2012 RENAULT PULSE radio


> (GLW    0RGHO .$2(0B5HQDXOW @
4-50Heater and air conditioner, and audio system
2. Push and hold a radio memor\f button*1-*6until a beep sounds. \bThe radio mutes when the
memor\f button is pushed.)
3. The channel indicator will displa\f and the radio mute disengages, indicating that the memor\f is
stored properl\f.
4. Perform steps 1 - 3 for all other memor\f buttons.
If the batter\f cable is disconnected, or if the audio fuse
blows, the radio memor\f will be erased. If this occurs,
reset the desired stations.
USB memor\f device operation
Audio main operation:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) .
Open the lid and connect a USB memor\f device into
the connector. The s\fstem will switch to the USB
memor\f device mode automaticall\f.
If the s\fstem is turned off while the USB memor\f
device is pla\fing, pushing the
dial will start the
USB memor\f device.
If the USB memor\f device cannot be pla\fed, one of the
following messages will be displa\fed.
. “USB memor\f device not supported”
. “No audio file detected”
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
.Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
(Some USB devices come with a
mark as a guide. Make sure that the mark
is facing the correct direction before insert-
ing the device.)
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to \four device manufacturer’s owner information
regarding the proper use and care of the device.
AUX button:
To operate the USB memor\f device use one of the
following methods:
. Push the
button then turn the TUNE/MENU/
ENTER dial to select the USB item. Once high-
lighted, push the TUNE/MENU/ENTER dial.
. Push the
button repeatedl\f until USB is
highlighted, and then push the TUNE/MENU/
ENTER dial.
Operation buttons:
The following operations are identical to the audio main
operation of the Compact Disc \bCD) operation. For
details, see “CD pla\fer operation” \bP.4-48) . .
List view
. Quick search
.
. MIX \bRandom pla\f)
. RPT \bRepeat track)
. Folder browsing
DISP button:
While a track with recorded music information tags
\bID3-tags) is being pla\fed, the title of the pla\fed track
is displa\fed. If the tags are not provided, a notification
message is displa\fed.
When the
button is pushed repeatedl\f, further
information about the track can be displa\fed along
with the track title as follows:
Track time ?Artist ?Album ?Folder name ?Track
time
Track details:
B\f pushing and holding the
button the displa\f will
show a detailed overview and after a few seconds it
will return to the main displa\f. Push the
button
briefl\f to return to the main displa\f immediatel\f.
iPod pla\fer operation
Connecting iPod:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) . Open
the USB connector lid and connect the iPod cable to
the USB connector. The batter\f of the iPod is charged
while the device is connected to the vehicle.
Depending on the version of the iPod, the displa\f on
the iPod shows a RENAULT or Accessor\f Attached
screen when the connection is completed. When the
iPod is connected to the vehicle, the iPod music librar\f
can onl\f be operated b\f the vehicle audio controls.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
displayed (top left of the display): Signal strength
()\f Battery status* () and BluetoothŠ\bON”
().
*: If the low battery message comes on\f the BluetoothŠ
device must be recharged soon.
The pairing procedure and operation may vary
according to device type and compatibility. See the
owner’s manual of the Bluetooth
Šdevice for further
details.
Select Device:
The paired device list shows which Bluetooth
Šaudio
or cellular phone devices have been paired or
registered with the Bluetooth
Šaudio system. If the list
contains devices\f select the appropriate device to
connect to the Bluetooth
Šaudio system.
The following symbols indicate the capability of the
registered device:
.
: cellular phone integration
.
: Audio streaming (A2DP- Advanced Audio
Distribution Profile)
Delete Device:
A registered device can be removed from the Blue-
tooth
Šaudio system. Select a registered device then
push the TUNE/MENU/ENTER dial to confirm deletion.
Bluetooth:
If Bluetooth
Šhas been switched off\f a notification
message On/Off appears when you select \bBluetooth”
from the setup menu screen\f or push the
button.
To turn the BluetoothŠsignal on\f push the TUNE/
MENU/ENTER dial and a follow up screen will appear.
Select \bOn” and push the TUNE/MENU/ENTER dial to
display the Bluetooth
Šsettings menu screen. Bluetooth
Šaudio streaming main operation:
Place the ignition switch in the \bACC” or \bON”
position. If the audio system is turned off while the
Bluetooth
Šaudio is playing\f pushing thedial will
start BluetoothŠaudio streaming.
AUX button:
To operate BluetoothŠaudio streaming use one of the
following methods:
. Push the
button\f then turn the TUNE/MENU/
ENTER dial to highlight BT Audio\f and push the
TUNE/MENU/ENTER dial.
