2012 AUDI A3 length

26 Driver information d isplay
Total-trip memory (Trip computer 2)
Unlike the sing le- tri p memory, t he tota l-trip
memory is not reset automatically. This per ­
mits you to eval uate your d riving data for the
enti re pe riod between manual resets.
Fuel range
T he e stima ted cruising r ange in mile s (km)
a ppears in the d isplay. The disp lay ch anges in
increments of 6 miles ( 10 km).
Average fuel mileage
The average fuel economy in MPG (l/ 100 km)
si nce you last clea red the memory appears in
this displ ay .
Current fuel mileage
T he instantaneous fuel consumption in miles
pe r gallo n (l/ 100 km) is shown in this d isplay.
When the ve hicle is stationary, the most r e­
cent fuel co nsump tion is di splayed.
Average speed
The average speed in mph (km/h) since the
last time the disp lay was reset appea rs i n the
d isplay .
Elapsed time
The length of time that you have been driving
since you last reset the memory appears in
this display. T he maximum time period that
can be recorded is
999 hou rs and 59 mi nutes .
Distance
The elapsed distance since the last time the
memory was cleared appears in the display .
The maximum d istance that can be recorded
i s
9,999.9 m iles (9,999 .9 ki lometers).
@ Tips
A ll st ored values will be lost if the vehicle
battery is disc onnected .
Operation
The trip computer is controlled by two
switches on the windshield wiper lever .
Fig . 11 W ipe r arm/w iper lever: co ntro ls for the t rip
compute r
Selecting the trip computer
.. Tap the I Rese t I button @ until the trip com­
puter (memory leve l 1 or 2) appears in the
disp lay
c> page 25, fig. 10.
Selecting the functions
.. Push in t he up per (lower) protr usio n on t he
fu nction selector sw itch ®
c> fig . 11 . The
functi ons fo r th e tr ip comp ute r are dis­
played in succession on t he respective mem­
ory leve ls.
Resetting the fun ction to zero
.. Push the I Res et I butto n @ for at least two
seconds .
You can re se t the following values to zero us­
ing t he
I R eset I bu tton :
- driving time
- distance
- average fuel m ileage
- average speed
T he trip computer on ly o perates whe n the ig­
nit ion is on. When you turn o n the ign ition,
the f unction that was in use when you last
turned the ignition off will be displayed .
(D Tips
-Yo u can also set the va lues for t he func ­
tions to zero i n the me nu disp lay
( Reset )
c>page27 . .._

32 Driver information display
8.18, (Canada models) Speed warning 2
Storing warning 2 is recommended if you al­
ways
want to be reminded of a certain speed,
for example when you are traveling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a specified
speed for winter tires.
The speed warning 2 symbol ,
[I/ [9] (Canada
models) appears in the display when you ex­
ceed the stored speed limit. Unlike warning 1, it will not go out until the vehicle speed drops
below the stored speed limit .
Setting speed warning 2
¢ pag e 32.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you shou ld still
watch the speedometer to make sure you
are not driving faster than the speed limit.
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the button.
Fig. 23 Sectio n of inst rume nt cl uste r: Set/Check but­
to n
Storing the maximum speed
11o-Drive at the desired maximum speed.
11o-Press the knob button ¢ fig. 23 until the
q page 31, fig. 22 symbol appears.
Resetting the maximum speed
.. Drive the vehicle at a speed of at least
3 mph (S km/h)
11o-Press the knob for more than 2 seconds.
The speed warning symbol
[I (USA models)/
ISl (Canada models) will appear briefly in the
d isplay when you release the button to indi- cate that
the maximum speed has been stored
successfully .
T he maximum speed remains stored until it is
changed by pressing the button again briefly
or until it is deleted by a lengthy push on the
button.
Speed warning 2: setting a speed limit
Switches in the wiper arm ore used to operate
warning threshold
2.
Fig. 24 W ipe r leve r: Trip compute r co ntrols
To store maximum speed
.. Turn off the ignition .
11o-Briefly press the button in the instrument
cluster ¢
page 32, fig . 23. The odometer
and the dig ital clock are now illuminated .
11o-Press the button for at least 2 seconds . The
current ly sto red max imum speed appears in
the display or the crossed out symbol for
warn ing thresho ld 2, if no maximum speed
was set previously .
.. Press the function selector switch in the
wiper
lever @qfig. 24 up or down to
change the set value. Va lues run up or down
in steps of 6.2 mph (10 km/h).
To delete maximum speed
.. Turn off the ignition.
.. Briefly press the button in the instrument
cluster ¢
page 32, fig. 23. The odometer
and the digital clock are now illuminated .
.. Press the button for at least 2 seconds. The
currently stored max imum speed appears in
the display .
II>

