolts, then tighten them.
2. Lower the vehicle carefully to the ground.
PROTECT ENVIRONMENT
It is illegal to pollute drains, watercourses and soil. Use
authorized waste collection facilities, including civil
amenity sites and garages providing facilities for
disposal of used oil and used oil filters. If in doubt,
contact your local authority for advice on disposal.
The regulations concerning the pollution of the
environment will vary from country to country.
&RQGLWLRQ