2012 Lancia Flavia clock

WARNING!(Continued)
 Allowing children to be in a ve-
hicle unattended is dangerous for
a number of reasons. A child or
others could be seriously or fatally
injured. Children should be
warned not to touch the parking
brake, brake pedal or the shift
lever.
 Do not leave the key fob in or near
the vehicle, and do not leave the
ignition in the ACC or ON/RUN
position. A child could operate
power windows, other controls, or
move the vehicle.CAUTION!
An unlocked car is an invitation to
thieves. Always remove key from the
ignition and lock all doors when
leaving the vehicle unattended.
KEY-IN-IGNITION
REMINDER
Opening the driver's door when the
key is in the ignition sounds a signal to
remind you to remove the key. NOTE:
 The Key-In-Ignition reminder
only sounds when the ignition
key is placed in the LOCK or
ACC position.
 With either/both front doors open and a key in the ignition,
the power door lock buttons on
the interior trim panel are dis-
abled. This is an attempt to limit
locking the keys in the vehicle.
LOCKING THE DOORS
WITH THE KEY
There is only one external door lock
cylinder which is located in the driv-
er's door.
You can insert the key with either side
up. To lock the door, turn the key
clockwise. To unlock the door, turn
the key counterclockwise. For door
lock lubrication, see “Maintenance
Procedures” in “Maintaining Your Ve-
hicle” of this manual.
SENTRY KEY®
The Sentry Key® Immobilizer System
prevents unauthorized vehicle opera-
tion by disabling the engine. The sys- tem does not need to be armed or
activated. Operation is automatic, re-
gardless of whether the vehicle is
locked or unlocked.
The system uses ignition keys which
have an embedded electronic chip
(transponder) to prevent unauthor-
ized vehicle operation. Therefore,
only keys that are programmed to the
vehicle can be used to start and oper-
ate the vehicle. The system will shut
the engine off in two seconds if some-
one uses an invalid key to start the
engine.
NOTE:
A key which has not been pro-
grammed is also considered an in-
valid key, even if it is cut to fit the
ignition switch lock cylinder for
that vehicle.
During normal operation, after turn-
ing on the ignition switch, the Vehicle
Security Light will turn on for three
seconds for a bulb check. If the light
remains on after the bulb check, it
indicates that there is a problem with
the electronics. In addition, if the light
begins to flash after the bulb check, it
13

4
UNDERSTANDING YOUR INSTRUMENT
PANEL
 INSTRUMENT PANEL FEATURES . . . . . . . . . . . 105
 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . . . 106
 INSTRUMENT CLUSTER DESCRIPTIONS . . . . 107
 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . . . 115
 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) DISPLAYS . . . . . . . . . . . . . . 116
 OIL CHANGE REQUIRED . . . . . . . . . . . . . . . 117
 EVIC MAIN MENU . . . . . . . . . . . . . . . . . . . . . 117
 COMPASS DISPLAY . . . . . . . . . . . . . . . . . . . . 117
 AVERAGE FUEL ECONOMY (L/100KM) . . . . . 120
 DISTANCE TO EMPTY (DTE) . . . . . . . . . . . . . 120
 TIRE BAR . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
 ELAPSED TIME . . . . . . . . . . . . . . . . . . . . . . . 120
 DISPLAY UNITS IN . . . . . . . . . . . . . . . . . . . . 120
 SYSTEM STATUS . . . . . . . . . . . . . . . . . . . . . . 121
 PERSONAL SETTINGS (CUSTOMER- PROGRAMMABLE FEATURES) . . . . . . . . . . . 121
 SOUND SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . 122
 SETTING THE ANALOG CLOCK . . . . . . . . . . . . 122
103

