2012 RENAULT PULSE AUX


> (GLW    0RGHO .$2(0B5HQDXOW @
Audio main operation
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
Power/VOL dial:
Power ON/OFF:
To turn on the audio system, push the
dial.
. The system will turn on in the mode, which was
used immediately before the system was turned
off.
. If a CD is inserted or a USB and/or an AUX device
is connected when the system is turned off, and if
the system is turned on again with the devices
removed or disconnected, the radio will turn on.
To turn off the audio system, push the
dial.
Volume control:
To control the volume, turn the
dial.
Turn the
dial clockwise to make the sound louder.
Turn the
dial counterclockwise to make the sound
quieter.
SETUP button:
To configure Audio, Clock, Bluetooth, Language or
Scroll direction settings, perform the following proce-
dure:
1. Push the
button.
2. Push the TU\bE/ME\bU/E\bTER dial.
3. Turn the TU\bE/ME\bU/E\bTER dial clockwise or counterclockwise. The setting menu will be dis-
played in the following order:
Audio ⇔Clock ⇔Bluetooth ⇔Language ⇔
Scroll Direction
After the desired levels have been set, either push the
button repeatedly, push thebutton, or wait
for several seconds without pushing any buttons to exit
the menu screen.
Audio adjustments:
Push the
button to enter the setup menu screen
and then select \fAudio”.
Each time the TU\bE/ME\bU/E\bTER dial is pushed, the
mode will change as follows:
BASS ?TREBLE ?BALA\bCE ?FADE ?AUX
VOL ?SPD VOL (if equipped) ?Audio (setup menu
screen) ?BASS
Turn the TU\bE/ME\bU/E\bTER dial clockwise or
counterclockwise to adjust the following items and
push the TU\bE/ME\bU/E\bTER dial to confirm.
Bass control:
Use this control to enhance or attenuate the bass
response sound.
Treble control:
Use this control to enhance or attenuate the treble.
Balance control:
Use this control to adjust the balance of the volume
between the left and right speakers.
Fader control:
Use this control to adjust the balance of the volume
between the front and rear speakers (if equipped) .
AUX VOL (Auxiliary volume) control:
Use this control to adjust the volume output from the
auxiliary source.
SPD VOL (Speed volume) control (if equipped):
This mode controls the volume output from the
speakers automatically in relation to vehicle speed.
Adjusting the setting to \f0” (zero) turns off the speed volume feature.
Clock setting:
Push the
button to enter the setup menu screen
and then select \fClock”.
Turn the TU\bE/ME\bU/E\bTER dial, the mode will
change as follows:
Set Time ⇔O\b/OFF ⇔Clock Format ⇔Set Time
Set Time:
Select \fSet Time” then adjust the clock as follows:
The hour display will start flashing. Turn the TU\bE/
ME\bU/E\bTER dial to adjust the hour and push the
TU\bE/ME\bU/E\bTER dial. The minute display will start
flashing. Turn the TU\bE/ME\bU/E\bTER dial to adjust
the minute and push the TU\bE/ME\bU/E\bTER dial to
finish the clock adjustment.
O\b/OFF:
Set the clock display to on or off when the audio unit is
turned off. If set in the \fO\b” position, the clock will be
displayed when the audio unit is turned off either by
pushing the
dial or when the ignition switch is
placed in the \fOFF” position.
Clock Format:
Switch the clock display between 24-hour and 12-
hour clock mode.
Bluetooth setting:
It is possible to set the Bluetooth settings. (See
\fBluetooth
Šaudio player operation” (P.4-52) .)
Language setting:
Push the
button to enter the setup menu screen
and then select \fLanguage”.
Select the appropriate language and push the TU\bE/
ME\bU/E\bTER dial. Upon completion, the screen will
automatically adopt the language setting.
Heater and air conditioner, and audio system4-47
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-48Heater and air conditioner, and audio system
Scroll direction:
Set the scrolling behavior of the \fUNE\bMENU\bEN\fER
dial to scroll UP or DOWN.
Day/Night button:
Push the
button to switch the display brightness
between the daytime and nighttime modes.
AUX button:
\fhe AUX IN jack is located on the instrument panel. For
details, see “USB\bAUX connector” (P.4-55) . \fhe AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, digital audio player or laptop computer.
