2012 Acura MDX Owner's Manual

Customize SettingsWhen the main menu displays
‘‘Keyless Memory Settings™,’’you
can customize some vehicle control
settings.
To enter the customizing mode,
press the SEL/RESET button.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park.If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shift lever out
of Park, the display will change to the
normal screen.
You can customize some vehicle
control settings for‘‘DRIVER 1’’and
‘‘DRIVER 2’’separately. If‘‘DRIVER
1’’or‘‘DRIVER 2’’is not displayed,
customizing is not possible.
To have the driver's ID detected,
make sure your remote transmitter is
linked to the system (see Keyless
Memory Settings™on page 148).
If you want the settings as they were
when the vehicle left the factory,
select DEFAULT ALL, as described
on page 93.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
Refer to the table on the following
pages about the settings you want to
customize.
Multi-Information Display90

Group Setup Menu Item Description Setting Option Page
ACC SETUP
(P. 96)PRE-RUNNING CAR DETECT
BEEPCauses the system to beep when a vehicle ahead of
you gets too close.ON
ᤳ1
97
OFF
ACC DISPLAY SPEED UNIT Changes the ACC display speed unit. mph
ᤳ2
previous
setting98
km/h
ᤳ3
METER SETUP
(P. 99)LANGUAGE SELECTION Changes the language used in the display. ENGLISH
ᤳ1
100 FRENCH
SPANISH
ADJUST OUTSIDE
TEMP. DISPLAYChanges the outside temperature reading above or
below its current reading.－5°F～ᤣ0°F
ᤳ2～5°F
101
－3°C～ᤣ0°Cᤳ3～3°C
TRIP A & AVG. FUEL
RESET with REFUELCauses trip meter A and the average fuel economy to
reset when you refuel.ON 102
OFF
ᤳ1
ADJUST
ALARM VOLUMEChanges the indicator alarm volumes into three levels. HIGH
103 MID
ᤳ1
LOW
ELAPSED TIME RESET Resets the elapsed time of your current trip. MANUAL ONLY
104 IGN OFF
ᤳ1
TRIP B
TRIP A
AUTO INTERIOR
ILLUMINATIONChanges the interior light sensitivity to your liking. MAX LOW
105 HIGH MIN
MID
ᤳ1
OFF
POSITION SETUP
(P. 107)MEMORY POSITION LINK Changes the driver's seat, the steering wheel, and the
outside mirror positions to a stored setting.ON
ᤳ1
108
OFF
AUTO TILT & TELESCOPE
STEERING WHEELMoves the steering wheel fully in and up when the key
is removed.ON
ᤳ1
109
OFF
ᤳ1: Default setting
ᤳ2: Default setting for U.S. models
ᤳ3: Default setting for Canadian models
CONTINUED
Multi-Information Display
91
Instruments and Controls

Group Setup Menu Item Description Setting Option Page
LIGHTING SETUP
(P. 110)INTERIOR LIGHT
DIMMING TIMEChanges how long (in seconds) the interior lights stay
on after you close the doors and the tailgate.60 sec 15 sec 111
30 sec
ᤳ
HEADLIGHT
AUTO OFF TIMERChanges how long (in seconds) the exterior lights stay
on after you close the driver's door.60 sec
112 30 sec 0 sec
15 sec
ᤳ
AUTO LIGHT
SENSITIVITYChanges the timing of when the headlights come on.
The headlight switch needs to be in the AUTO
position.MAX LOW
113 HIGH MIN
MID
ᤳ
DOOR/WINDOW
SETUP
(P. 115)AUTO DOOR LOCK Changes the setting of when to automatically lock the
doors.SHIFT FROM P
116 WITH VEH SPD
ᤳ
OFF
AUTO DOOR UNLOCK Changes the setting of when to automatically unlock
the driver's/all the doors.SHIFT TO P
ᤳ
DRIVER
DOOR/ALL
DOORS
117 IGN OFF
OFF
KEY AND REMOTE
UNLOCK MODEChanges which doors unlock with the remote
transmitter on a first push.DRIVER DOOR
ᤳ
119
ALL DOORS
KEYLESS LOCK
ACKNOWLEDGMENTThe exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also sound
when you press the LOCK button twice.ON
ᤳ
120 OFF
SECURITY RELOCK TIMER Changes how long it takes (in seconds) for the doors
to relock and the security system to set after you
unlock but do not open the door.90 sec
121 60 sec
30 sec
ᤳ
WIPER SETUP
(P. 123)WIPER ACTION Changes the wiper operation between two settings
when the wiper switch is in the INT position.INTERMITTENT 123
WITH VEH SPD
ᤳ
DEFAULT ALL
(P. 93)Set/Cancel all the customized settings as default. SET 93
CANCEL
ᤳ: Default setting
Multi-Information Display92

