2012.5 Peugeot RCZ Owner's Manual - RHD (UK, Australia)

8/
PRACTICAL INFORMATION







Changing dipped beam headlamp bulbs



)
Remove the protective cover by pulling the tab.

)
Disconnect the bulb connector.

)
Spread the springs to release the bulb.

)
Pull the bulb out and change it.
To refi t, carry out these operations in reverse order.

















Changing main beam headlamp bulbs



)
Remove the protective cover by pulling on the tab.

)
Disconnect the bulb connector.

)
Compress the springs to release the bulb.

)
Remove the bulb and change it
To refi t, carry out these operations in reverse order.


Changing daytime running lamp / sidelamp bulbs



)
Remove the protective cover by pulling on the tab.

)
Disconnect the bulb connector.

)
Turn the bulb holder a quarter of a turn and extract it.

)
Pull the bulb and change it.
To refi t, carry out these operations in reverse order.

176

Changing integrated direction indicator side repeaters


Changing the daytime running lamps / sidelamps
































REAR LAMPS



1.
Sidelamps (LEDs).


2.
Direction indicators (LEDs).


3.
Brake lamps / sidelamps (P21/5W).


4.
Reversing lamps (P21W).


5.
Foglamp (P21W).


For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop. For the replacement of these bulbs, contact a PEUGEOT dealer or a
qualifi ed workshop.

8/
PRACTICAL INFORMATION

Changing brake lamps / sidelamps

This bulb is changed from outside the boot, having fi rst removed the
rear lamp:


)
open the boot lid,

)
unclip the access fl ap of the corresponding side trim, then remove it,

)
unclip the lamp taking hold of it at the base, then tilt it,

)
turn the bulb holder one quarter of a turn and remove it,

)
turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.
)
disconnect the lamp connector,

)
remove the two lamp fi xing bolts,

178

Changing reversing lamps and foglamps

These two bulbs are changed from outside the rear bumper:


)
unclip the protective cover from the rear, then tilt it,

)
remove it completely to gain access to the two lamp fi xing bolts,

On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.


)
turn these two bolts one quarter of a turn and remove them,

)
push the lamp towards the inside to unclip it, then tilt it,

)
pull the lamp towards the outside for access to the various
bulb-holders.


- For the reversing lamps: pull the corresponding bulb holder,

- turn the bulb one quarter of a turn and change it.


- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,

- turn the bulb one quarter of a turn and change it.

To refi t, carry out these operations in reverse order.

8/
PRACTICAL INFORMATION

Changing sidelamps and direction indicators

For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.

High pressure washing

When using this type of washing on stubborn dirt, do not persist
on the headlamps, the lamps and their surrounds to avoid
damaging their protective coating and seals.


Changing number plate lamps (W5W)



)
Insert the end of the vehicle's key in the hole in the transparent
cover.

)
Push towards the outside to unclip it.

)
Remove the transparent cover.

)
Pull the bulb out and change it.



Changing the third brake lamp (LEDs)

For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.

180
CHANGING A FUSE

ACCESS TO TOOLS

The extraction tweezer is fi tted to the back of the dashboard fusebox
cover. For access to it:


)
open the glove box lid,

)
push the opening guide to the left to pass the fi rst notch,

)
open the glove box lid fully,

)
turn the screw a quarter of a turn to the left,

)
unclip the fusebox cover by pulling at the top right,

)
disconnect the cover completely and turn it over,

)
extract the carrier on the back of which fi tted the tweezer.

8/
PRACTICAL INFORMATION

CHANGING A FUSE

Before changing a fuse, it is necessary to:


)
identify and rectify the cause of the failure,

)
switch off all electrical consumers,

)
immobilise the vehicle and switch off the ignition,

)
identify the failed fuse using the tables and diagrams in the
following pages.
When working on a fuse, it is important to:


)
use the special tweezer to extract the fuse from its housing.

)
always replace the failed fuse with a fuse of the same rating
(same colour); the use of a fuse of a different rating may cause a
malfunction (risk of fi re).

Good

Failed


Tweezer
If the fault recurs soon after changing a fuse, have the electrical
system of your vehicle checked by a PEUGEOT dealer or a
qualifi ed workshop.


Installing electrical accessories

Your vehicle's electrical system is designed to operate with
standard or optional equipment.
Before installing other electrical equipment or accessories on your
vehicle, contact a PEUGEOT dealer or a qualifi ed workshop.
PEUGEOT will not accept responsibility for the cost incurred in
repairing your vehicle or for rectifying malfunctions resulting from
the installation of accessories not supplied and not recommended
by PEUGEOT and not installed in accordance with its instructions,
in particular when the combined consumption of all of the
additional equipment connected exceeds 10 milliamperes.

182

DASHBOARD FUSES

The fusebox is placed in the lower part of the dashboard (left hand side,
inside the glove box). It consists of two boxes.

Access to the fuses



)
refer to the paragraph "Access to tools".



Fuse tables



Fuse N°



Rating


Functions



F1



-

Not used.


F2



30 A

Locking and deadlocking earth.


F3



5 A

Airbags, active bonnet and pretensioners
control unit.


F4



10 A

Clutch pedal switch, electrochrome
rear view mirror, automatic gearbox,
switching and protection unit.


F5



30 A

One-touch electric windows, folding
mirrors supply.


F6



-

Not used.


F7



5 A

Front and rear courtesy lamps, map
reading lamps, sun visor lighting, glove
box lighting.


F8



20 A

Audio equipment, audio/telephone,
multifunction screen, tyre under-infl ation
detection, clock.


F9



30 A

12 V socket.


F10



15 A

Steering mounted controls.


F11



15 A

Low current ignition switch.


F12



15 A

Instrument panel, air conditioning,
driver's seat memory unit, rain /
sunshine sensor, airbags.

Box 1