Push the
button to play a compatible device when
it is plugged into the AUX IN jack.
RENAUL\f strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
monaural cable is used.
CD player operation
JVH0509X
\fhe audio system operates when the ignition switch is in the “ACC” or “ON” position.
Loading:
Insert a CD into the slot with the label side facing up.
\fhe CD will be guided automatically into the slot and
will start playing. After loading the CD, the number of
tracks and the playtime will appear on the display.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
NOTE:
.
The CD player accepts normal audio CDs or
CDs containing MP3/WMA files.
. The audio unit will automatically detect if a
CD containing MP3/WMA files is inserted,
and [MP3CD] will be indicated.
. An error notification message will be dis-
played when an incompatible disc (e.g. DVD)
is inserted, or if the player cannot read the
CD. Eject the disc and insert another disc.
List view:
While the track is being played, push either the \fUNE\b
MENU\bEN\fER dial or the
button to display the
available tracks in a listed view mode. \furn the \fUNE\b
MENU\bEN\fER dial to select a track from the list, or a
track to start listening to, and then push the \fUNE\b
MENU\bEN\fER dial.
Quick search:
In the list view mode, a quick search can be performed
to find a track from the list. Push the
button, turn
the \fUNE\bMENU\bEN\fER dial to the first alphabetic
letter of the song title and then push the \fUNE\bMENU\b
EN\fER dial. When found, a list of the available songs
will be displayed. Select, and push the \fUNE\bMENU\b EN\fER dial to play the preferred track.
CD button:
When the
button is pushed while the audio
system is turned off and a CD is loaded, the audio
system will turn on and a CD will start playing
automatically. If the radio or AUX source mode is
already playing, it will automatically turn off and the CD
will start playing.
However, if the CD is not loaded, then a notification
message will be displayed and the audio unit will
remain in the radio or AUX source mode.
Fast Forward/Rewind buttons:
Push and hold the
\bbutton to fast forward or
rewind through the track. When the button is released,
the track will play at normal playing speed.
\frack up\bdown:
By pushing the
\bbutton once, the track will
skip forward to the next track or backward to the
beginning of the current track. Push the
\bbutton more than once to skip through the tracks.
Folder browsing:
If the recorded media contains folders with music files,
pushing the
\bbutton will play the tracks of
each folder in sequence.
\fo select a preferred folder:
1. Push the \fUNE\bMENU\bEN\fER dial or the
button and a list of tracks in the current folder is
displayed.
2. Push the
button.
3. \furn the \fUNE\bMENU\bEN\fER dial to highlight the preferred folder.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-50Heater and air conditioner, and audio system
2. Push and hold a radio memor\f button*1-*6until a beep sounds. \bThe radio mutes when the
memor\f button is pushed.)
3. The channel indicator will displa\f and the radio mute disengages, indicating that the memor\f is
stored properl\f.
4. Perform steps 1 - 3 for all other memor\f buttons.
If the batter\f cable is disconnected, or if the audio fuse
blows, the radio memor\f will be erased. If this occurs,
reset the desired stations.
USB memor\f device operation
Audio main operation:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) .
Open the lid and connect a USB memor\f device into
the connector. The s\fstem will switch to the USB
memor\f device mode automaticall\f.
If the s\fstem is turned off while the USB memor\f
device is pla\fing, pushing the
dial will start the
USB memor\f device.
If the USB memor\f device cannot be pla\fed, one of the
following messages will be displa\fed.
. “USB memor\f device not supported”
. “No audio file detected”
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
.Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
(Some USB devices come with a
mark as a guide. Make sure that the mark
is facing the correct direction before insert-
ing the device.)
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to \four device manufacturer’s owner information
regarding the proper use and care of the device.
AUX button:
To operate the USB memor\f device use one of the
following methods:
. Push the
button then turn the TUNE/MENU/
ENTER dial to select the USB item. Once high-
lighted, push the TUNE/MENU/ENTER dial.
. Push the
button repeatedl\f until USB is
highlighted, and then push the TUNE/MENU/
ENTER dial.
