2012 AUDI A3 tool kit

102 Transmi ssion
the warning does not turn off, do not continue
driving . See your authorized Audi dealer or
qua lified repair fac ility for assistance. Other ­
wise serious transmission damage could re­
sult. Once the indicator light has turned off,
drive to your authorized Audi dealer or quali­
fied repair fac ility immediately to have t he
malfunction corrected.
Emergency release for selector lever
Appl ies to vehicles: with S tro nic®
If the vehicle's power supply fails, the selec­
tor lever can be released in an emergency.
Fig. 115 Selector lever: Remove selector lever sleeve
Fig . 1 16 Selecto r lever : emerge ncy release from the
Park pos it io n
The emergency release mechanism is located
on the right front under the selector lever
shift gate. The release procedure requ ires pro ­
fess iona l dexterity . We recommend that you
seek assistance .
Removing the selector lever boot
.,. Engage the parking brake .
.,. Remove the screwdriver from the vehicle
tool kit . Use the flat side of the reversib le
screwdriver blade¢
page 234 .
.,. Carefully pry the cover out w ith the sc rew­
dr ive r and pull it¢
fig. 115 towa rd the shift- er
knob in the direction of the arrow . The
screwdriver must grip at the lower edge of
the cover to loosen it .
Emergency rel ease for selector lev er
.,. Press t he ye llow release lever in the direc ­
tion of the arrow ¢
fig. 116 and hold it in
that position.
.,. Press t he re lease button in the selector lev-
er @ and move the lever into the N position.
.,. Clip the s hift boot back into the shift gate.
If the vehicle has to be pushed or towed if the
power supply fai ls (e.g. battery is discharged),
the selector lever must be moved to the N po­
s ition using the emergency locking device.
A WARNING
-The selector must only be shifted from the
P position if the handbrake is firmly ap­
p lied. Otherwise the vehi cle wou ld start
moving unexpe ctedly on a grade when the
se lec tor lever is s hifted from the P pos ition
- increasing the risk of an accide nt.

-For your safety, we strongly recommend
that you do not travel with a portable
fuel container in your vehicle. The con­
tainer, full or empty may leak and could
cause a fire, especially in a crash.
- If, under exceptional circumstances, you
must transport a portable fuel container
'
please observe the following:
- Never fill a portable fuel container
while it is anywhere in or on the vehicle (for example, in the luggage compart­
ment, or on the trunk) . Static electrici­
ty can build up while filling and can ig­
nite fuel vapors causing a fire.
- Always place a portable fuel container
on the ground before filling .
-Always keep the filler nozzle complete­ ly inside the portable container before
and during filling.
- If filling a portable container made of metal, the filler nozzle must always be
in contact with the container. This will
help prevent static electricity from dis­
charging and cause a fire.
- Never spill fuel inside the vehicle or
luggage compartment. Fuel vapors are
highly flammable.
- Always observe local and state/provin­
cial laws regarding the use, storage
and transportation of fuel containers.
- Make certain the fuel container meets
industry standards (ANSI/ ASTM
F852-86).
(D Note
- If any fuel has spilled onto the car, it should be removed immediately to pre­
vent damage to the paint.
- If the fuel tank runs completely empty in
a vehicle with a
diesel engine, the igni­
tion must remain switched on for at least 30 seconds after refueling before
starting the engine.
It may take longer
than usual for the engine to start, even
up to a minute. This is because the air
must first bleed out of the fuel system
when starting the engine.
Fuel supply and filling your fuel tank 193
@) For the sake of the environment
As soon as the correctly operated nozzle
switches off automatically for the first
time, the tank is full. Do not try to add
more fuel because fuel may spill out. In
addition, the expansion space in the fuel
tank will be filled -causing the fuel to
overflow when it becomes warm and pol­
lute the environment.
(0 Tips
-Running your engine while refuelling
may cause vapors to escape or even fuel
to spill out of the tank. This would then
shut off the fuel nozzle before the tank
is full.
- Do not refuel your vehicle with the igni­
tion switched on. The fuel gauge may
otherwise not indicate the correct fuel
level after refuelling.
Unlocking the fuel filler flap by hand
You can open the fuel filler flap by hand if the
power locking system should fail.
Fig. 154 Inside the luggage compartment : Openi ng
the fuel fi lier flap
by hand
.,. Open the rear lid.
.,. Remove the screwdriver from the vehicle
tool kit
¢ page 234.
.,. Use the screwdriver (vehicle tool kit) to pry
the cover off at the recess
¢ fig. 154 (D .
.,. Pull the actuator in the direction of arrow
@ to release the fuel filler flap¢
fig. 154.
.,. Open the fuel filler flap .

