2012 AUDI R8 SPYDER warning

dealer will g ladly provide you with more
information.
Uniform tire quality grading
- Tread wear
- Traction AA A B C
- T emperature ABC
Quality grades can be found where applicable
on the ti re side wa ll between tread shoulde r
and maximum section wid th ¢ page 193,
fig. 151 .
For example : Tread wear 200, Tract ion AA ,
Temperatu re A .
All passenger car tires must conform to Feder­
al Safety Requi rements in addition to these
grad es.
Tread we ar
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a spec ified
government test course .
For example, a t ire graded 150 would wear
one and one half (1 1/2) t imes as well on the
government course as a tire graded 100 .
The relat ive perform a nee of ti res depends
upon the actua l conditions of their use, how­
ever, and may depart sign ificantly from the
norm due to var iat ions in dr iv ing habits, serv­
i ce practices and differences in road character­
i stics and climate.
Traction
The traction grades, from highest to lowest,
are AA, A, B and
C. Those grades represent the
tire's abil ity to stop on wet pavement as
measured unde r controlled cond it ions on
spec ified gove rnment test su rfaces of asphalt
and concrete . A tire ma rked C may h ave po or
t ra ction perfo rm ance¢ &..
Temp erature
The temperature grades are A (the h ighest),
B, and C, repr ese nting the t ire's resistance to
the gene rat io n of heat and its ab ility to dissi-
Tire s an d wheel s 197
pate heat when tested under controlled condi ­
tions on a specified indoor laboratory test
whee l.
Sustaine d high temperature can cause the
mater ia l of the tire to degenerate and red uce
tire life, and excessive tempe rat ure ca n lead
to s udden tire failure ¢ &. .
T he gr ade C correspon ds to a level of pe rform ­
ance which all passenger car tires must meet u nder the Federal Motor Vehicle Safety Stand­
ard No . 109 . Grades Band A represent higher
l evels of performance on the laboratory test
whee l than the minimum requ ired by law.
A WARNING
The traction grade assigned to th is tire is
based on straight-ahead braking traction
tests, and does not include accele rat ion,
cor neri ng, hy droplaning or peak t ra ction
ch aracte rist ics.
A WARNING
T he temperature grade for this tire is es­
tablishe d for a tire that is properly inf lated
and not overloaded . Excess ive speed, un­
derinflation, or excessive loading, e it h er
separately or in combinat ion, can ca use
heat bui ldup and possible tire failure.
Winter tires
Winter tires can improve vehicle handling on
snow and ice. At temperatures below 45 °F (7 °C) we recommend changing to winter
tires.
In some heavy snow areas, local governments
may require true w inter or "snow" tires, those
with very deeply cut tread. T hese tires should
o nl y be used in pairs and be installed o n all
fou r wheels . Make sure you purchase snow
ti res that a re the same si ze and construction
type as the othe r ti res on you r vehicle.
If your vehicle is equipped w ith all-whee l
drive*, th is w ill improve traction during winter
driv ing, even with the s tanda rd tires . Howev-
er, we stro ngly recommend that you always ..,.
•
•

198 Tire s and wheel s
equip a ll four wheels on your vehicle with cor ­
rectly fitted winter tires or all-season tires,
when winter road conditions are expected .
This a lso improves the vehicle's braking per­
formance and reduces stopping distances.
Summer tires provide less grip on ice and
snow.
W inter t ires (snow t ires) must always be fitted
on all four whee ls .
Compat ible tire pressure mo nitor ing sensors
must be installed on all fo ur winter tires for
the tire pressure monitoring system to func­
tion proper ly
i=;, poge 195 .
Ask your autho rized Aud i dea ler o r qualified
wo rkshop fo r permitted
winter tir e size s . Use
on ly radia l w inte r tires .
W inter t ires lose the ir effectiveness when the
tread is worn down to a depth of 0.157 inch
(4 mm) .
Only drive with wi nter tires under winter con­
d itions . Summer tires hand le better when
there is no snow or ice on the roads and the
temperature is above 45 °F (7 °C).
Please always remembe r that w inte r tires may
have a lower speed rating than the t ires origi­
na lly installed on your veh icle at the t ime i t
was manufactured. Please see
r=;, page 194 ,
Speed roting (letter code) for a list ing of the
speed rating letter codes and the maximum
speed at which the tires can be driven.
The speed ra ting lette r code
(i=;, poge 185) is
on the s ide wall of the tire
i=;, poge 193.