INSTRUMENT PANEL FEATURES1 — Air Outlet6 — Radio11 — Storage Compartment
2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Climate Control
3 — Instrument Cluster 8 — Glove Compartment13 — Trunk Release Button
4 — Ignition Switch 9 — Heated Seat Switch14 — Power Outlet
5 — Analog Clock 10 — Hazard Switch
105

the headlights will turn on approxi-
mately 10 seconds after the wipers are
turned on. The headlights will also
turn off when the wipers are turned
off if they were turned on by this
feature. To make your selection, press
the SELECT button until ON or OFF
appears.
NOTE:
Turning the headlights on during
the daytime causes the instrument
panel lights to dim. To increase the
brightness, refer to “Lights” in
“Understanding The Features Of
Your Vehicle.”
Key Off Power Delay
When this feature is selected, the
power window switches, radio,
Uconnect™ phone, and power outlets
will remain active for up to 10 min-
utes after the ignition switch is turned
to the LOCK position. Opening either
front vehicle door will cancel this fea-
ture. To make your selection, press the
SELECT button until OFF, 45 sec, 5
min, or 10 min appears.Illumin. Approach
When this feature is selected, the
headlights will activate and remain on
for up to 90 seconds when the doors
are unlocked with the remote keyless
entry transmitter. To make your selec-
tion, press the SELECT button until
“OFF,” “30 sec,” “60 sec,” or
“90 sec” appears.
Display Units In
The EVIC and odometer can be
changed between English and Metric
units of measure. To make your selec-
tion, press and release the SELECT
button until “U.S.” or “METRIC” ap-
pears.
Compass Variance
Refer to “Compass Display” for more
information.
Calibrate Compass
Refer to “Compass Display” for more
information.
SOUND SYSTEMS
Refer to your Sound Systems Booklet.
SETTING THE ANALOG
CLOCK
To set the analog clock, located at the
top center of the instrument panel,
press and hold the button in until the
setting is correct. The clock will adjust
slowly at first and then quicker the
longer the button is held.
Setting The Analog Clock
122

STEERING WHEEL
AUDIO CONTROLS
The remote sound system controls are
located on the rear surface of the
steering wheel, at the three and nine
o'clock positions.
Theright-hand rocker switch has a
pushbutton in the center, and controls
the volume and mode of the sound
system. Pressing the top of the rocker
switch will increase the volume.
Pressing the bottom of the rocker
switch will decrease the volume.
Pressing the center button changes
the operation of the radio from MW to
LW, or to CD mode, depending on
which radio is in the vehicle. The left-hand rocker switch has a
pushbutton in the center. The func-
tion of the left-hand switch is differ-
ent, depending on which mode you
are in.
The following describes the left-hand
rocker switch operation in each mode.
RADIO OPERATION
Pressing the top of the switch will
SEEK up for the next listenable sta-
tion, and pressing the bottom of the
switch will SEEK down for the next
listenable station.
The button located in the center of the
left-hand switch will tune to the next
preset station that you have pro-
grammed in the radio preset pushbut-
ton.
CD PLAYER
Pressing the top of the switch once
will go to the next track on the CD.
Pressing the bottom of the switch once
will go to the beginning of the current
track, or to the beginning of the pre-
vious track if it is within one second
after the current track begins to play.
If you press the switch up or down
twice it plays the second track; three
times, it will play the third, etc.
The button in the center of the left-
hand switch has no function in this
mode.
RADIO OPERATION AND
MOBILE PHONES
Under certain conditions, the mobile
phone being on in your vehicle can
cause erratic or noisy performance
from your radio. This condition may
be lessened or eliminated by relocat-
ing the mobile phone antenna. This
condition is not harmful to the radio.
If your radio performance does not
satisfactorily “clear” by the reposi-
tioning of the antenna, it is recom-
mended that the radio volume be
turned down or off during mobile
phone operation.
CLIMATE CONTROLS
The air conditioning and heating sys-
tem is designed to make you comfort-
able in all types of weather.Remote Sound System Controls (Back
View Of Steering Wheel)
123