. Push the
button repeatedly until BT Audio is
highlighted\f then push the TUNE/MENU/ENTER
dial.
The type of display\f
*Aor*B\f shown on the audio
system can vary depending on the BluetoothŠversion
of the device.
Fast Forward/Rewind buttons:
Fast Forward\f Fast Reverse:
When the
/button is pushed continuously\f
the track will be played at high speed. When the button
is released\f the track will be played at normal playing
speed.
Track up/down: By pushing the
/button once\f the track will
be skipped forward to the next track or backward to
the beginning of the current played track. Push the
/button more than once to skip through the
tracks.
DISP button:
If the song contains music information tags (ID3-tags) \f
the title of the played song will be displayed. If tags are
not provided\f the display will not show any messages.
When the
button is pushed repeatedly\f further
information about the song can be displayed along
with the song title.
By pushing and holding the
button the display will
show a detailed overview which after a few seconds
will return to the main display. Push the
button
briefly to return to the main display immediately.
Radio Broadcast data system (RBDS)
The RBDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RBDS provides information services such as station
name\f traffic information\f and news.
NOTE:
In some countries or regions, some of these
services may not be available.
Alternative Frequency (AF) mode:
The AF mode operates in the FM (radio) mode.
. The AF mode operates both in the FM (radio) and
CD mode (if FM was previously selected in the
radio mode) .
. The AF function compares signal strengths and
selects the station with the optimum reception
conditions for the currently tuned-in station.
Heater and air conditioner, and audio system4-53
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-54Heater and air conditioner, and audio system
RBDS functions
Programme Service (PS) function (station name
display function):
When an RBDS station is tune\f in with seek or \banual
tuning, the RBDS \fata is receive\f an\f the PS na\be is
\fisplaye\f.
FM-AM RADIO WITH COMPACT DISC (CD)
PLAYER AND NAVIGATION (if equippe\f)
SAA2589
For \fetails, see the separately provi\fe\f Navigation
Owner’s Manual.
CD/USB MEMORY (if equippe\f) CARE AND
CLEANING
CD
SAA0451
.Han\fle a \fisc by its e\fges. Never touch the
surface of the \fisc. Do not ben\f the \fisc.
. Always place the \fiscs in the storage case when
they are not being use\f.
. To clean a \fisc, wipe the surface fro\b the center
to the outer e\fge using a clean, soft cloth. Do not
wipe the \fisc using a circular \botion.
Do not use a conventional recor\f cleaner or
alcohol inten\fe\f for in\fustrial use.
. A new \fisc \bay be rough on the inner an\f outer
e\fges. Re\bove the rough e\fges by rubbing the
inner an\f outer e\fges with the si\fe of a pen or
pencil as illustrate\f.
USB \be\bory \fevice (if equippe\f)
.Do not touch the ter\binal portion of the USB
\be\bory \fevice.
. Do not place heavy objects on the USB \be\bory
\fevice.
. Do not store the USB \be\bory \fevice in highly
hu\bi\f locations.
. Do not expose the USB \be\bory \fevice to \firect
sunlight.
. Do not spill any liqui\fs on the USB \be\bory
\fevice.
Refer to the USB \be\bory \fevice Owner’s Manual for
the \fetails.
STEERING WHEEL SWITCH FOR AUDIO
CONTROL (if equippe\f)
JVH0512XType A
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVH0005XType B1. SOURCE select s\fitch
2. V\blume c\bntr\bl s\fitch
3. Tuning s\fitch
The audi\b system can be \bperated using the c\bntr\bls
\bn the steering \fheel.
SOURCE select s\fitch
Push the SOURCE select s\fitch t\b change the m\bde
t\b available audi\b s\burce.
V\blume c\bntr\bl s\fitch
Push up \br d\b\fn the v\blume c\bntr\bl s\fitch t\b increase
\br decrease the v\blume.
Tuning s\fitch
Memory change (radio):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
change the next \br previ\bus radi\b preset.
SEEK tuning (radio):
Push the tuning s\fitch f\br m\bre than 1.5 sec\bnds t\b
seek the next \br previ\bus radi\b stati\bn. APS (Automatic Program Search) FF, APS REW
(CD):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
return t\b the beginning \bf the present pr\bgram \br skip
t\b the next pr\bgram. Push several times t\b skip back \br
skip thr\bugh pr\bgrams.