48 Clear vis ion
light sensor checked as soon as possible at a
dea lership.
Com ing home /leaving home function *
The function is switched on when the switch is
i n the AU TO* position and the function is
shown as active in the driver info rmation sys­
tem .
The
co ming h om e function illuminates the
a rea around the veh icle when the ign it ion is
switched off and the driver 's door is opened.
The length of time the lights remain on can be set in the menu display
( Illumination > Exte­
r io r light s> coming hom e).
The leav ing home function illuminates the
area around the vehicle when unlock ing it.
A WARNING
- Never use dayt ime running lights to see
where you are going. They are not bright
enough and w ill not let you see far
enough ahead for safety, especially at
dusk or when it is dark. Always switch on
the low beams at dusk or when it is dark.
- Automatic headlights are only intended
to assist the dr iver . They do not relieve
the driver of his responsibility to check
the headlights and to tu rn them on man­
ually according to the current light and
visibili ty cond itions. Fo r example, fog
and rain cannot be detected by the light
sensors . So a lways switch on the head­
lights under these weather cond itions
and when driving in the dark
io.
- Crashes can happen when yo u cannot see
the road ahead and when you cannot be seen by other motorists .
- Always turn on the headlights so that
you can see ahead and so tha t others
can see yo ur car from the bac k.
- With the switch in
AUTO front fog lights
ca nnot be t urned on in addition .
- The light sensor fo r headlight contro l is
l ocated in the rear view m irror mount .
Do no t apply any stickers to the w ind- shield in this area to prevent malfunc
­
tions or fa ilures.
- Some exter io r light ing funct ions can be
adjusted in the driver informat ion sys­
tem
~ page 2 7.
- If you remove the ignition from the igni ­
tion lock while the headlights are still
on, a buzzer will so und as long as the
dr iver's door is open to rem ind you to
turn off the lights.
- Always observe the specif ic loca l regula­
tions for your area as to when to use your
lights.
- With automatic headlights, the high­
beam funct ion is also available, but wit h
one restrict ion: If you have not switched
the high beams back to low beams dur­
ing automatic headlight operation (fo r
example, after d riving through a tunnel) ,
only the low beams come on the nex t
t ime au tomati c headlights are swi tc h ed
on. To use the high beams, you first have
to pull the high beam lever back and
then push the lever fo rward again.
- In cool or damp weather , the inside of
the headlights, turn signals and tail lights can fog over due to the tempera­
ture difference between the inside and
outside. They w ill clear shortly after
switching them on. This does not affect
the se rv ice life of the lighting .
- Frequent use of the coming home/leav ­
ing home function for app roach ing and
depa rting a vehicle parked in the da rk
w ill strain the battery . Thi s ap plies pa r­
tic ular ly if only short distances a re d riven
between stops . Occasionally drive longer
dis tances to make sure the battery is re ­
charged sufficiently.