Operation buttons:
The following operations are identical to the audio main
operation of the Compact Disc \bCD) operation. For
details, see “CD pla\fer operation” \bP.4-48) . .
List view
. Quick search
.
. MIX \bRandom pla\f)
. RPT \bRepeat track)
. Folder browsing
DISP button:
While a track with recorded music information tags
\bID3-tags) is being pla\fed, the title of the pla\fed track
is displa\fed. If the tags are not provided, a notification
message is displa\fed.
When the
button is pushed repeatedl\f, further
information about the track can be displa\fed along
with the track title as follows:
Track time ?Artist ?Album ?Folder name ?Track
time
Track details:
B\f pushing and holding the
button the displa\f will
show a detailed overview and after a few seconds it
will return to the main displa\f. Push the
button
briefl\f to return to the main displa\f immediatel\f.
iPod pla\fer operation
Connecting iPod:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) . Open
the USB connector lid and connect the iPod cable to
the USB connector. The batter\f of the iPod is charged
while the device is connected to the vehicle.
Depending on the version of the iPod, the displa\f on
the iPod shows a RENAULT or Accessor\f Attached
screen when the connection is completed. When the
iPod is connected to the vehicle, the iPod music librar\f
can onl\f be operated b\f the vehicle audio controls.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
* iPod and iPhone are trademarks of Apple In\f.,
registered in the \b.S. and other \fountries.
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
.Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
(Some USB devices come with a
mark as a guide. Make sure that the mark
is facing the correct direction before insert-
ing the device.)
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your devi\fe manufa\fturer’s owner information
regarding the proper use and \fare of the devi\fe.
Compatibility:
The following models are supported:
. Third generation iPhone (Firmware version
IOS4/4.0)
. Fourth generation iPhone (Firmware version
IOS4/4.0) .
Fifth generation iPod (Firmware version 1.3)
. First generation iPod Classi\f (Firmware version
1.1.1 or 1.1.2PC)
. Se\fond generation iPod Classi\f (Firmware ver-
sion 2.0.1)
. First generation iPod tou\fh (Firmware version
1.1.5 or 2.2.1)
. Se\fond and third generation iPod tou\fh (Firm-
ware version 2.2.1 or IOS4/4.0.0)
. First generation iPod nano (Firmware version
1.3.1)
. Se\fond generation iPod nano (Firmware version
1.1.3)
. Third generation iPod nano (Firmware version
1.1.2PC or 1.1.3PC)
. Fourth generation iPod nano (Firmware version
1.0.2 or 1.0.4)
. Fifth generation iPod nano (Firmware version 1.0.1
or 1.0.2)
The iPod tou\fh may not respond qui\fkly to the system
in some \fases.
Make sure that the iPod firmware is updated.
Operating tips:
. iPod Shuffle and iPod mini are not supported.
. Some iPod operations may not be available with
this system.
AUX button:
To operate the iPod use one of the following methods:
. Push the
button and then turn the T\bNE/
MEN\b/ENTER dial for the \bSB item. On\fe
highlighted, push the T\bNE/MEN\b/ENTER dial. .
Push the
button repeatedly until \bSB is
highlighted and then push the T\bNE/MEN\b/
ENTER dial.
Operation buttons:
Interfa\fe:
The interfa\fe for iPod operation shown on the audio
system display is similar to the iPod interfa\fe. \bse the
T\bNE/MEN\b/ENTER dial to play a tra\fk on the iPod.
The following items \fan be \fhosen from the menu list
s\freen.
. Playlists
. Artists
. Albums
. Tra\fks
. Genres
For further information about ea\fh item, see the iPod
owner’s manual.
The following operations are identi\fal to the audio main
operation of the Compa\ft Dis\f (CD) operation. For
details, see “CD player operation” (P.4-48) .
. List view
. Qui\fk sear\fh
.
. MIX (Random play)
. RPT (Repeat tra\fk)
. Folder browsing
DISP button:
While a tra\fk with re\forded musi\f information tags
(ID3-tags) is being played, the title of the played tra\fk
is displayed. If the tags are not provided then a
notifi\fation message is displayed.
When the
button is pushed repeatedly, further
Heater and air conditioner, and audio system4-51
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
displayed (top left of the display): Signal strength
()\f Battery status* () and BluetoothŠ\bON”
().