A WARNING
Winter tires have maximum speed limits
that may be lower than your vehicle's max ­
im um speed . Always know the maxim um
speed before driving off. Never drive faster
than the speed permitted for your specific
w inte r tires . This will cause damage to the
tires leading to an accident and serious
personal in ju ry to you and yo ur passen­
gers.
A WARNING
Driving faster than the maximum speed
for which the winter tires on your veh icle
were designed can cause t ire failure in­
cluding a blowout and sudden deflation,
l oss of cont ro l, crashes and ser ious per­
sonal injuries. Have wo rn o r damaged ti res
r eplaced immedia tely.
- W inte r ti res have maxim um speed rating
tha t may be lower than your vehicle 's
maximum speed.
- Never drive fas ter than the speed for
which the win ter or othe r ti res installed
on yo ur vehicle are rated.
A WARNING ~
A lways ad just your driving to the road and
traffic condit ions. Never let the good ac­
celeration o f the winter tires and a ll-wheel
drive tempt yo u into taking extra risks. Al­
ways remember:
- When braking, an all-wheel drive veh icle
handles in the same way as a front drive
veh icle.
- Drive carefully and reduce your speed on
icy and slippery roads, even w inter t ires
cannot help under black ice conditions .
~ For the sake of the environment
Use summer tires when weather condi ­
tions permit. They are qu ieter, do not wear
as quickly and reduce fuel consumpt ion.
Snow chains
-
Snow cha ins may be fitted only to the rea r
whee ls, and o nly to certa in tire sizes . Ask your
autho rized Aud i dea le r o n whi ch t ire si zes
snow c hains ca n be used.
T he snow chains must have low-p rofile links
and must not be t hicker than 0 .53 inch
(13 .5 mm), in cl ud ing the lo ck.
Remove wheel center covers before putt ing
snow c ha ins on your vehicle
r=;, @ . For safety
reasons cover caps must then be f itted over

the wheel bolts. These are available from au­
thorized Audi dealers.
A WARNING
Using the wrong snow chains for your vehi­
cle or installing them incorrectly can in­
crease the risk of loss of control leading to
serious personal injury.
- Snow chains are available in different
sizes. Always make sure to follow the in­
structions provided by the snow chain
manufacturer .
- When driving with snow chains, never
drive faster than the speed permitted for
your specific snow chains.
- Always observe local regulations.
- Remove snow chains before driving on
roads not covered with snow to avoid
damaging tires and wearing the snow
chains down unnecessarily.
- Snow chains, which come into direct con­
tact with the wheel rim, can scratch or
damage it. Therefore, make sure that the
snow chains are suitably covered . Check
the position of the snow chains after
driving a few yards and correct if neces­
sary. Follow the instructions from the
snow chain manufacturer when doing so.
(D Tips
Where snow chains are mandatory oncer­
tain roads, this normally also applies to ve­
hicles with all-wheel drive.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque.
The design of wheel bolts is matched to the
factory installed rims. If different rims are fit­
ted, the correct wheel bolts with the right
length and correctly shaped bolt heads must
be used. This ensures that wheels are fitted
securely and that the brake system functions
correctly .
Tires and wheels 199
In certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same model
r:!> page 221.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose causing loss of
control, a collision and serious personal in­
jury.
- Always keep the wheel bolts and the
threads in the wheel hubs clean so the
wheel bolts can turn easily and be prop­ erly tightened.
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose while driving if greased or
oiled, even if tightened to the specified
torque.
- Only use wheel bolts that belong to the
rim being installed.
- Never use different wheels bolts on your
vehicle.
-Always maintain the correct tightening
torque for the wheel bolts to reduce the
risk of a wheel loss. If the tightening tor­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cle is moving.
If the tightening torque is
too high, the wheel bolts and threads
can be damaged and the wheel can be­
come loose.
(D Note
The specified torque for the wheel bolts is
90 ft lb (120 Nm) with a tolerance of ± 7 .4
ft lb( ± 10 Nm). Torque wheel bolts diago­
nally. After changing a wheel, the torque
must be checked as soon as possible with a
torque wrench -preferably by an author­
ized Audi dealer or qualified workshop.
Low aspect ratio tires
Your Audi is factory-equipped with low aspect
ratio tires. These tires have been thoroughly
tested and been selected specifically for your model for their superb performance, road feel
and handling under a variety of driving
IJ,,
•
•

soon as possible, and inflate them to the
proper pressure . Driving on a significant ly un­
der-inflated tire causes the tire to overheat
and can lead to tire failure. Under-inflation a l­
so reduces fuel efficiency and tire tread l ife,
and may affect the veh icle 's handling and
stopping ab ility.
