2012 Lancia Flavia hood open

 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 66
 PHONE CALL FEATURES . . . . . . . . . . . . . . . . 70
 UCONNECT™ PHONE FEATURES . . . . . . . . . . 72
 ADVANCED PHONE CONNECTIVITY . . . . . . . 75
 THINGS YOU SHOULD KNOW ABOUTYOUR UCONNECT™ PHONE . . . . . . . . . . . . . . 76
 VOICE COMMAND . . . . . . . . . . . . . . . . . . . . . . . . 82  VOICE COMMAND SYSTEM OPERATION . . . . 82
 COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . 83
 VOICE TRAINING . . . . . . . . . . . . . . . . . . . . . . 85
 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85  POWER SEATS . . . . . . . . . . . . . . . . . . . . . . . . 85
 HEATED SEATS . . . . . . . . . . . . . . . . . . . . . . . . 86
 RECLINER ADJUSTMENT . . . . . . . . . . . . . . . . 87
 LUMBAR SUPPORT . . . . . . . . . . . . . . . . . . . . . 87
 EASY ENTRY SYSTEM . . . . . . . . . . . . . . . . . . 88
 HEAD RESTRAINTS . . . . . . . . . . . . . . . . . . . . 88
 TO OPEN AND CLOSE THE HOOD . . . . . . . . . . . 90
 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91  MULTIFUNCTION LEVER . . . . . . . . . . . . . . . . 91
 HEADLIGHTS AND PARKING LIGHTS . . . . . . 91
 LIGHTS-ON REMINDER . . . . . . . . . . . . . . . . . 91
 AUTOMATIC HEADLIGHTS . . . . . . . . . . . . . . . 91
 HEADLIGHTS WITH WIPERS (AVAILABLEWITH AUTOMATIC HEADLIGHTS ONLY) . . . . 91
 HEADLIGHT TIME DELAY . . . . . . . . . . . . . . . 92
50

TO OPEN AND CLOSE
THE HOOD
Two latches must be released to open
the hood.
1. Pull the hood release lever located
under the left side of the instrument
panel.
2. Move to the outside of the vehicle
and locate the hood safety catch at the
center front edge of the hood.3. Lift the secondary latch under-
neath the center front edge of the
hood and raise the hood.
4. Use the hood prop rod to secure the
hood in the open position. Place the
upper end of the prop rod in the hole
on the underside of the hood.
Before closing the hood, make sure to
stow the prop rod in its proper loca-
tion.
CAUTION!
To prevent possible damage, do not
slam the hood to close it. Use a firm
downward push at the center of the
hood to ensure that both latches en-
gage.WARNING!
Be sure the hood is fully latched
before driving your vehicle. If the
hood is not fully latched, it could
open when the vehicle is in motion
and block your vision. Failure to
follow this warning could result in
serious injury or death.
Hood Release Lever
Hood Safety Catch location
Secondary Latch
Hood Prop Rod Hole Location
90

DOWN ButtonPress and release the
DOWN button to advance
the display through the
various Trip Functions or
Personal Settings.
COMPASS Button
Press and release the COM-
PASS button to display the
compass heading, the outside
temperature, and Audio Info
(when the radio is on) screen
when the current screen is not the com-
pass, outside temp, audio info screen.
SELECT Button
Press and release the SE-
LECT Button to accept a
selection. The SELECT
Button also resets various
Trip Functions.
ELECTRONIC VEHICLE
INFORMATION CENTER
(EVIC) DISPLAYS
When the appropriate conditions ex-
ist, the EVIC displays the following
messages:
Turn Signal On (with a continuous
warning chime after one mile traveled)
 Left Front Turn Signal Lamp Out (with a single chime)
 Left Rear Turn Signal Lamp Out (with a single chime)
 Right Front Turn Signal Lamp Out (with a single chime)
 Right Rear Turn Signal Lamp Out (with a single chime)
 RKE (Remote Keyless Entry) Bat- tery Low (with a single chime)
 Personal Settings Not Avail – Ve- hicle Not in Park
 Personal Settings Not Avail – Ve- hicle in Motion
 Door Ajar (with vehicle graphic showing which door is open. A
single chime sounds if the vehicle is
in motion).
 Doors Ajar (with vehicle graphic showing which doors are open. A
single chime sounds if the vehicle is
in motion).
 Trunk Open (with vehicle graphic showing and open trunk and A
single chime )
 Lights On  Key In Ignition
 Remote start aborted — Door ajar
 Remote start aborted — Hood ajar
 Remote start aborted — Trunk ajar
 Remote start aborted — Fuel low
 Remote start disabled — System
fault
 Convertible Top Not Secured (with a single chime)
 Convertible Top Complete (with a single chime)
 Secure Cargo Shield (with a single chime)
 Speed Too High (with a single chime)
 Convertible Top Malfunction (with a single chime)
 Oil Change Required (with a single chime)
 Low Tire (with a graphic of the car showing which tire(s) is/are low -
with a single chime). Refer to "Tire
Pressure Monitoring System" in
"Starting and Operating".
116

