2012 MITSUBISHI iMiEV clock setting

5-8 Comfort controls
5
Temperature control dial
N00736600235
Use this dial to adjust the temperature of the air flow from the
vents.
Turn the temperature control dial clockwise to make the air
warmer. Turn it counterclockwise to make the air cooler.
When the dial is set to middle (
) position, only uncooled and
unheated air will flow.
When the dial is moved to middle (
) position when using
cooling or heating, cooling or heating stops.NOTE
When the dial is moved from middle (
) position to the
left while the air conditioning is not operating, the air tem-
perature will not change.

When the dial is moved to middle (
) position and then to
the left while the air conditioning is operating, the air con-
ditioning system is operating again.
When the temperature control dial is set to “C” position,
the air selection will be automatically set to the
recirculation position and the air conditioning will oper-
ate.
When the dial is moved thereafter, the air conditioning
continues to operate and the air selection setting returns to
the setting before the dial was set to “C” position.
Mode selection dial
N00736700210
To change the position and amount of air flowing from the
vents, turn the mode selection dial. Refer to “Changing the
mode selection” on page 5-3.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-15
5
Defrosting or defogging (windshield, door windows)
N00731400557
To remove frost or fog from the windshield and door windows,
use the mode selection dial (“ ” or “ ”).For ordinary defrosting
Use this setting to keep the windshield and door windows clear
of mist, and to keep the leg area heated (when driving in rain or
snow).
1. Set the air selection switch (A) to the outside position.
2. Set the mode selection dial to the “ ” position.
3. Turn the temperature control dial clockwise or counter-
clockwise to the desired temperature between middle (
)
and “H” position.
4. Select the desired blower speed.
5. Push the air conditioning switch (B).
CAUTION
!
For safety, make sure you have a clear view through
all the windows.
BK0140800US.book 15 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-16 Comfort controls
5
For quick defrosting

1. Set the mode selection dial to the “ ” position.
2. Turn the temperature control dial clockwise or counter-
clockwise to the desired temperature between middle (
)
and “H” position.
3. Press the MAX switch (A).
NOTE
When the mode selection dial is set to the “ ” position,
the air conditioning compressor runs automatically. Out-
side air introduction will also be selected automatically.

When defrosting, do not set the temperature control dial to
the maximum cool position. This would blow cool air on
the window glass and fog it up.

Since defogging or defrosting with the MAX switch con-
sumes a large amount of power, stop the switch after
defogging or defrosting.
Use the MAX setting for a long time decreases the cruis-
ing range.
BK0140800US.book 16 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-41
5 Clock
(if so equipped)
N00755000124
The time is displayed when the electric motor switch is in the
“ON” or “ACC” position.To set the time1. Press and hold the clock button and the clock display
flashes.
2. Press the SEEK button to adjust the “hours” digit.
If you keep pressing the button, fast-forward begins.3. When the “hours” digit is adjusted, press the clock button
to flash the “minutes” digit.
Press the SEEK button to adjust the “minutes” digit.
If you keep pressing the button, fast-forward begins.
4. When the time is set, press the clock button to stop the
clock display from flashing.
NOTE
Reset the time after the 12V starter battery terminals are
disconnected and reconnected.

Seconds do not appear in the clock display, but after
adjusting the “minutes” setting, the clock begins to oper-
ate from 0 seconds.
A- Clock button
B- SEEK (clock adjustment up) button
C- SEEK (clock adjustment down) button
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分