2011 SKODA FABIA wheel

The turn signal
  and main beam lever The parking lights and headlight flasher are also switched on and
off using the turn signal and main beam lever.
Fig. 26 Turn signal and main beam lever
The turn signal and main beam lever perform the following functions:
Right  and left  turn signal light
– Push the lever upwards A or downwards
B ⇒
 fig. 26 .
– If you only wish to flash three times (the so-called convenience turn signal),
push the lever briefly up to the upper or lower pressure point and release it.
– Turn signal for changing lanes - in order to only flash briefly, move the lever up
or down to the pressure point and hold it in this position.
Main beam 
– Switch on the low beam.
– Push the lever forwards in direction of arrow C .
– If you push the lever into the initial position in the direction of arrow D the
main beam is switched off.
Headlight flasher 
– Pull the lever towards the steering wheel (spring-tensioned position) - the
main beam and warning light  in the instrument cluster come on.
Parking light 
– Switch off the ignition.
– Push the lever up or down - the right-hand or left-hand parking light is switch-
ed on. Information concerning the function of the lights.
●
The turn signal system only operates when the ignition is switched on. The
corresponding warning light  or  in the instrument cluster also flashes.
● The turn signal is automatically cancelled after negotiating a curve.
● The side light and rear light on the appropriate side of the vehicle are switched
on when the parking light is selected. The parking light function only operates if
the ignition is switched off.
● An acoustic warning signal will sound when the driver's door is opened if the
lever is not in the middle position after removing the ignition key from the ignition
lock. The acoustic warning signal will stop just as soon as the driver's door is
closed. CAUTION
Use main beam or the headlight flasher only if this does not risk dazzling other
road users. Note
● If you have switched on the right or left turn signal light and you switch off the
ignition, the parking light is not automatically switched on.
● Use only in accordance with the legal requirements the described lighting and
signal systems. 
Interior lighting Interior vehicle lighting - version 1 Fig. 27 Interior lighting - version 1
£ 45
Lights and Visibility Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Windshield wiper and wash system
Windshield wiper You can operate the windscreen wipers and automatic wipe/wash
using the windscreen wiper lever.
Fig. 32 Windscreen wiper lever
The windscreen wiper lever ⇒ 
fig. 32 has the following positions:
Finger-operated wiping
– If you wish to wipe the windscreen only briefly, push the lever into the sprung
position 4 .
Intermittent wiping
– Position the lever up into position 1 .
– Set with the switch A the desired break between the individual wiper
strokes.
Slow wipe
– Position the lever up into position 2 .
Fast wipe
– Position the lever up into position 3 .
Automatic wipe/wash for windscreen
– Pull the lever towards the steering wheel into the spring-tensioned position
5 , the wash system and the windscreen wipers will operate. –
Release the lever. The windscreen wash system stops and the wiper contin-
ues for another 1 - 3 wiper strokes (depending on the period of spraying of the
windscreen).
Wiping the rear window pane
– Push the lever away from the steering wheel into position 6 ⇒ fig. 32, the
widescreen wiper will operate every 6 seconds.
Automatic wipe/wash for the rear window pane
– Push the lever away from the steering wheel into the spring-tensioned posi-
tion 7 , the windscreen wiper and wash system will operate.
– Letting go of the lever will cause the windscreen wash system to stop and the
windscreen wiper to continue for another 1 - 3 wiper strokes (depending on
the period of spraying of the windscreen). The lever will stay in position after
releasing it 6 .
Switching windscreen wipers off
– Move the lever back into its home position 0 .
The windscreen wipers and the windscreen washer system only operate if the ig-
nition is switched on.
The rear window will be wiped again if the window wipers are on when reverse
gear is selected.
The windscreen washer nozzles for the windscreen are heated when the ignition
is switched on.
Top up with wash liquid ⇒ page

163. WARNING
● Properly maintained windscreen wiper blades are essential for clear visibil-
ity and safe driving ⇒ 

page 49.
● Do not use the windscreen washer system at low temperatures, without
heating the windscreen beforehand. Otherwise the window cleaner could
freeze on the windscreen and restrict the view to the front.
● In the event of a freezing up of the windscreen, first of all remove the ice
⇒ 

page 146 and then operate the windscreen wiper otherwise the wind-
screen wiper blades could be damaged. £48
Lights and Visibility