HAZARD WARNING
FLASHERS
The Hazard Warning flasher switch is
located on the instrument panel, be-
low the radio.Press the switch to turn on the
Hazard Warning flasher. When
the switch is activated, all di-
rectional turn signals will flash on and
off to warn oncoming traffic of an
emergency. Press the switch a second
time to turn off the Hazard Warning
flashers.
This is an emergency warning system
and it should not be used when the
vehicle is in motion. Use it when your
vehicle is disabled and it is creating a
safety hazard for other motorists.
When you must leave the vehicle to
seek assistance, the Hazard Warning
flashers will continue to operate even
though the ignition is placed in the
OFF position.
NOTE:
With extended use the Hazard
Warning flashers may wear down
your battery. IF YOUR ENGINE
OVERHEATS
In any of the following situations, you
can reduce the potential for overheat-
ing by taking the appropriate action.
 On the highways — Slow down.
 In city traffic — While stopped, put
transaxle in NEUTRAL, but do not
increase engine idle speed.
CAUTION!
Driving with a hot cooling system
could damage your vehicle. If tem-
perature gauge reads “H”, pull over
and stop the vehicle with the engine
at idle, when safe. Turn the air con-
ditioner off and wait until the
pointer drops back into the normal
range. After appropriate action has
been taken, if the pointer remains on
the “H”, turn the engine off imme-
diately, and call for service.
NOTE:
There are steps that you can take to
slow down an impending overheat
condition:  If your air conditioner (A/C) is
on, turn it off. The A/C system
adds heat to the engine cooling
system and turning the A/C off
can help remove this heat.
 You can also turn the tempera- ture control to maximum heat,
the mode control to floor and the
blower control to high. This al-
lows the heater core to act as a
supplement to the radiator and
aids in removing heat from the
engine cooling system.
WARNING!
You or others can be badly burned
by hot engine coolant (antifreeze) or
steam from your radiator. If you see
or hear steam coming from under
the hood, do not open the hood until
the radiator has had time to cool.
Never try to open a cooling system
pressure cap when the radiator or
coolant bottle is hot.
166

PREPARATIONS FOR
JUMP-START
The battery in your vehicle is located
between the left front headlight as-
sembly and the left front wheel splash
shield. To allow jump-starting there
are remote battery posts located on
the left side of the engine compart-
ment.WARNING!
 Take care to avoid the radiatorcooling fan whenever the hood is
raised. It can start anytime the
ignition switch is on. You can be
injured by moving fan blades.
(Continued)
WARNING!(Continued)
 Remove any metal jewelry such as
watch bands or bracelets that
might make an inadvertent elec-
trical contact. You could be seri-
ously injured.
 Batteries contain sulfuric acid
that can burn your skin or eyes
and generate hydrogen gas which
is flammable and explosive. Keep
open flames or sparks away from
the battery.
1. Set the parking brake, shift the
automatic transmission into PARK
and turn the ignition to LOCK.
2. Turn off the heater, radio, and all
unnecessary electrical accessories.
3. Remove the protective cover over
the remote positive (+)battery post.
To remove the cover, press the locking
tab and pull upward on the cover. 4. If using another vehicle to jump-
start the battery, park the vehicle
within the jumper cables reach, set
the parking brake and make sure the
ignition is OFF.
WARNING!
Do not allow vehicles to touch each
other as this could establish a
ground connection and personal in-
jury could result.
JUMP-STARTING
PROCEDUREWARNING!
Failure to follow this procedure
could result in personal injury or
property damage due to battery ex-
plosion.
Remote Battery Posts
1 — Remote Positive (+) Post (cov-
ered with protective cap)
2 — Remote Negative (-) Post
Locking Tab
173

The A/C Air Filter is located in the
fresh air inlet behind the glove box.
Perform the following procedure to
replace the filter:
1. Open the glove box and remove all
contents.
2. Push in on the sides of the glove
box and lower the door.
3. Disconnect the glove box door
dampener from the slot on the side of
the box. This is done by grasping the
dampener connector (on the outside
of the box) and the end of the connec-
tor pin (on the inside of the box) with
your thumb and forefinger and pull-
ing outward while lightly lifting up-
ward on the door with your other
hand. Once disconnected, the damp-
ener will retract underneath the in-
strument panel if you release it.
4. Pivot the glove box downward.
5. Disengage the two retaining tabs
that secure the filter cover to the
HVAC housing and remove the cover.6. Remove the A/C Air Filter by pull-
ing it straight out of the housing.
7. Install the A/C Air Filter with the
arrow on the filter pointing toward
the floor. When installing the filter
cover, make sure the retaining tabs
fully engage the cover.
CAUTION!
The A/C Air Filter is identified with
an arrow to indicate airflow direc-
tion through the filter. Failure to in-
stall the filter properly will result in
the need to replace it more often.
8. Reinstall the glove box door damp-
ener and glove box. BODY LUBRICATION
Locks and all body pivot points, in-
cluding such items as seat tracks, door
hinge pivot points and rollers, and
hood hinges, should be lubricated pe-
riodically with a lithium based grease
to assure quiet, easy operation and to
protect against rust and wear. Prior to
the application of any lubricant, the
parts concerned should be wiped
clean to remove dust and grit; after
lubricating excess oil and grease
should be removed. Particular atten-
tion should also be given to hood
latching components to ensure proper
function. When performing other un-
derhood services, the hood latch, re-
lease mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be
lubricated twice a year, preferably in
the Fall and Spring. Apply a small
amount of a high quality lubricant
directly into the lock cylinder.
A/C Air Filter Replacement
187