DEFAULT ALLIf you want to set the default settings,
press the INFO (
/
) button to
select DEFAULT ALL, then press the
SEL/RESET button.
To set the default settings, press the
INFO (
/
) button to select SET
then press the SEL/RESET button.
If you want to cancel DEFAULT ALL,
select CANCEL, then press the SEL/
RESET button. The screen goes back
to the previous display.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
CUSTOMIZE ENTRY.
If the setting is not successfully
completed,‘‘FAILED’’is shown for
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
CONTINUED
Multi-Information Display
93
Instruments and Controls

Customize Settings
You can customize some of the
vehicle control settings to your
preference. Here are the settings you
can customize:●
ADAPTIVE CRUISE CONTROL
SETUP
●
METER SETUP
●
POSITION SETUP
●
LIGHTING SETUP
●
DOOR/WINDOW SETUP
●
WIPER SETUP
When you want to change the
vehicle control settings, press the
INFO (
/
) button to select CHG
SETTING, then press the SEL/
RESET button.Each time you press the INFO (
/
) button, the screen changes as
shown on the next page. Press the
INFO (
/
) button, until you see
the setup you want to customize,
then press the SEL/RESET button to
enter your selection.
Multi-Information Display94

SEL/RESET BUTTON
INFO (▲/▼) BUTTONMETER SETUP
see page 99
POSITION SETUP
see page 107
LIGHTING SETUP
see page 110 Select‘‘EXIT’’
Select‘‘CANCEL’’
DOOR/WINDOW
SETUP
see page 115
WIPER SETUP
see page 123 Select
‘‘DEFAULT ALL’’ADAPTIVE CRUISE
CONTROL SETUP
see page 96
CONTINUED
Multi-Information Display
95
Instruments and Controls

Adaptive Cruise Control SetupIf equippedThere are two custom settings for
adaptive cruise control (ACC):●
PRE-RUNNING CAR DETECT
BEEP
●
ACC DISPLAY SPEED UNIT
To enter customize mode, press the
SEL/RESET button while‘‘ACC
SETUP’’is displayed.
Each time you press the INFO (
/
) button, the screen changes as
shown in the illustration. Press the
INFO (
/
) button until you see the
setting you want to customize, then
press the SEL/RESET button to
enter your selection.
SEL/RESET
BUTTON
INFO (▲/▼)
BUTTON
Multi-Information Display96

Pre-Running Car Detect BeepWhen PRE-RUNNING CAR
DETECT BEEP is set to ON, one
beep sounds when the ACC detects a
vehicle in front of you. A beep also
sounds when that vehicle passes out
of the range of your vehicle's radar
sensor.
Select this item from‘‘ACC SETUP’’
by pressing the INFO (
/
) button
repeatedly until‘‘PRE-RUNNING
CAR DETECT BEEP’’is displayed.
Press the SEL/RESET button to
display the selections. Select ON or
OFF by pressing the INFO (
/
)
button, then press the SEL/RESET
button to enter your selection.
When your selection is successfully
completed, the display changes as
shown above, and then returns to the
customize item screen.
If the‘‘SETTING INCOMPLETE’’
message appears, return to‘‘PRE-
RUNNING CAR DETECT BEEP’’
and repeat the procedure again.
CONTINUED
Multi-Information Display
97
Instruments and Controls