58 Clear vis ion
Removing the wiper blade
.. Move the wipers to the service position
c::>page 57.
.. Fo ld the windshield wiper arm away from
the g lass.
.. On the upper end of the wiper arm at the
corrugation, squeeze the plast ic retainer to­
gether on both sides in the direction of the
arrow
c::> fig. 59 .
.. Rotate the w iper blade in the direct ion of
the arrow @c::>
fig. 60 away from the w iper
arm.
.. Lift the w iper blade
off in the direc tion of
the arrow @.
Attaching the wiper blade
.. Place the rounded end of the wiper onto the
end of the w iper arm in the
oppo site direc­
t ion to the ar row @
c::> fig. 60.
.. Swing the wipe r in the oppo site direct io n to
the arrow @onto the wiper arm.
.. Sq ueeze the corrugation on the w iper until
yo u hear it click in the wiper arm.
.. Fold the wiper arm back onto the wind­
shield .
.. Switch the ignition on and move the w iper
lever down briefly . The wiper will move back
to the park pos it ion .
The front wiper b lades measure left s ide
23 .20 in . (S90 mm) and rig ht side 18 .SO in.
(470 mm) i n length,
C lean your wiper blades regu larly with a wind­
shie ld washer solution to prevent streaking . If
the blades are very d irty, for example with in­
sects, carefu lly clean the blades w ith a sponge
or a soft b rush.
If the wiper b lades beg in to streak the wind­
shield, this could be caused by res idue left on
the w indshield by automat ic car washes .
F ill the windsh ield washer container with a
specia l so lution available at your author ized
Aud i deale r to remove the residue .
Be s ure to inspect the condition of your w iper
b lades regularly. For safety reasons, replace
your w iper blades once or twice a year if nee- essa
ry . See yo ur authorized Aud i dea ler for re ­
placement blades .
A WARNING
-- Clean your w iper blades reg ularly with a
w indshie ld washer so lution to prevent
streaking. If the w iper blades are very
d irty, fo r example with insects , ca refully
clean the wiper blades wi th a sponge or a
soft brus h .
- For your safety , you should replace the
wiper blades onc e or twice a year . Se e
your aut hor ized Audi dealer for replace­
men t blad es.
0 Note
-The wiper b lades may only be c hanged
c::> page 57 in the service posit ion! Ot he r­
w ise, you risk damag ing the pa int on t he
hood or the w indshie ld wi per mo to r.
- Yo u should not move your veh icle o r
press t he winds hield wiper leve r when
t he wipe r arms are folded away from the
w indshield. The windsh ield wipers wo uld
move back into their or iginal position
and co uld damage the hoo d and wind­
shield.
- To help prevent dama ge to the w iper sys­
tem, always loosen blades which are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper b lades,
do not use gaso line, kerosene, paint
thinner, or other solvents on o r near the
w iper blades .
- To help prevent damage to the w iper
arms or other components, do not at­
tempt to move the wipe rs by hand .
(D Tips
-Commercial hot waxes applied by auto­
matic ca r washes affect the cleanability
of the g lass s urface .
- Yo u can also use the service position, for
examp le, if yo u want to p rotect the
w indshield from icing by using a cover. ..,_

-Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
&
Maintenance booklet.
- Lack of proper maintenance as well as
improper use of the vehicle will impair
the function of the emission control
system and could lead to damage.
@ For the sake of the environment
Even when the Emission Control System is
operating properly, the exhaust gas can
have a sulfur-like exhaust gas smell under
some operating states. This depends on
the sulfur content of the fuel being used .
Using a different brand of fuel may help,
or filling the tank w ith lead-free super
grade gasoline.
Diesel particulate filter
Ap plies to vehicles: with diesel partic ul ate filter
The diesel particulate filter filters nearly al l of
the soot part icles out of the exhaust. The fi l­
ter cleans itse lf automatically under normal
driving conditions . If the fi lter cannot clean it­
self (for example, because you are only driving
short distances), the filter becomes clogged
with soot and the
II symbol for the diesel
particulate filter illuminates
c> page 22.
A WARNING
- Do not park your vehicle over flammable
materials such as grass or leaves because
the high temperature of the diesel par­
t icu late filter could start a fire .
- Do not apply an underbody protectant in
the exhaust system a rea or a fire could
start.
(D Tip s
-When the diesel particulate filter be­
comes saturated, the engine speed in­
creases to approximate ly 1,500 rpm
while the vehicle is in motion to init iate
the cleaning of the diesel particulate fil­
ter a utomatically without the warning
l amp lighting up . If the warning lamp
Dri vin g and en vironm ent 171
Ill sti ll appears, you shou ld drive to a
qualified workshop .
Avoid damaging the
vehicle
When you are driving on poor roads, or over
curbs, steep ramps, etc., make certain that
low -lying parts such as spo ilers and exhaust
system parts do not bottom out and get dam­
aged.
This is espec ially true for veh icles with low­
slung chassis (sports chassis) and fully loaded
vehicles.
Operate your vehicle
economically and minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex­
haust and noise Levels.
Fuel economy, env ironmenta l impact, and
wear on your eng ine, brakes and tires largely
depend on three facto rs:
- your personal driving style
- operating conditions
- technical limitations
If you ant ic ipate wha t you need to do next and
drive economically, you can easily cut your
fuel consumptio n by 10-15 percent . This sec­
tion wi ll give you some tips on how you can
help the env ironment and your pocketbook.
(D Tips
The consumption estimates as published
by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, which will vary depending upon vehi­
cle load and speed, road and weather con­
dit ions, trip length, etc.
•
•