In unusual situations involving
grossly malfunctioning engine opera-
tion, a scorching odor may suggest
severe and abnormal catalyst over-
heating. If this occurs, stop the ve-
hicle, turn off the engine and allow it
to cool. Service, including a tune-up
to manufacturer's specifications,
should be obtained immediately.
To minimize the possibility of cata-
lytic converter damage:
 Do not shut off the engine or inter- rupt the ignition, when the trans-
mission is in gear and the vehicle is
in motion.
 Do not try to start the engine by pushing or towing the vehicle.
 Do not idle the engine with any spark plug wires disconnected or
removed, such as when diagnostic
testing, or for prolonged periods
during very rough idle or malfunc-
tioning operating conditions. COOLING SYSTEM
WARNING!
 When working near the radiator
cooling fan, disconnect the fan
motor lead or turn the ignition
switch to the LOCK position. The
fan is temperature controlled and
can start at anytime the ignition
switch is in the ON position.
 You or others can be badly burned
by hot engine coolant (antifreeze)
or steam from your radiator. If
you see or hear steam coming
from under the hood, do not open
the hood until the radiator has
had time to cool. Never try to open
a cooling system pressure cap
when the radiator is hot.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we do
recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
Coolant ChecksCheck engine coolant (antifreeze) pro-
tection every 12 months (before the on-
set of freezing weather, where appli-
cable). If the engine coolant (antifreeze)
is dirty or rusty in appearance, the sys-
tem should be drained, flushed, and re-
filled with fresh engine coolant (anti-
freeze). Check the front of the A/C
condenser for any accumulation of bugs,
leaves, etc. If dirty, clean by gently
spraying water from a garden hose ver-
tically down the face of the condenser.Check the coolant recovery bottle
tubing for brittle rubber, cracking,
tears, cuts, and tightness of the con-
nection at the bottle and radiator. In-
spect the entire system for leaks.
190

Master Cylinder – Brake Fluid
Level Check
Check the fluid level in the master
cylinder immediately if the brake sys-
tem warning light indicates system
failure.
Check the fluid level in the master
cylinder when performing underhood
services.
Clean the top of the master cylinder
area before removing the cap. If nec-
essary, add fluid to bring the fluid
level up to the requirements described
on the brake fluid reservoir.
Overfilling of fluid is not recom-
mended because it may cause leaking
in the system.
Fluid level can be expected to fall as
the brake pads wear. Brake fluid level
should be checked when pads are re-
placed. However, low fluid level may
be caused by a leak and a checkup
may be needed.
Use only manufacturer's recom-
mended brake fluid. Refer to “Fluids,
Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for fur-
ther information.
WARNING!
 Use the manufacturer’s recom- mended brake fluid or a quality-
equivalent product. Refer to “Flu-
ids, Lubricants, and Genuine
Parts” in “Maintaining Your Ve-
hicle” for further information. Us-
ing the wrong type of brake fluid
can severely damage your brake
system and/or impair its perfor-
mance.
 To avoid contamination from for-
eign matter or moisture, use only
new brake fluid or fluid that has
been in a tightly closed container.
Keep the master cylinder reservoir
cap secured at all times. Brake
fluid in a open container absorbs
moisture from the air resulting in
a lower boiling point. This may
cause it to boil unexpectedly dur-
ing hard or prolonged braking,
resulting in sudden brake failure.
This could result in a collision.
(Continued)
WARNING!(Continued)
 Overfilling the brake fluid reser-
voir can result in spilling brake
fluid on hot engine parts, causing
the brake fluid to catch fire. Brake
fluid can also damage painted and
vinyl surfaces, care should be
taken to avoid its contact with
these surfaces.
 Do not allow petroleum based
fluid to contaminate the brake
fluid. Brake seal components
could be damaged, causing partial
or complete brake failure. This
could result in a collision.
AUTOMATIC
TRANSMISSION
The automatic transmission and dif-
ferential assembly are contained
within a single housing.
The fluid level in the automatic trans-
mission should be checked whenever
the vehicle is serviced. Operation with
an improper fluid level will greatly
reduce the life of the transmission and
the fluid.
194