*: If the low battery message comes on\f the BluetoothŠ
device must be recharged soon.
The pairing procedure and operation may vary
according to device type and compatibility. See the
owner’s manual of the Bluetooth
Šdevice for further
details.
Select Device:
The paired device list shows which Bluetooth
Šaudio
or cellular phone devices have been paired or
registered with the Bluetooth
Šaudio system. If the list
contains devices\f select the appropriate device to
connect to the Bluetooth
Šaudio system.
The following symbols indicate the capability of the
registered device:
.
: cellular phone integration
.
: Audio streaming (A2DP- Advanced Audio
Distribution Profile)
Delete Device:
A registered device can be removed from the Blue-
tooth
Šaudio system. Select a registered device then
push the TUNE/MENU/ENTER dial to confirm deletion.
Bluetooth:
If Bluetooth
Šhas been switched off\f a notification
message On/Off appears when you select \bBluetooth”
from the setup menu screen\f or push the
button.
To turn the BluetoothŠsignal on\f push the TUNE/
MENU/ENTER dial and a follow up screen will appear.
Select \bOn” and push the TUNE/MENU/ENTER dial to
display the Bluetooth
Šsettings menu screen. Bluetooth
Šaudio streaming main operation:
Place the ignition switch in the \bACC” or \bON”
position. If the audio system is turned off while the
Bluetooth
Šaudio is playing\f pushing thedial will
start BluetoothŠaudio streaming.
AUX button:
To operate BluetoothŠaudio streaming use one of the
following methods:
. Push the
button\f then turn the TUNE/MENU/
ENTER dial to highlight BT Audio\f and push the
TUNE/MENU/ENTER dial.
. Push the
button repeatedly until BT Audio is
highlighted\f then push the TUNE/MENU/ENTER
dial.
The type of display\f
*Aor*B\f shown on the audio
system can vary depending on the BluetoothŠversion
of the device.
Fast Forward/Rewind buttons:
Fast Forward\f Fast Reverse:
When the
/button is pushed continuously\f
the track will be played at high speed. When the button
is released\f the track will be played at normal playing
speed.
Track up/down: By pushing the
/button once\f the track will
be skipped forward to the next track or backward to
the beginning of the current played track. Push the
/button more than once to skip through the
tracks.
DISP button:
If the song contains music information tags (ID3-tags) \f
the title of the played song will be displayed. If tags are
not provided\f the display will not show any messages.
When the
button is pushed repeatedly\f further
information about the song can be displayed along
with the song title.
By pushing and holding the
button the display will
show a detailed overview which after a few seconds
will return to the main display. Push the
button
briefly to return to the main display immediately.
Radio Broadcast data system (RBDS)
The RBDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RBDS provides information services such as station
name\f traffic information\f and news.
NOTE:
In some countries or regions, some of these
services may not be available.
Alternative Frequency (AF) mode:
The AF mode operates in the FM (radio) mode.
. The AF mode operates both in the FM (radio) and
CD mode (if FM was previously selected in the
radio mode) .
. The AF function compares signal strengths and
selects the station with the optimum reception
conditions for the currently tuned-in station.
Heater and air conditioner, and audio system4-53
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVH0005XType B1. SOURCE select s\fitch
2. V\blume c\bntr\bl s\fitch
3. Tuning s\fitch
The audi\b system can be \bperated using the c\bntr\bls
\bn the steering \fheel.
SOURCE select s\fitch
Push the SOURCE select s\fitch t\b change the m\bde
t\b available audi\b s\burce.
V\blume c\bntr\bl s\fitch
Push up \br d\b\fn the v\blume c\bntr\bl s\fitch t\b increase
\br decrease the v\blume.
Tuning s\fitch
Memory change (radio):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
change the next \br previ\bus radi\b preset.
SEEK tuning (radio):
Push the tuning s\fitch f\br m\bre than 1.5 sec\bnds t\b
seek the next \br previ\bus radi\b stati\bn. APS (Automatic Program Search) FF, APS REW
(CD):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
return t\b the beginning \bf the present pr\bgram \br skip
t\b the next pr\bgram. Push several times t\b skip back \br
skip thr\bugh pr\bgrams.