Please note that the TPMS is not a substitute
for proper t ire maintenance, and it is the dr iv­
er's responsib ility to ma inta in correct t ire
p ress ure , even if under- inflation has not
reached the leve l to t rigger illumination of the
TPMS low tire pressure telltale .
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indicate when
the system is not ope rating properly. The
TPMS malfunc tion indica to r i s combined wi th
the low t ire pr essu re tellta le. When the sys ­
tem detec ts a ma lf u nct ion, the te lltale will
flash for approximately one minute and then remain continuo usly ill uminated . This se­
q uence will continue upon subsequent vehicle
start-ups as long as the malfunction ex ists.
When the malfunction indicator is ill uminat ­
ed, the system may not be able to detect or
signa l low t ire pressure as intended . TPMS
malfunct ions may occ ur for a variety of rea­
sons, including the ins talla tio n of replace­
ment or a lternate tires o r whee ls on the veh i­
cle that prevent the TPMS from funct io ni ng
p roperly . Always check the TPMS malfunct ion
t ellta le afte r replacing one o r more t ires or
wheels o n your veh icle to ensure tha t the re­
p lacemen t or a lternate tires and wheels allow
the TPMS to continue to function properly .
Introduction
The tire pressure monitoring system monitors
air pressure in all four road wheels while the
vehicle is moving .
As soon as the tire pressu re mo nitor ing sys­
tem senses a s ignificant loss of a ir pressure in
one or severa l ti res, text messages and yellow
symbo ls appear in the instr ument cluster dis ­
p lay to alert the driver. The
[ti warning light
Tire s an d wheel s 201
in the instrument cluster comes on when the
ti re is significant ly underinflated .
T he wa rni ng lig ht
[ti also illu minates i n the
case of a system mal funct io n.
Be aware that t ire pressure is a lso dependent
o n the tempe ratu re of the t ire. For eve ry 18 ° F
(10 °C) incre ase in tir e te mper ature, tire pres­
s u re inc reases by about 1.5 psi (0 .1 bar). The
ti re warms up while the ve hicle is moving and
tire p ress ure rises . So you sho uld ad just tire
pressure only when they a re
cold, when the
temperature of the tires is ro ughly the same
as the ambient a ir temperature.
In order to keep the tire press ure monito ring
system p roperly ca librated, t ire press ure on
all four tires sho uld be checked at regu lar in­
terva ls.
The tire pressure is shown on the label located
on the dr iver's side B-pillar (v is ib le when the
door is open) .
A WARNING
When the tire pressure mo nitoring system
war ning light is lit , one o r m ore of your
tires is s ignificantly under-infla ted . You
shou ld stop and check your tires as soon as
pos sib le, and in flate t hem to the proper
p ress ure a s in dic ate d on the ve hicle's ti re
p ress ure lab el
¢page 187. Driving on a
significantly under -inflated ti re causes t he
tire to over heat and can lead to tire failure .
Under-inflat ion also is like ly to impair the
vehicle's handling and stopping ab ility.
@ For the sake of the environment
D riving wit h un der -inflated tires red uces
fuel efficiency an d tire t read life.
(D Tips
- E ach tire should be chec ked monthly
w hen the tem perature of the tires is
about the same as amb ient a ir tempera­
t u re and set to the recommended infla­
tion press ure as specified on the tire
pressure label¢
page 187.
•
•

What do I do now? Trunk escape handle
Appl ies to vehicles: with trunk escape handle
In case of an emergency, the front lid can be
opened from the inside using the trunk es­
cape handle.
.. To open the front lid pull the handle.
The trunk escape handle inside the luggage
compartment is made of fluorescent materia l
to g low in the dark.
.&_ WARNING
The trunk escape handle is to be used only
in an emergency.
Breakdown kit
The breakdown kit consists of vehicle tool kit
and tire mobility system.
Fig. 152 Breakdown kit in luggage compartment
@ Vehicle tool kit
@ Tire mobility system c::> page 203
The breakdown kit is located in the luggage
compartment under the cargo floor .
The tool kit consists of the following items :
- Hook for removing hub cap
- Lug wrench
- Alignment pin for changing wheels
- Screwdriver w ith reversible blade
- Towing eye
- Jack* (not a vehicle component; contact your
authorized Audi dealer if needed)
Before returning the jack* to its place, retract
the jack arm fully .