This system searches f\br the blank intervals bet\feen
selecti\bns. If there is a blank interval \fithin \bne
pr\bgram \br there is n\b interval bet\feen pr\bgrams,
the system may n\bt st\bp in the desired \br expected
l\bcati\bn.
Type A:
JVH0007X
The USB/AUX c\bnnect\br is \bn the l\b\fer center \bf the
instrument panel.
F\br details, see the separately pr\bvided Navigati\bn
O\fner’s Manual.
Type B:
JVH0731X
The USB/AUX c\bnnect\br is l\bcated \bn the instrument
panel. F\br details, see “USB mem\bry device \bperati\bn”
(P.4-50) , “iP\bd player \bperati\bn” (P.4-50) \br “Audi\b
main \bperati\bn” (P.4-47) .
Heater and air conditioner, and audio system4-55
USB/AUX CONNECTOR (if
equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-56Heater and air conditioner, and audio system
When installing a CB, ham ra\fio or a car phone in \bour
vehicle, be sure to observe the following cautions,
otherwise the new equipment ma\b a\fversel\b affect the
Engine Control S\bstem an\f other electronic parts.
CAUTION:
.Keep the antenna as far away as possible
from the Electronic Control Module.
. Keep the antenna wire at least 20 cm (8 in)
away from the Engine Control harnesses. Do
not route the antenna wire next to any
harnesses.
. Adjust the antenna standing wave ratio as
recommended by the manufacturer.
. Connect the ground wire from the radio
chassis to the body.
. For details, consult a RENAULT dealer.
WARNING:
.Use a phone after stopping your vehicle in a
safe location. If you have to use a phone
while driving, exercise extreme caution at all
times so full attention may be given to
vehicle operation.
. If a conversation in a moving vehicle re-
quires you to take notes, pull off the road to
a safe location and stop your vehicle before
doing so.
CAUTION:
To avoid draining the vehicle battery, use a
phone after starting the engine.
For mo\fel with navigation s\bstem, see the separatel\b
provi\fe\f Navigation Owner’s Manual.
Your vehicle is equippe\f with the Bluetooth
ŠHan\fs-
Free Phone S\bstem. If \bou are an owner of a
Bluetooth
Šenable\f cellular phone, \bou can set up
the wireless connection between \bour cellular phone
an\f the in-vehicle phone mo\fule. With Bluetooth
Š
wireless technolog\b, \bou can make or receive a han\fs-
free telephone call with \bour cellular phone in the
vehicle.
Once \bour cellular phone is paire\f to the in-vehicle
phone mo\fule, no other phone connecting proce\fure
is require\f. Your phone is automaticall\b connecte\f with
the in-vehicle phone mo\fule when the ignition switch
is place\f in the “ON” position with the paire\f cellular
phone turne\f on an\f carrie\f in the vehicle.
You can register up to 5 \fifferent Bluetooth
Šcellular
phones to the in-vehicle phone mo\fule. However, \bou
can talk on onl\b one cellular phone at a time.
Before using the Bluetooth
ŠHan\fs-Free Phone S\bstem, refer to the following notes.
.
Set up the wireless connection between a cellular
phone an\f the in-vehicle phone mo\fule before
using the s\bstem.
. Some Bluetooth
Šenable\f cellular phones ma\b not
be recognize\f b\b the in-vehicle phone mo\fule.
. You will not be able to use a han\fs-free phone
un\fer the following con\fitions.
— Your vehicle is outsi\fe of the telephone service
area.
— Your vehicle is in an area where it is \fifficult to receive ra\fio waves; such as in a tunnel, in an
un\fergroun\f parking garage, near a tall buil\f-
ing or in a mountainous area.
— Your cellular phone is locke\f to prevent it from being \fiale\f.
When the ra\fio wave con\fition is not i\feal or ambient
soun\f is too lou\f, it ma\b be \fifficult for the other part\b
to hear \bour voice \furing a call. Please close the
win\fows if possible.
Do not place the cellular phone in an area surroun\fe\f
b\b metal or far awa\b from the in-vehicle phone mo\fule
to prevent tone qualit\b \fegra\fation an\f wireless
connection \fisruption.
While a cellular phone is connecte\f through the
Bluetooth
Šwireless connection, the batter\b power of
the cellular phone ma\b \fischarge quicker than usual.
The Bluetooth
ŠHan\fs-Free Phone S\bstem cannot
charge cellular phones.
Refer to the cellular phone Owner’s Manual regar\fing
the telephone charges, cellular phone antenna an\f
bo\f\b, etc.
This wireless han\fs-free s\bstem is base\f on Blue-
tooth
Štechnolog\b.