234 What do I do now ?
What do I do now?
Jack, tools and spare
wheel
Jack and tools
The tools and jack are stored underneath the
floor panel in the luggage compartment.
Fig . 178 Floor panel hung on the bottom of the lug­
gage compartment cover
Fig. 179 Vehicle tool kit and jack
~ Raise the floor panel w ith the loop.
~ Hang the loop on the underside of the lug-
gage compartment cover
Q fig. 178.
~ Remove the too l kit or the jac k.
The onboard tool kit incl udes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt covers
- Wheel bolt wrench
- Alignment p in for changing wheels
- Screwdriver w ith reve rsible blade
- T owing eye
Before storing the jack, make sure it is wound
back down as far as it will go.
After u se , th e jack and tool s mu st be put
b ac k in pl ace under nea th t he floo r pan el in
t he luggag e comp artmen t.
Note: some of the on -board items listed
above are provided on certain mode ls only or
are optiona l extras.
A WARNING
-Improper use of the vehicle jack can cause
serious personal injuries.
- Using a bumper jack to raise the vehicle
will damage the bumper system. The
jack may slip, caus ing injury.
- Never support your vehicle on c inder
b locks, br icks or other objects. These
may not be able to support the load and
could cause injury when they fail.
- Never start or run the eng ine while the
veh icle is supported by the jack.
- If you must work under the veh icle, al­
ways use safety stands specifically de­ signed fo r th is purpose.
- Never try and use the hexagonal socket
in the handle of the screwdriver to loos­
en or tighten the whee l bolts.
- Always make sure the spare tire and even
a flat tire are secured in place and not
loose, otherwise they cou ld fly forward,
causing pe rsonal i njury to passengers in
the vehicle in an accident or sudden ma­
neuver.
- Neve r use the ja ck supplied with your Au­
d i on another vehicle, particularly on a
heav ier one. The jack is only s uitable for
use on the vehicle it came with.
Compact spare wheel
Applies to veh icles: w ith compact spare whee l
The compact spare wheel is only intended to
be used for a short time.
Fig . 180 Compact spare wheel in the wheel well

2. Loosen the w hee l bol ts ¢ page 238.
3. Locate the proper mounting point for the
jack and align the jack below that point
¢ page 239.
4. Lift the car with the jack¢ page 239.
5. Take the flat wheel off and then put the
spare on
¢ page 240 .
6. Tighten all wheel bo lts light ly .
7 .
Low er the veh icle w ith the jack.
8 . Use the wheel bolt wrench and
firml y
tighten all whee l bolts ¢ page 238.
9. Put the decorative wh eel cov er* back on.
A WARNING -
Always read and head all WARNINGS and
information
¢ A in Raising the vehicle on
page 240
and ¢ page 241.
After changing a wheel
A wheel change is not complete without the
following actions .
.. Store and secu re the replaced wheel in the
spare wheel we ll.
.. Put the tool case and the jack back in place
in the luggage compartment .
.. Check the
tir e pres su re on the spare wheel
immediately after mounting it .
.. As soon as possible, have the
tightening
torqu es
on all wheel bolts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lb (120 Nm).
.. Have the flat tire
repl aced as soon as possi ­
ble.
@ Tips
- If yo u n otice wh ile chang ing a tire tha t
the wheel bo lts a re cor roded and diffi ­
cult to turn, then they should be re­ placed before you check the tightening
torque.
- Drive at reduced speed until you have the
tightening torques checked .
What do I do now ? 237
Full wheel covers
App lies to vehicles : with ful l wheel cove rs
T he wheel covers must be removed to access
the wheel bolts.
Remo val
.. Pull the full whe el cover off manua lly.
Installation
.. First press the full w hee l cover on to the rim
a t the cut-o ut prov ided for the va lve . Then
engage the outer edge of the
full wheel cov ­
er
in the steel rim.
Decorative wheel covers
App lies to vehicles: with decorat ive w hee l covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 181 Whee l cha nge : removing the whee l cover
Remo ving
.. Insert the hook provided with the on board
tool kit into the hole on the center hub
piece.
.. Pull off the
decorati ve wh eel cover
¢ fig . 181 .

