Page 12 of 80
DESCRIPTION
2-1
2
EAU10410
Left view1. Idle adjusting screw (page 6-12)
2. Battery (page 6-25)
3. Main fuse (page 6-27)
4. Fuse box (page 6-27)
5. Storage compartment (page 3-11)
6. Grab bar
7. Seat lock (page 3-10)
8. Shift pedal (page 3-6)9. Engine oil drain bolt (page 6-9)U5D1E1E0.book Page 1 Friday, September 5, 2008 1:17 PM
Page 42 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-9
6
EAU37804
Engine oil and oil filter ele-
ment The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the General periodic maintenance
and lubrication chart.
To check the engine oil level
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil set-
tles, and then check the oil level
through the check window located
at the bottom-right side of the
crankcase.TIPThe engine oil should be between theminimum and maximum level marks.4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
To change the engine oil (with or
without oil filter element replace-
ment)
1. Place the vehicle on a level sur-
face.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Place an oil pan under the engine
to collect the used oil.4. Remove the engine oil filler bolt
and drain bolt to drain the oil from
the crankcase.
TIPCheck the washer for damage and re-place it if necessary.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
1. Dipstick
1. Engine oil drain bolt
U5D1E1E0.book Page 9 Friday, September 5, 2008 1:17 PM
Page 43 of 80
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6 5. Remove the oil filter element drain
bolt to drain the oil from the oil filter
element.
TIPSkip steps 6–8 if the oil filter element isnot being replaced.
6. Remove the oil filter element cover
by removing the bolts.7. Remove and replace the oil filter
element and O-rings.
TIPMake sure that the O-rings are properlyseated.
8. Install the oil filter element cover by
installing the bolts, then tightening
them to the specified torque.
9. Install the engine oil drain bolt, and
then tighten it to the specified
torque.10. Install the oil filter element drain
bolt, and then tighten it to the spec-
ified torque.
11. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
bolt.
TIPBe sure to wipe off spilled oil on any
parts after the engine and exhaust sys-tem have cooled down.
1. Oil filter element cover bolt
2. Oil filter element drain bolt
1. Oil filter element
2. O-ring
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.4 ft·lbf)
Tightening torques:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 15 ft·lbf)
Oil filter element drain bolt:
7 Nm (0.7 m·kgf, 5.25 ft·lbf)
Recommended oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
1.35 L (1.43 US qt, 1.19 Imp.qt)
With oil filter element replacement:
1.45 L (1.53 US qt, 1.28 Imp.qt)
U5D1E1E0.book Page 10 Friday, September 5, 2008 1:17 PM