This system searches f\br the blank intervals bet\feen
selecti\bns. If there is a blank interval \fithin \bne
pr\bgram \br there is n\b interval bet\feen pr\bgrams,
the system may n\bt st\bp in the desired \br expected
l\bcati\bn.
Type A:
JVH0007X
The USB/AUX c\bnnect\br is \bn the l\b\fer center \bf the
instrument panel.
F\br details, see the separately pr\bvided Navigati\bn
O\fner’s Manual.
Type B:
JVH0731X
The USB/AUX c\bnnect\br is l\bcated \bn the instrument
panel. F\br details, see “USB mem\bry device \bperati\bn”
(P.4-50) , “iP\bd player \bperati\bn” (P.4-50) \br “Audi\b
main \bperati\bn” (P.4-47) .
Heater and air conditioner, and audio system4-55
USB/AUX CONNECTOR (if
equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.make a call via voice dialling by pushing thebutton \for more than 2 seconds then say
the voice tag clearly.
\bANDS-FREE TELEP\bONE OPERATION
(Type B)
JV\b0519X
Buttons:
1. Phone button
2. A-Z button
3. TUNE/MENU/ENTER dial
4. SETUP button
Microphone:
The microphone is located near the map light.
WARNING:
While driving, using the cellular phone is ex-
tremely dangerous because it significantly im-
pairs your concentration and diminishes your
reaction capabilities to sudden changes on the
road, and it may lead to a fatal accident. This
applies to all phone call situations such as when
receiving an incoming call, during a phone
conversation, when calling through the phone
book search, etc.
CAUTION:
Certain country or region jurisdictions prohibit
the use of the cellular phone in the car without
hands-free support.
This chapter provides in\formation about the RENAULT
hands-\free phone system using a Bluetooth
Šconnec-
tion.
Bluetooth
Šis a wireless radio communication stan-
dard. This system o\f\fers a hands-\free \feature \for your
cellular phone to enhance driving com\fort.
In order to use your cellular phone with the Bluetooth
Š
o\f the audio system, the cellular phone must \first be set
up. Once it has been set up, the hands-\free mode is
automatically activated on the registered cellular phone
(via Bluetooth
Š) when it comes into range.
A noti\fication message appears on the audio display
when the phone is connected, when an incoming call
is being received, as well as when a call is initiated.
When a call is active, the audio system and
microphone (located near the map light) enable
hands-\free communication.
I\f the audio system is in use at the time, the radio, CD,
or AUX source mode will be muted and will stay muted
until the active call has ended.
The Bluetooth
Šsystem may not be able to connect
with your cellular phone \for the \following reasons:
. The cellular phone is too \far away \from the vehicle.
. The Bluetooth
Šmode on the cellular phone has
not been activated.
. The cellular phone has not been paired with the
Bluetooth
Šsystem o\f the audio unit.
. The cellular phone does not support BluetoothŠ
technology (BT Core v1.2, \bands Free Pro\file v1.0
and Object Push Pro\file v1.0) . NOTE:
For details, see the cellular phone’s owner’s
manual.
\bands-\free phone setup
To set up the BluetoothŠsystem to pair with (connect
or register) a pre\ferred cellular phone, push the
button, select the BluetoothŠkey, and then push the
TUNE/MENU/ENTER dial. It is also possible to display
the set up menu directly by pushing the
button.
. Pair Device
Bluetooth
Šcellular phones can be paired with the
system. A maximum o\f 5 cellular phones can be
registered.
. Select Device
Paired Bluetooth
Šcellular phones are listed on the
display and can be selected \for connection.
. Delete Device
A registered Bluetooth
Šcellular phone can be
deleted.
. Bluetooth
I\f this setting is turned o\f\f, the connection between
the Bluetooth
Šdevices and the in-vehicle Blue-
toothŠmodule will be cancelled.
When success\fully paired, a noti\fication message will
be displayed. During the connection the \following
status icons will be displayed (top le\ft o\f display):
Signal strength (
) , Battery status () and
BluetoothŠ().
*: I\f the low battery message comes on, the BluetoothŠ
device must be recharged soon.
Heater and air conditioner, and audio system4-63
&RQGLWLRQ