What do I do now ? 203
Note: some of the items listed above are pro­
vided on certain mode ls only or are optional
extras.
.&_ WARNING
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts .
- The jack* (available as a replacement
part) is intended only for your vehicle
model. Under no circumstances use it to
lift heavy vehicles o r other loads; you risk
injuring yourse lf.
- Never start or run the eng ine while the
veh icle is supported by the jack *.
- If you must work under the veh icle, al­
ways use safety stands specifically de­ signed fo r th is purpose.
- Using a bumper jack to ra ise the vehicle
wi ll damage the bumpe r system. The
jack may slip, caus ing injury.
Tire repair
General and safety pointers
Tire repair is intended only for temporary,
short-term use .
Fig. 153 Ti re damage for which the Tire Mob ility Sys ­
tem is not suited
-
Your vehicle is equipped wi th a tire repa ir k it,
the
Tire M obility Sy stem (T M S).
In the event of a t ire failure, the TM S is in the
luggage compartment under the floor.
It con ­
s ists of the tire sealan t and an elec tric air
pump.

204 What do I do now?
Using TM S, tire damage caused by foreign
bodies up to about
0.16 inch (4 mm ) in diam­
eter can be sealed reliably.
The foreign object must s tay in the t ire.
The tir e sea lant mu st not be us ed :
- for cuts or punctures in the tire which are
larger than 0.16 inch (4 mm)¢ fig. 153
(D
- for damage to the rim@
- if you have been driving with very low tire
pressures or tires with no air @
Using the
TM S is described in the section
¢ page 204, Preliminary steps.
TMS can be used at temperatures down to
-4 °F (- 20 °C).
A WARNING
Take the following preca utions after re­
pairing the tire:
-
- Do not drive faster than 50 mph (80 km/
h)!
- Avoid full-throttle acce leration, heavy
braking an d fast cornering.
- The vehicle's road behavior can be affect­
ed.
- Tires sealed w ith
TMS are intended only
for
temporar y, short-term use . Dam­
aged tires must be replaced . Drive care­
fully to the next professional repair fa­
cility.
- After using the t ire sea lant the tire pres­
sure monitoring system may no longer
work properly. Drive carefully to the next professional repair fac ility.
- TMS must NOT be used,
- for cuts or pu nctures in the ti re whi ch
are larger than 0.16 inch (4 mm)
- for damage to the r im
- if you have been dr iv ing with very low
tire pressures or t ires with no air
- Seek profess ional assistance if it is not
poss ible to repair the tire with the tire
sealant.
- The tire sealant must not come into con­
tact with sk in, eyes or clothing. -
If you get any ti re sea lant in yo ur eyes or
come into contact w ith it, rinse the af­
fected area thoroughly with clean water. Find a phys ician immediately!
- Change any clothing contaminated with
tire sealant immediately.
- Do not inha le the vapor!
- If you have swallowed tire sealant, rinse
your mouth thoroughly right away and
drink plenty of water.
- Do not induce vomit ing! Find a physi­
c ian immediately!
- I f you have allergic react ions, find a
phys ic ian immediately.
- Keep the tire sealant away from children.
(D Note
Do not use commercially avai lab le tire
sealants. The e lectr ica l components of the
tire pressure monitoring system will no longe r work properly.
@) For the sake of the environment
Used sealant bottles ca n be dropped off at
a recycling facility.
(D Tips
- If sea lant has run out, allow it to dry.
Then you can peel it off.
- Have the t ire sea lant rep laced every 4
years at a dealership.
Preliminary steps
Some preliminary steps are necessary for tire
repair.
... If you have a flat tire, park the vehicle as far
as possible from moving traffic .
... App ly the
parking brake firmly.
... Engage a gear.
... Check whether a repair using the Tire Mobi­
lity System is poss ible ¢ page 203 .
... Have all passengers
lea ve the veh icle and
stay away from the danger zone¢.&_ .
... Take the
sea lant bottle and the ele ctri c air
pum p from the luggage compartment un-
de r the floor ¢ page 203, fig. 152. ....

.. Remove the "max. 50 mph" (80 km/h)
sticker from the sealant bottle and affix it to
the instrument cluster in the dr iver's view.
A WARNING
- Turn the hazard flashers on if you have a
flat tire in moving traffic. In this way you
protect yourself and other road users .
- Make sure that all passengers are in a
safe place, out of the dange r zone (fo r
example, behind a guard ra il).
(D Note
Part icular care is necessary if you are mak­
ing a t ire repair on a steep incline.