CAR PHONE OR CB RADIO Bluetooth
ŠHANDS-FREE PHONE
SYSTEM (if equipped for model
without navigation system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.Frequency: 2402 MHz - 2480 MHz
. Out\fut Power: 4\b14 dBm EIRP
. Modulation: FHSS GFSK 8DPSK, \f/4DQPSK
. Number of Channel: 79
. This wireless equi\fment cannot be used for any
services related to safety due to the \fossibility of
radio interference
REGULATORY INFORMATION
BluetoothŠis a trademark owned
by Bluetooth SIG, Inc\b and li-
censed to Clarion Co\b, Ltd\b and
Daewoo IS Cor\f\b
CE STATEMENT
Hereby “Yangfeng Visteon Automotive Electronics Co\b,
Ltd\b” and “Clarion Cor\foration” declares that this
Bluetooth car kit AV System is in com\fliance with the
essential requirements and other relevant \frovisions of
Directive 1999/5/EC\b
HANDS-FREE TELEPHONE OPERATION
(Ty\fe A)
JVH0006XFor Europe
JVH0046XFor South Africa1\b PHONE SEND button
2\b PHONE END/BACK button
3\b PHONE BOOK button
The following o\ftions can be selected:
. Paired list
. Pair \fhone
. Delete \fhone
. Bluetooth
Šconnection .
Delete \fhone book
. My number
Pairing \frocedure
If you wish to make a BluetoothŠconnection for the
first time between your mobile \fhone and the Blue-
tooth
Šsystem of the audio unit, \ferform the following
\fairing \frocedure\b
1\b Place the ignition switch in the “ACC” \fosition\b
2\b Switch on the audio system and your mobile \fhone\b
For the vehicle:
1\b Briefly \fush the MENU button\b
2\b Push the ENTER button\b
3\b Turn the MENU/VOL dial and select PAIR PHONE then \fush the ENTER button\b
4\b The dis\flay shows READY TO PAIR then PASS- CODE=1234\b
On the mobile \fhone:
1\b Activate the Bluetooth
Šconnection\b
2\b Activate the search mode for BluetoothŠequi\f-
ment\b Refer to the owner’s manual of your mobile
\fhone for further details\b If the search mode finds
the device, it will be shown on your mobile \fhone
dis\flay\b
3\b Select the device name MY CAR\b
4\b Enter the \fasscode number 1234 as shown on the dis\flay of the audio unit with the key\fad on
your mobile \fhone and then \fush the confirmation
button on your mobile \fhone\b
Heater and air conditioner, and audio system4-57
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.make a call via voice dialling by pushing thebutton \for more than 2 seconds then say
the voice tag clearly.
\bANDS-FREE TELEP\bONE OPERATION
(Type B)
JV\b0519X
Buttons:
1. Phone button
2. A-Z button
3. TUNE/MENU/ENTER dial
4. SETUP button
Microphone:
The microphone is located near the map light.
WARNING:
While driving, using the cellular phone is ex-
tremely dangerous because it significantly im-
pairs your concentration and diminishes your
reaction capabilities to sudden changes on the
road, and it may lead to a fatal accident. This
applies to all phone call situations such as when
receiving an incoming call, during a phone
conversation, when calling through the phone
book search, etc.
CAUTION:
Certain country or region jurisdictions prohibit
the use of the cellular phone in the car without
hands-free support.
This chapter provides in\formation about the RENAULT
hands-\free phone system using a Bluetooth
Šconnec-
tion.
Bluetooth
Šis a wireless radio communication stan-
dard. This system o\f\fers a hands-\free \feature \for your
cellular phone to enhance driving com\fort.
In order to use your cellular phone with the Bluetooth
Š
o\f the audio system, the cellular phone must \first be set
up. Once it has been set up, the hands-\free mode is
automatically activated on the registered cellular phone
(via Bluetooth
Š) when it comes into range.
A noti\fication message appears on the audio display
when the phone is connected, when an incoming call
is being received, as well as when a call is initiated.
When a call is active, the audio system and
microphone (located near the map light) enable
hands-\free communication.
I\f the audio system is in use at the time, the radio, CD,
or AUX source mode will be muted and will stay muted
until the active call has ended.
The Bluetooth
Šsystem may not be able to connect
with your cellular phone \for the \following reasons:
. The cellular phone is too \far away \from the vehicle.
. The Bluetooth
Šmode on the cellular phone has
not been activated.
. The cellular phone has not been paired with the
Bluetooth
Šsystem o\f the audio unit.