CavityCartridge Fuse Mini Fuse Description
14 —10 Amp Red Instrument Panel
15 40 Amp Green —Radiator Fan Relay
16 —15 Amp Lt. Blue Sunroof (for versions/markets, where pro-
vided)
17 —10 Amp RedWireless Control Module (WCM)/Clock/
Steering Control Module (SCM)
18 40 Amp Green —Auto Shutdown (ASD) Relay
19 —20 Amp Yellow Audio Amplifier (for versions/markets,
where provided)
20 —15 Amp Lt. Blue Radio
21 —10 Amp Red Siren (for versions/markets, where provided)
22 —10 Amp RedIgnition Run – Climate Controls/Hot Cup-
holder (for versions/markets, where pro-
vided)
23 —15 Amp Lt. Blue Auto Shutdown (ASD) Relay 3
24 —25 Amp Natural Sunroof (for versions/markets, where pro-
vided)
25 —10 Amp RedIgnition Run — Heated Mirrors (for
versions/markets, where provided)
26 —15 Amp Lt. Blue Auto Shutdown (ASD) Relay 2
27 —10 Amp RedIgnition Run – Occupant Classification Mod-
ule (OCM)/Occupant Restraint Controller
(ORC)
28 —10 Amp RedIgnition Run — Occupant Classification
Module (OCM)/Occupant Restraint Control-
ler (ORC)
29 — —Hot Car (No Fuse Required)
30 —20 Amp Yellow Ignition Run – Heated Seats (for versions/
markets, where provided)
201

2. Reach into engine compartment
and from behind the lamp assembly
and grasp the connector.
3. Rotate bulb and connector one-
quarter turn and pull outward from
assembly.CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life.
4. Pull the bulb out of the socket and
replace the bulb. 5. If the bulb comes in contact with
any oily surface, clean the bulb with
rubbing alcohol.
6. Reinsert the bulb and socket as-
sembly and rotate clockwise one-
quarter turn to secure.
FRONT TURN SIGNAL
1. Raise and prop open the hood.
2. Rotate the
bulb's electrical con-
nector one-quarter turn counter-
clockwise and remove it from the
headlamp housing.
3. Remove the bulb from the connec-
tor socket and install the replacement
bulb.
4. Install the bulb and connector as-
sembly into the headlamp housing
and rotate the connector one-quarter
turn clockwise to lock it in place. FRONT FOG LAMP
NOTE:
Access to the lamps through the
lower fascia cutout is limited. We
recommend you access the lamps
by turning the steering wheel to
allow access and remove the inner
fender shield.
1. Rotate the
bulb's electrical con-
nector one-quarter turn counter-
clockwise and remove it from the fog
lamp housing.
2. Remove the bulb from the connec-
tor socket and install the replacement
bulb.
CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life. If the bulb
comes in contact with an oily sur-
face, clean the bulb with rubbing
alcohol.
3. Install the bulb and connector as-
sembly into the fog lamp housing and
rotate the connector one-quarter turn
clockwise to lock it in place.
204

REAR TURN SIGNAL
LAMPS
1. Open the trunk and gently pull
back the trunk liner behind the tail
lamp (requires removal of a push pin
holding the trunk trim in place near
the tail lamp).
2. Remove the two plastic wing nuts
from the tail lamp housing.
NOTE:
Placing a small flat head screw-
driver or similar tool between the
lamp outboard ball stud and plas-
tic grommet from inside the trunk
can help to disengage the outboard
edge of the tail lamp.
3. Grasp the tail lamp by both the
outboard and inboard sides, and pull
firmly to disengage the tail lamp from
the vehicle.NOTE:
It is normal to hear a loud sound
when the lower tail lamp area un-
snaps from the vehicle mounting
bracket during tail lamp removal.
4. Twist and remove socket from
lamp.
5. Remove bulb from socket and re-
place.
6. Reinstall the tail lamp, fasteners,
and trunk liner.
BACKUP LAMP
1. Remove four push pins from the
bottom of the lower valance (from left
to right: 1st, 3rd, 6th & 8th) and two
push pins from the rear of the bracket.
2. Remove bracket by pulling for-
ward of vehicle.
3. Remove socket from housing with
a counter-clockwise
14turn.
4. Remove bulb from socket by pull-
ing directly out (do not turn/twist)
and install replacement bulb.
5. Insert socket back into the housing
with a clockwise
14turn.
6. Return bracket into position.
7. Snap the six (6) push pins back
into place.
LICENSE PLATE LAMP
1. Using a small screwdriver, press
inward the locking tab on the side of
the lamp assembly and pull down on
the lamp assembly for removal.
2. Remove bulb socket by twisting
out of lamp assembly.
3. Pull bulb from socket, replace, and
reinstall the bulb socket into lamp
assembly.
4. Install lamp assembly to lightbar
ensuring the locking tab is secure.
205