@ Tips
-Where snow chains are mandatory on
certain roads, this normally also applies
to vehicles with All Wheel Drive .
- If snow chains are insta lled, the tire
pressures shou ld not be stored in the tire
pressure monitoring system (TPMS).
Otherwise the system could malfunction
¢page 232.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of whee l bolts is matched to the
factory installed rims. If different rims are fit­
ted, the correct wheel bolts wit h the right
length and correctly s haped bolt heads must
be used. This ensures that wheels are fitted
secure ly and that the bra ke system f unctions
cor rectly .
In certain circumstances, you may not use
wh eel bolts from a differ ent vehicle -even if it
i s the same mode l.
.&, WARNING
Improperly tig hte ned o r maint ained wheel
bol ts can become loose ca using loss of
cont ro l, a co llision and ser ious persona l in ­
jury.
- Always keep the wheel bolts an d the
threads in the wheel hubs clean so the
whee l bolts can tu rn easily and be pro p­
er ly t ightened.
- Never grease or oil the wheel bo lts and
the threads in the w heel hubs. They can
become loose w hile driving if greased or
o iled, even if tightened to the specified
torq ue.
- Only use wheel bolts t hat belong to the
r im being installed.
- Never use different whee ls bolts on your
vehicle.
- Always maintai n the co rrect tighten ing
torq ue for the wheel bo lts t o reduce the
risk of a wheel loss. If the tightening tor-
Tire s an d wheel s 229
que of t he whee l bolts is too low, they
can loosen and come out when the vehi­
cle is mov ing. If the tig htening torq ue is
too high, the wheel bolts and threads
can be damaged and the whee l can be­
come loose.
(D Note
The specified torque for the whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm). Torq ue whee l bolts diago­
nally. After changing a whee l, the tor que
must be checked as so on as possible with a
torq ue w rench -prefe rably by an au thor ­
iz ed A udi de aler or qu alified workshop .
Low aspect ratio tires
Your Audi is factory -eq uipped w ith low aspect
r atio tires . These tires have been tho ro ughly
tested and been se lected specifically for your
model for their superb performance, road fee l
and handli ng u nder a var iety of driving condi­
tions . Ask your au thorized Aud i dealer for
more d etails.
The low aspect ratio of these t ires is ind icated
by a numeral of
55 or less in the tire's s ize
designation . The numera l represen ts the ratio
of the t ire's sidewa ll height in relation to its
t read width exp ressed in perce ntage. Conven­
tiona l tires have a he ight/w idth ratio of 60 o r
more.
The performance of low-a spect-ratio tires i s
particularly sensitive to improper inflation
pre ssure.
It is therefore important that low
aspect ratio tires are inflated to the specified
pres sure and that the inflation pressure is
regularly checked and maintained. Tire pre s­
sures should be checked at least once a month and always befo re a long trip
¢ page 218, Checking tire pressure.
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged mo re
easily by impact w it h potholes, curbs, gul lies ..,.
•
•

258 Data
140 hp, 2.0 TOI liter 4-cyl. turbo clean diesel
engine
App lies to vehicles: with 2.0 liter TD! 4-cyl. clea n diesel engine,
Engine dat a
Maximum ou tpu t SA E ne t hp@rpm 140 @42 00
Maximum torque SAE net lb-ft@ rpm 236@ 1750 -2500
N o. of cylinders 4
Displacement CID (cm3
) 120.1 ( 1968)
Stroke i
n (mm) 3.7 6 (9 5.5)
Bore i
n (mm) 3.19 (8 1.0)
Compression ratio 16.5: 1
Fuel ULSD Diesel No . 2 Further details c::> page 190, Diesel fuel
Dimensions (approx .)
Length (with license plate bracket) in (mm)
Width (across mirrors) in (mm)
Height (unladen, incl. roof ra ils) in (mm)
T urning circl e diameter (curb to curb) ft. (m)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity)
Windshield washer fluid container
Engine oil
with filter change
168.9 (4 292)
78.5 (1995)
56 .0 (1423)
35.1 (1 0.7)
gal/li te rs 1 4 .63 / 55.0
ga I/liters 1.8/7 .0
quarts/liters 3.1 / 3.0
quarts/liters 4 .2 I 4.0