Seats and Stowage
Front seats
Basic information The front seats have a wide range of different settings and can thus be matched
to the physical characteristics of the driver and front passenger.
Correct adjustment of the seats is particularly important for:
●
safely and quickly reaching the controls;
● a relaxed, fatigue-free body position;
● achieving the maximum protection offered by the seat belts and the airbag
system.
The chapters which follow describe the procedure which you should adopt for ad-
justing the seats. WARNING
● Never transport more occupants than the maximum seating in the vehicle.
● Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened ⇒ 
page 121, Transporting children safely with a
suitable restraint system.
● The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be
correctly fastened in order to provide an optimal protection for you and your
occupants.
● Always keep your feet in the footwell when the car is being driven - never
place your feet on the instrument panel, out of the window or on the surfaces
of the seats. This is particularly important for the front seat passenger. You
will be exposed to increased risk of injury if it becomes necessary to apply the
brake or in the event of an accident. If an airbag is deployed, you may suffer
fatal injuries when adopting an incorrect seated position! WARNING (Continued)
● It is important for the driver and front passenger to maintain a distance of
at least 25 cm from the steering wheel or dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to proper-
ly protect you - hazard! The front seats and the head restraints must always
also be correctly adjusted to match the body size of the occupant.
● Ensure that there are no objects in the footwell as any objects may get be-
hind the pedals during a driving or braking manoeuvre. You would then no
longer be able to operate the clutch, to brake or accelerate.
● Do not transport any objects on the front passenger seat except objects
(e.g. child safety seat) provided for this purpose - risk of accident! 
Adjusting the front seats - Variant 1 Fig. 37 Controls at seat
Adjusting a seat in a forward/back direction
– Pull the lever 1 ⇒
 fig. 37
up and push the seat into the desired position.
– Release the lever 1 and push the seat further until the lock is heard to en-
gage.
Adjusting height of seat
– Lift the seat if required by pulling or pumping lever 2 upwards.
– Lower the seat if required by pushing or pumping lever 2 downwards.
£52
Seats and Stowage

Adjust the angle of the seat backrest
–
Relieve any pressure on the seat backrest (do not lean on it) and turn the
handwheel 3 to adjust the angle of the backrest.
The driver's seat should be adjusted in such a way that the pedals can be fully
pressed to the floor with slightly bent legs.
The seat backrest on the driver's seat should be adjusted in such a way that the
upper point of the steering wheel can be easily reached with slightly bent arms. WARNING
● Only adjust the driver seat when the vehicle is stationary - risk of injury!
● Take care when adjusting the seat! Adjusting the seat without care can
lead to bruises or injuries.
● The seat backrests must not be angled too far back when driving other-
wise this will affect proper operation of the seat belts and of the airbag sys-
tem - risk of injury! 
Adjusting the front seats - Variant 2 Fig. 38 Controls at seat
This front seat variant is only available in some countries.
Adjusting a seat in a forward/back direction
– Pull the lever (in the middle section) 1 ⇒ fig. 38
up and push the seat into the
desired position.
– Release the lever 1 and push the seat further until the lock is heard to en-
gage. Adjusting height of seat
–
Lift the seat if required by pulling or pumping lever 2 upwards.
– Lower the seat if required by pushing or pumping lever 2 downwards.
Adjust the angle of the seat backrest
– Remove the pressure of the backrest (do not lean on it), pull the lever 3 to-
wards the rear and set the desired angle of the seat backrest with the back
– After releasing the lever 3 , the seat backrest will remain in the set position.
The driver's seat should be adjusted in such a way that the pedals can be fully
pressed to the floor with slightly bent legs.
The seat backrest on the driver's seat should be adjusted in such a way that the
upper point of the steering wheel can be easily reached with slightly bent arms. WARNING
● Only adjust the driver seat when the vehicle is stationary - risk of injury!
● Take care when adjusting the seat! Adjusting the seat without care can
lead to bruises or injuries.
● The seat backrests must not be angled too far back when driving other-
wise this will affect proper operation of the seat belts and of the airbag sys-
tem - risk of injury! 
Head restraints Fig. 39 Head restraint: Adjusting/pulling out
Best protection is achieved if the top edge of the head restraint is at the same
level as the upper part of your head.
£ 53
Seats and Stowage Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Install bicycle carrier
Fig. 57 Install bicycle carrier
– Position the approved bicycle carrier on the cross member, after pulling up the
screw A ⇒ fig. 57 push the frame side rail (alu-part) towards the cross mem-
ber until the socket latches, and screw the screw A into the nut.
– Slacken the screw B and take it out of the moveable part of the fixture; posi-
tion the moveable part of the carrier, depending on bicycle size, into one of the
possible positions, so that it does not come in contact with the boot lid. We
recommend to place the moveable part of the fixture in such a position that
the holes are visible between the screw A and the moveable part.
– Insert the screw B into the desired position and tighten.

