2012 Citroen C5 reset
[x] Cancel search: resetPage 17 of 316
15
FAMILIARISATION
MONITORING
Instrument panel
The hazard warning lamps
can also be used with the
ignition switched off.
A.
Fuel gauge and low fuel warning lamp.
B.
Cruise control/speed limiter information.
C.
Coolant temperature.
D.
Speedometer.
E.
Instrument panel screen.
F.
Mileage recorder.
G.
Trip mileage recorder reset button.
H.
Rev counter.
I.
Engine oil temperature.
J.
Automatic gearbox information.
- When the ignition is switched on, the orange and
red warning lamps come on.
- When the engine is running, these warning lamps
should go off .
- If any warning lamps remain on, refer to the
"Monitoring" section.
Hazard warning lamps
26
114
Page 28 of 316
I
26
MONITORING
INSTRUMENT PANELS - PETROL AND DIESEL - MANUAL AND AUTOMATIC GEARBOX
Panel grouping together the dials and vehicle operation indicator and warning lamps.
A.
Fuel gauge
B.
Indicator:
●
Coolant temperature
●
Cruise control/Speed limiter
information
C.
Speedometer
D.
Rev counter
E.
Indicator:
●
Engine oil temperature
●
Gear lever position and gear
engaged (Automatic gearbox)
F.
Controls:
●
Lighting dimmer
●
Resetting to zero of trip mile-
age computer and mainte-
nance indicator
G.
Instrument panel screen indicating:
●
Depending on the page
selected with the left-hand
thumb wheel on the steering
wheel:
- Digital speed repeater
- Trip computer
- Navigation (guidance) infor-
mation
- Display of message alerts
- Engine oil level check
- Service indicator
●
Permanently:
- Trip mileage recorder
- Total mileage recorder
Page 31 of 316
I
29
MONITORING
TRIP COMPUTER
System which provides current in-
formation concerning your journey
(range, consumption, etc.)
Information displays
Trip zero reset
The trip computer is displayed in the
instrument panel screen.
)
Turn the left-hand thumb wheel A
on the steering wheel to display
the various trip computer tabs in
succession:
- the current information tab is
displayed in zone B
of the in-
strument panel screen, with:
●
the range,
●
the current fuel consumption,
●
the digital speed reading or
the Stop & Start time counter.
- the trip "1"
tab is displayed in
zone C
of the instrument panel
screen, with:
●
the distance travelled,
●
the average fuel consumption,
●
the average speed,
for the fi rst trip.
- the trip "2"
tab is displayed in
zone C
of the instrument panel
screen, with:
●
the distance travelled,
●
the average fuel consumption,
●
the average speed,
for the second trip.
)
When the trip required is dis-
played, press the left-hand thumb
wheel on the steering wheel for
more than two seconds.
Trips "1"
and "2"
are independent
but their use is identical.
For example, trip "1"
can be used for
daily fi gures and trip "2"
for monthly
fi gures.
Page 32 of 316
I
30
MONITORING
A few definitions
(trip computer)
Range
(miles or km)
Current fuel
consumption
(mpg or l/100 km or km/l)
Average fuel
consumption
(mpg or l/100 km or km/l)
Average speed
(mph or km/h)
Distance travelled
(miles or km)
This indicates the distance which
can still be travelled with the fuel re-
maining in the tank in relation to the
average fuel consumption over the
last few miles (kilometres) travelled.
This value may vary following a
change in the style of driving or
the relief, resulting in a signifi cant
change in the current fuel con-
sumption.
When the range falls below 20 miles
(30 km), dashes are displayed. After
fi lling with at least 5 litres of fuel,
the range is recalculated and is dis-
played when it exceeds 60 miles
(100 km).
If dashes are displayed continu-
ously while driving in place of the
digits, contact a CITROËN dealer
or a qualifi ed workshop. This function is only displayed from
20 mph (30 km/h). This is the average fuel consump-
tion during the last few seconds.
This is the average fuel consump-
tion since the last trip computer zero
reset.
This is the average speed calculated
since the last trip computer zero reset
(ignition on). This indicates the distance travelled
since the last trip computer zero reset.