238 What do I do now?
Wheels with cap-covered wheel bolts
Applies to vehicles: wit h cap-cove red w hee l bo lts
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig. 182 Whee l change : removing the wheel bo lt caps
Removing
.,. Push the plastic clip provided w ith the on­
board tool kit down over the wheel bolt cap
u nt il it engages .
.. Pull on the properly engaged
plastic clip to
extract the cap
¢ fig. 182 .
Refitting
.. Place the caps over the wheel bolts and
push them back in .
The caps are there to p rotect and keep the
wheel bolts clean.
Anti-theft wheel bolts
Applies to vehicles : wit h ant i-t heft wheel bo lts
To tighten or untighten the anti-theft wheel
bolts you must use a special adapter.
(~
'
Fig. 183 Anti-theft w hee l bo lt w it h cap and adapter
.. Remove the cap* ¢fig. 183 @using the
plastic clip found in the vehicle tool kit. ..
Insert the adapter @ as far as it will go into
the anti -theft wheel
CD bolt.
.. Push the socket wrench over the adapter
@ .
.. Loosen or tighten the wheel bolt
¢page 238.
To remove the cap* @, make sure the plastic
clip is pushed in as far in as possible until it
lines up with the edge of the cap .
We recommend you keep the whee l bolt
adapter in the tool kit.
T he
code number of the wheel bolt lock is
stamped on the front side of the adapter . You
will need this number in order to get a re­ placement from your authorized A udi dealer.
Q) Tips
Write down the code number and keep it
in safe place. Do not keep it in the vehicle.
Loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
Fig. 184 W hee l change : loosen ing the wheel bolts
Loosening
.,. Fit the wheel bolt wrench over the wheel
bolt and push it down as far as it will go .
"' ... -cL a, a,
.,. Close your g rip around the end of the
w rench handle for maximum torque and
turn the wheel bolts
counter-clockwise
about one single turn in the direction of ar-
row ¢
fig. 184. .,.

240 What do I do now?
& WARNING
-You or your passengers could be injured
while changing a wheel if you do not fol ­
low safety precautions:
- Mounting the jack under the vehicle at
any other place than indicated above
may damage the vehicle or may result
in personal injuries .
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack. Always provide a firm base for
the jack on the ground . If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping .
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you a re
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the roadway and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
raise the jack.
Taking the wheel off/putting the spare
on
Follow these instructions step-by-step for
changing the wheel
Fig. 187 Wheel c han ge: using the sc rewdrive r handle
(w ith the blade removed) to turn the bolts
... ,._
"' i
"'
Fig. 188 W hee l change : alignmen t pin inside the top
hol e
M ,._
"' d. 00
"'
After you have loosened all wheel bolts and
jacked the vehicle off the ground, perform the
following steps to remove and replace the
wheel:
Removing the wheel
.,. Use the hexagonal socket in the screwdriv·
er handle
to completely turn out the top­
most wheel bolt and set it aside on a
clean
surface c;, fig. 187 .
.,. Screw the threaded end of the alignment
pin from the tool kit hand-tight into the
now vacant bolt hole <=>
fig. 188 .
.,. Then completely unscrew the other wheel
bolts as described above.
.,. Take off the wheel leaving the alignment
pin in the bolt hole
c;, &,.
Putting on the spare
.,. Lift the spare wheel up and carefully slide it
over the alignment pin to guide it in place .
.,. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly .
.,. Unscrew the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest.
.,. Turn the handle on the jack counter-clock­
wise to lower the vehicle until the jack is
fully released .
.,. Use the wheel bolt wrench to tighten all
wheel bolts firmly
r:::;, page 238 . Tighten
them
crosswise , from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.

252 Emergency situations
A WARNING
If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potential risk of an
accident .
Rear towing loop
Do not install the rear towing loop until it is
needed.
Fig. 196 Rear bumper: cover
Fig. 197 Rear b umper: t owing loop inser ted
On the right side of the rear bumper there is a
threaded hole for the towing loop. The
threaded hole is behind a cover. Note that the
towing loop has a
left-hand thread!
.. Remove the towing loop from the veh icle
toolkit ¢
page 234 .
.. Place the screwdriver against the upper
edge of the cover and carefu lly pry it out
¢ fig. 196.
.. Insert the towing loop into the threaded
hole ¢
fig. 197 and turn it all the way in un­
til it is seated securely , then tighten it with
the wheel bolt wrench .
When it is no longe r needed, unscrew the
towing loop and put it back into the vehicle toolkit.
Be sure to have the towing loop stored
in the vehicle at a ll times.
A WARNING
--
If you do not screw the towing loop com-
pletely, it could come out of the threaded
hole while the vehicle is being towed caus­
ing damage to the vehicle and possible se ­
rious personal injury .
Loading the vehicle onto a flat bed truck
Fig. 198 Vehicle on flat bed truck
Front hook up
.. Align the vehicle with the centerline of the
car carrier ramp .
.. Attach the winch hook to the front towline
eye
¢page 251, fig. 195 previously instal­
led .
Rear hook up
.. Align the vehicle with the centerline of the
car carrier ramp .
.. Attach the winch hook to the rear towline
eye¢
page 252, fig. 197 previously instal­
led .
(D Tips
Check carefully to make sure the hook-up is secure before moving the car up the flat­
bed truck ramp .
Lifting the vehicle
Important safety precautions
Be aware of the following hazards before lift­
ing the vehicle with a workshop hoist or floor
jack: ..,.