@ Tips
Obey all laws.
Making a tire repair
Tire repair consists of the following sections.
F ig. 154 Parts of the Tir e Mob ility System
Fig . 1 55 Con nector for the Ti re Mob ility System
l) The e lectr ic a ir pump s houl d never r un for long er than
8 m inute s.
What do I do now ? 205
Assembling Ti re Mobility System
.. Open the lid@ of the e lectr ic air p ump
<:!) fig. 154 .
.. Pull the plug @and the pressure hose ®
w ith the gauge out of the housing .
.. Screw the pressure hose ® of the electric
air pump onto the flange @ of the sealant
bott le @ .
.,. Push the sea lant bottle w ith the flange
down into the recess ® on the lid of the
electric a ir pump.
.. Remove the d ust cap from the va lve of the
defe ctive tire .
.. Screw the hose(§ onto the va lve
0
c::> fig. 155.
.. Insert the plug@¢ fig. 154 into the socket
for the c igarette lighte r.
Inf lating tire
.. Move the switch @ ¢ fig. 155 on the elec­
tric air pump
l} to position I. After 5 mi­
nutes, tire pressure m ust have reached at
least 1.8 bar .
.. Switch the e lectric air pump off -sw itch in
position
0 . If the required tire pressure of at
least 1.8 bar has not been reached, follow
th e instruct ions in the section
Re-inflating
tire .
Re-inflating tire
.. Remove the hose from the valve and pull
the plug out of the socket.
.. Dr ive the veh icle slowly 10 meters back­
ward o r fo rward . This helps to d istribute the
sealant bette r .
.. Remove the empty infla tion bot tle and
s crew the hose ®® ¢
fig. 154 from the
electric pump directly onto the va lve .
.. Insert the plug @ into the socket for the
cigarette lighter .
.. Move the switch @
c::> fig. 155 on the elec­
tr ic air pump
l} to position I. After 5 mi­
nutes, tire pressure must have reached at
least 1.8 bar.

206 What do I do now?
• Switch the electric air pump off -switch in
position
0. If the required tire pressure of at
l east 1.8 bar has not been reached, it is not
poss ible to make a repa ir with the tire seal­
ant. Seek professional ass istance.
Disassembling Tire Mobility System
• Remove the hose from the valve and pull
the p lug out of the socket .
• Screw the dust cap onto the valve.
• Place the empty sealant bottle back in the
original packaging and clip it in place under
the floor so that no tire sealant can run out into the vehicle .
• Start driving r ight away so that the sealant
is distributed in the tire.
.&_ WARNING
- Follow the manufactur er's safety instruc­
tions on the decal for the air pump and
the sea lant bott le .
- If a tire pressure of 1.8 bar cannot be
achieved after pumping for 5 minutes,
the tire is too severely damaged. Do not continue to drive.
- Seek professional assistance if it is not
possible to repair the tire with the tire
sealant.
(D Tips
- Do not operate the electric air pump for
more than 8 min utes without stopping,
otherwise it can overheat. When the air
pump has cooled down, you can continue
to use it.
- If sealant has escaped, allow it to dry,
then you can peel it off.
Final check
After driving for a short distance, t ire pressure
must be checked .
• After driving for about 10 minutes, stop
and check the t ire pressure .
• If tire pressure is still at least 1.3 bar, in­
flate the tire to specified p ressure (see driv­
er's side B-pillar), drive to the next repair shop and have the tire and the sealant
bot­
tle replaced.
• If tire pressure is less than 1.3 bar, the t ire
is too severely damaged. Do not continue to
drive. Seek professional assistance.
.&_ WARNING
If tire pressure is less than 1.3 bar after
driving for 10 minutes, the tire is too se­
ve rely damaged. Do not continue to drive.
Seek professional assistance.
(D Tips
After a tire repair, have the sealant bottle
replaced at a dealership. This restores full
functionality to the Tire Mobility System .
What should I be
aware of when
changing a tire?
Tires with unidirectional tread design
-
Tires with unidirectional tread design must be
mounted with their tread pattern pointed the
right direction.
A unidirectional tire can be identified by ar­
rows on the sidewall, which point in the direc­
tion of the rotation. You must follow the
specified direction of rotation. This is necessa­
ry in order for these tires to develop their op­
timum characteristics regarding grip, road
noise, wear, and hydroplaning .
· Anti-theft wheel bolts
A special adopter is needed to turn the anti­
theft wheel bolts.
Fig . 156 A nti-theft wheel bolts wit h adapte r