2011 YAMAHA YBR250 wheel torque

PERIODIC MAINTENANCE AND ADJUSTMENT
6-20
6 4. If the drive chain slack is incorrect,
adjust it as follows.
EAU22822
To adjust the drive chain slack
1. Loosen the brake pedal free play
adjusting nut, axle nut, and locknut
at each end of the swingarm.2. To tighten the drive chain, turn the
drive chain slack adjusting nut at
each end of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting nut at each end
of the swingarm in direction (b),
and then push the rear wheel for-
ward. NOTICE: Improper drive
chain slack will overload the en-
gine as well as other vital parts
of the motorcycle and can lead
to chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
in the specified limits.
[ECA10571]
TIPUsing the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same po-sition for proper wheel alignment.
3. Tighten both locknuts and the axle
nut to the specified torques.
4. Adjust the brake pedal free play.
(See page 6-16.)
WARNING
EWA10660
After adjusting the brake pedal free
play, check the operation of thebrake light.
1. Drive chain slack
1
1. Axle nut
2. Drive chain slack adjusting nut
3. Locknut
4. Alignment marks
Tightening torques:
Locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle nut:
104 Nm (10.4 m·kgf, 77 ft·lbf)
U5D1E1E0.book Page 20 Friday, September 5, 2008 1:17 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
64. Remove the axle nut, pull the
wheel axle out, and then remove
the wheel. NOTICE: Do not apply
the brake after the wheel has
been removed together with the
brake disc, otherwise the brake
pads will be forced shut.
[ECA11071]
EAUW0160
To install the front wheel
1. Lift the wheel up between the fork
legs.TIPMake sure that there is enough space
between the brake pads before insert-ing the brake disc into the caliper.
2. Insert the wheel axle.
3. Lower the front wheel so that it is
on the ground.
4. Tighten the wheel axle to the spec-
ified torque.
5. Tighten the front fork pinch bolt to
the specified torque.6. Push down hard on the handlebar
several times to check for proper
fork operation.
EAU25080
Rear wheel
EAU25431
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of itfalling over.
1. Loosen the axle nut and the brake
torque rod nut at the brake shoe
plate.
Tightening torque:
Wheel axle:
60 Nm (6.0 m·kgf, 44 ft·lbf)
Tightening torque:
Front fork pinch bolt:
55 Nm (5.5 m·kgf, 40 ft·lbf)
1. Drive chain slack adjusting nut
2. Brake torque rod
3. Locknut
4. Brake pedal free play adjusting nut
5. Axle nut
U5D1E1E0.book Page 31 Friday, September 5, 2008 1:17 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
6 2. Lift the rear wheel off the ground
according to the procedure on
page 6-30.
3. Disconnect the brake torque rod
from the brake shoe plate by re-
moving the nut and the bolt.
4. Remove the brake pedal free play
adjusting nut, and then disconnect
the brake rod at the brake cam-
shaft lever.
5. Loosen the locknut and the drive
chain adjusting nut on both ends of
the swingarm.
6. Remove the axle nut, and then pull
the wheel axle out.
7. Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
TIPThe drive chain does not need to be
disassembled in order to remove andinstall the wheel.
8. Remove the wheel.
EAUW0170
To install the rear wheel
1. Insert the wheel axle from the left-
hand side, and then install the
drive chain onto the rear sprocket.
2. Install the axle nut.
3. Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting
nut.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then tight-
en the nut to the specified torque.5. Adjust the drive chain slack. (See
page 6-19.)
6. Lower the rear wheel so that it is
on the ground.
7. Tighten the axle nut to the speci-
fied torque.
8. Adjust the brake pedal position
and free play. (See page 6-16.)
WARNING
EWA10660
After adjusting the brake pedal free
play, check the operation of thebrake light.
Tightening torque:
Brake torque rod nut:
49 Nm (4.9 m·kgf, 36 ft·lbf)
Tightening torque:
Axle nut:
104 Nm (10.4 m·kgf, 77 ft·lbf)
U5D1E1E0.book Page 32 Friday, September 5, 2008 1:17 PM