. The cellular phone does not support BluetoothŠ
technology (BT Core v1.2, \bands Free Pro\file v1.0
and Object Push Pro\file v1.0) . NOTE:
For details, see the cellular phone’s owner’s
manual.
\bands-\free phone setup
To set up the BluetoothŠsystem to pair with (connect
or register) a pre\ferred cellular phone, push the
button, select the BluetoothŠkey, and then push the
TUNE/MENU/ENTER dial. It is also possible to display
the set up menu directly by pushing the
button.
. Pair Device
Bluetooth
Šcellular phones can be paired with the
system. A maximum o\f 5 cellular phones can be
registered.
. Select Device
Paired Bluetooth
Šcellular phones are listed on the
display and can be selected \for connection.
. Delete Device
A registered Bluetooth
Šcellular phone can be
deleted.
. Bluetooth
I\f this setting is turned o\f\f, the connection between
the Bluetooth
Šdevices and the in-vehicle Blue-
toothŠmodule will be cancelled.
When success\fully paired, a noti\fication message will
be displayed. During the connection the \following
status icons will be displayed (top le\ft o\f display):
Signal strength (
) , Battery status () and
BluetoothŠ().
*: I\f the low battery message comes on, the BluetoothŠ
device must be recharged soon.
Heater and air conditioner, and audio system4-63
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.If the vehicle battery is discharged, the
ignition switch cannot be switched from
the “LOCK” position, and if the steering lock
is engaged, the steering wheel cannot be
moved. Charge the battery as soon as
possible. (See “Jump starting” (P.6-8) .)
Operating range
SSD0436
The Intelligent \fey can only \be used for starting the
engine when the Intelligent \fey is within the specified
operating range
*1.
When the Intelligent \fey \battery is almost discharged
or strong radio waves are present near the operating
location, the Intelligent \fey system’s operating range
\becomes narrower and may not function properly.
If the Intelligent \fey is within the operating range, it is
possi\ble for anyone, even someone who does not carry
the Intelligent \fey, to push the ignition switch to start
the engine.
. The luggage room area is not included in the
operating range, \but the Intelligent \fey may
function.
. If the Intelligent \fey is placed on the instrument
panel, inside the glove \box, door pocket or the
corner of the interior compartment, the Intelligent \fey may not function.
. If the Intelligent \fey is placed near the door or
window outside the vehicle, the Intelligent \fey
may function.
Automatic transmission (AT)/Continuously
Varia\ble Transmission (CVT) model
The ignition lock is designed so that the ignition switch
cannot \be switched to the “LOC\f” position until the
selector lever is moved to the “P” (Park) position.
When pushing the ignition switch to the “OFF”
position, make sure the selector lever is in the “P”
(Park) position.
Type A (model with dot matrix display):
When the ignition switch cannot \be switched to the
“LOC\f” position:
1. SHIFT “P” warning appears on the dot matrix
display (in the vehicle information display) and a
chime sounds.
2. Move the selector lever to the “P” (Park) position.
3. If the ignition switch is in the “ACC” position, the “PUSH” warning appears on the dot matrix
display.
4. Push the ignition switch. The ignition switch is switched to the “ON” position.
5. The “PUSH” warning appears again on the dot matrix display.
6. Push the ignition switch. The ignition switch is switched to the “OFF” position.
7. Open the door. The ignition switch will change to the “LOC\f” position.
For warnings and indicators on the Vehicle information
display, see “Vehicle information display” (P.2-20) . Type B (model without dot matrix display) :
1. Move the selector lever to the “P” (Park) position.
2. Push the ignition switch to the “OFF” position.
3. Open the door. The ignition switch will change to
the “LOC\f” position.
If the ignition switch is switched to the “LOC\f”
position, the selector lever cannot \be moved from the
“P” (Park) position. The selector lever can \be moved if
the ignition switch is in the “ON” position with the foot
\brake depressed.
STEERING LOC\f
The ignition switch is equipped with an anti-theft
steering lock device.
To lock steering wheel
1. Push the ignition switch to the “OFF” position where the ignition switch position indicator will not
illuminate.
2. Open or close the door. The ignition switch turns to the “LOC\f” position.
3. Turn the steering wheel 1/6 of a turn to the right or left from the straight up position.
To unlock steering wheel
Push the ignition switch, and the steering wheel will \be
automatically unlocked.
CAUTION:
.If the battery of the vehicle is discharged, the
push-button ignition switch cannot be
switched from the “LOCK” position.
. If the ignition switch position does not
change from the “LOCK” position, push the
ignition switch again while rotating the
Starting and driving5-7
&RQGLWLRQ