2012.5 Citroen C3 PICASSO RHD tow

Driving
140
Deactivation
Reactivation
With the engine running, press button Ato deactivate the system permanently. The indicator lamp in the button comes on.
The system will be deactivated automatically when towing a trailer or when a bicycle carrier is fitted (vehiclefitted with a towbar or bicycle carrier recommended by CITROËN).
In bad or wintry weather, ensure thatthe sensors are not covered with mud,frost or snow.
Press button A again to reactivate the system. The indicator lamp in the button goes off.
If there is an operating fault, when reverse gear
is engaged, the ser vice warning lamp comes
on, accompanied by an audible signal (shortbeep) and a message in the multifunction screen.

Checks
150

If excessive travel or a loss of effectiveness of this system is
noticed, the parking brake must be checked, even between two ser vices.
Manual gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the ser vicing booklet for the
details of the level checking inter val for this component.
For in
formation on checking brake
disc wear, contact a CITROËN dealer
or a qualified workshop.


Brake disc wear
Brake wear depends on the style
of driving, par ticularly in the case
of vehicles used in town, over shor t
distances. It may be necessary to have
the condition o
f the brakes checked, even between vehicle services.















Brake pads

The gearbox does not require anymaintenance (no oil change).
Refer to the servicing booklet for
details of the checking inter val for
this component.
Electronic gearbox














Only use products recommended by CITROËN or products of equivalent quality and specification.
In order to optimise the operationof units as impor tant as the braking system, CITROËN selects and offersvery specific products. Checkin
g this system must be done by a CITROËN dealer or a qualified workshop.
Unless there is a leak in the circuit, a drop in
the brake fluid level indicates that the brake pads are worn.

Practical information
154
2. Infl ation
)Turn the selector Ato the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
) Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave the engine running.

)Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that thepuncture has not been fully plugged; contact a CITROËN dealer or qualified
workshop for assistance.)Remove and stow the kit.)Drive at reduced speed (50 mph
[80 km/h] max) limiting the distance
travelled to approximately 120 miles (200 km).

As soon as possible, go to a CITROËNdealer or a qualified workshop.You must inform the technician that you have used this kit. After inspection, the technician will advise you on whether
the tyre can be repaired or if it must be replaced.

11
Practical information
155

Removing the cartridge
)Stow the black pipe. )Detach the angled base from the white pipe.)Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.
Checking tyre pressures /
inflating accessories
You can also use the compressor, without
injecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).

)
Turn the selector Ato the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
) Connect the compressor's electrical connector to the vehicle's 12 V socket. )
Star t the vehicle and let the engine run. )
Adjust the pressure using the compressor (to inflate: switch B
in position "I" ; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. ) Remove the kit then stow it.




Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for single use; even if only partly used, itmust be replaced. After use, do not discard the car tridgeinto the environment, take it to an authorised waste disposal site or a CITROËN dealer.

Do not forget to obtain a new sealantcartridge, available from CITROËN dealers or from a qualified workshop.

Practical information
156














Changing a wheel
The tools are installed under the boot floor.
For access to them:)open the boot, )remove the boot floor, )lift up the boot carpet, )remove the box containing the tools, )remove the polystyrene storage box.

Other accessories
5.
Removable towing eye.
Refer to the paragraph "Towing the vehicle".
Access to the tools
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.


List of tools

All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts. 2. Jack with integral handle.
For raising the vehicle. 3. "Bolt cover" tool.
For removing the bolt protectors (covers)on alloy wheels. 4.Socket for the security bolts (located in theglove box).
For adapting the wheelbrace to the special "security" bolts (if your vehicle has them).

Practical information
158
Taking out the wheel
)Unscrew the yellow central bolt, andremove it.)Raise the spare wheel towards you from
the rear.)Take the wheel out of the boot.
Putting the wheel back in place
)
Put the wheel back in its housing. )
Refit the yellow central bolt in the centre of
the wheel. ) Tighten fully until the central bolt clicks to
retain the wheel correctly.
)Put the polystyrene storage box back inplace. )Put the box back in place and clip it.

11
Practical information
163











Changing a bulb
Procedure for replacing a faulty bulb with a new bulb.
1
.Direction indicators (H21W amber).2.Dipped beam headlamps (H7-55W).3. Main beam headlamps (H1- 55W).4.Sidelamps (W5W).5.Foglamps (PSX24W).6.LED daytime running lamps.

Front lamps
The headlamps are fitted with polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water or apH neutral product,)
when using a high pressure washer on persistent marks, do not keep the lance directed towards thelamps or their edges for too long, so as not to damage their protectivecoating and seals,)
do not touch the bulb directly withyour fingers, use lint-free cloths.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of seriousburns). It is imperative to use only anti-ultraviolet(UV) type bulbs in order not to damage the headlamp.
Always replace a failed bulb with a new bulb with the same type andspecification.

Practical information
166
Changing front foglamp bulbs
)Remove the grille located under thefoglamp.

If you experience any difficulty in replacing bulbs, contact your CITROËN dealer or a qualified workshop.

)
Through the cover, remove the lampfinisher by pulling it towards you. )Unscrew the two fixing screws of the module and remove it from its housing.)Disconnect the bulb holder connector. )Remove the bulb and change it.
To r e
fit, carry out these operations in reverse order.