Stop & Start time
counter
(minutes / seconds or hours /
minutes)
If your vehicle is fi tted with Stop &
Start, a time counter calculates the
time spent in STOP mode during a
journey.
It resets to zero every time the igni-
tion is switched on with the key.
Page 41 of 316
I
39
MONITORING
Service indicator
This information is displayed for a
few seconds when the ignition is
switched on. It informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last
service.
More than 2 000 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no
service information appears on the
instrument panel central screen.
Between 600 miles (1 000 km)
and 2 000 miles (3 000 km) remain
before the next service is due
For 7 seconds after the ignition is switched
on, the spanner symbolising the service
operations comes on. The instrument pan-
el central screen indicates the distance re-
maining before the next service is due.
Example:
1 900 miles remain before the
next service is due.
For 7 seconds after the ignition is switched
on, the central screen indicates:
Less than 600 miles (1 000 km)
remain before the next service is due
Example:
500 miles remain before
the next service is due.
For 7 seconds after the ignition is
switched on, the central screen in-
dicates:
Service overdue
For 7 seconds after the ignition is
switched on, the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.
Example:
the service is overdue by
180 miles.
For 7 seconds after the ignition is switched
on, the central screen indicates:
The spanner remains on
in the
screen to indicate that a service
must be carried out soon.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
The spanner remains on
in the
screen to indicate that a service
should have been carried out.
Page 42 of 316
I
40
MONITORING
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
)
switch off the ignition,
)
press and hold the trip distance
recorder zero reset button,
)
switch on the ignition; the dis-
tance recorder display begins a
countdown,
)
when the display indicates "=0"
,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.
Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 30 minutes.
Oil level correct
Oil level incorrect
This is indicated by the message
"Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine.
Oil level gauge problem
This is indicated by the message "Oil
level measurement invalid". Contact
a CITROËN dealer or a qualifi ed
workshop.
Page 44 of 316
I
42
MONITORING
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
To conform to legislation in the
country you are crossing, change
the units of distance (miles or km)
via the confi guration menu.
Lighting dimmer
System for manual adjustment of
the brightness of the instruments
and controls in relation to the exte-
rior brightness.
Operation
)
Press button A
to decrease the
brightness of the instruments
and controls.
)
Press button B
to increase the
brightness of the instruments
and controls.
Deactivation
When the lighting is off, or in day
mode on vehicles fi tted with daytime
running lamps, pressing the buttons
does not have any effect.
Trip distance recorder
System which measures a distance
travelled during a day or other pe-
riod since it was reset to zero by the
driver.
)
With the ignition on, press the
button until zeros appear.
Page 150 of 316
IX
148
DRIVING
FIXED CENTRED CONTROLS STEERING WHEEL
1
Rotation
-
Scroll the various pages of information on the instrument panel
screen.
- Move through the various menus on the instrument panel screen.
- Increase/decrease values.
Short press
- Open the menu on the instrument panel screen (only when stationary).
- Select and confi rm information.
Long press Trip computer zero reset (if the trip computer page is
displayed).
2
Short press
- Cancel the current operation.
-
Return to the previous screen on the instrument panel screen.
Long press Return to the initial page on the instrument panel screen.
3
Short press
Increase the speed in steps of 1 mph (1 km/h) / storing the speed.
Maintained press Increase the speed in steps of 5 mph (5 km/h).
4
Short press
Decrease the speed in steps of 1 mph (1 km/h) / storing the speed.
Maintained press Decrease the speed in steps of 5 mph (5 km/h).
5
Short press Suspend or resume cruise control/speed limiter (depending
on the mode selected).
6
Short press Select cruise control or speed limiter mode (the cycle on this
button will always begin with selection of the speed limiter).
7
Short press Deactivate cruise control/speed limiter.
8
Short press
- Pick up an incoming call.
- Hang up the current call.
- Open the telephone short-cut menu.
- Confi rm on the list and the telephone menu.
Long press Refuse an incoming call.
9
Short press / Long press Horn.
10
Short press Activate/deactivate Black Panel mode (night driving).
11
Short press Activate the voice command.
Long press Navigation instruction repeat.