Put bicycle into the bicycle carrier Fig. 58 Put in the bicycle/fastening the front wheel
–
Remove the front wheel before putting the bicycle into the vehicle. –
Slacken the quick tension jack on the fixing axle of the bicycle carrier and ad-
just according to the width of the bicycle fork.
– Fit the bicycle fork onto the fixing axle and tighten with the quick tension jack
⇒ fig. 58 - left.
– Position the left pedal of the bicycle forward, in order to attach the front
wheel more easily.
– Slacken the screw A ⇒ fig. 57 and push the bicycle holder together with the
attached bicycle to the left (in the direction of the arrow), so that no collision
between the steering arm and the side window of the luggage compartment
can occur.
– Carefully guide the boot lid to the bottom without letting it go and at the same
time check if there is adequate room between the steering arm of the bicycle
and the window of the boot lid. If necessary adapt the position of the movea-
ble part of the bicycle carrier in such a way that no collision can occur
⇒ page 64 .
– It is best to push the removed front wheel between the crank of the left pedal
and the bicycle frame, attach it with a strap to the front fork ⇒ fig. 58
- right,
and/or to a fixing point.
– Make sure that it does not lead to damage of the trim panel of the luggage
compartment, the bicycle and the placed objects.
– Perform the installation of the second fixture and the attachment of the bicy-
cle analogously. WARNING
Place the bicycles in the bicycle carrier in such a position that no collision be-
tween the steering arm and the side and/or rear window can occur. Note
If the front wheel is equipped with disc brake, attach the wheel in such a way that
the brake disc is opposite the frame. 64
Seats and Stowage

Storage compartment on the driver's side
Fig. 69 Dash panel: Storage compart-
ment on the driver's side
Unlockable compartment below the steering wheel on the left. 
Stowage compartment for spectacles Fig. 70 Detail of the headliner: Stowage
compartment for spectacles
– Press on the lid of the storage compartment, the storage compartment opens
downwards ⇒ fig. 70. CAUTION
● The compartment must only be opened when removing or inserting the spec-
tacles and otherwise must be kept closed.
● Do not put any heat-sensitive objects in the stowage compartment - they may
be damaged. Stowage compartment in centre console
Fig. 71 Centre console: Storage com-
partment
Unlocable compartment in the centre console. 
Storage compartment in the front seat Fig. 72 Front seat: Storage compart-
ment
– Tilt the lock to open the flap and pull out the flap ⇒ fig. 72.
– Tilt the lock to close the flap and press flap close. CAUTION
The storage compartment is designed for storing small objects of up to 1 kg. in
weight. 70
Seats and Stowage

Air outlet vents
The information provided is valid for all vehicles.
Fig. 77 Air outlet vents
Open the air outlet vents 3 and 4
–
Turn the vertical thumbwheel (air outlet vents 3) or the horizontal wheel (air
outlet vents 4) to the position .
Close air outlet vents 3 and 4
– Turn the vertical thumbwheel (air outlet vents 3) or the horizontal wheel (air
outlet vents 4) to the position 0.
Change air flow of air outlet vents 3 and 4
– In order to change the strength of the air flow, swivel the horizontal lamellas
with the aid of the moveable adjuster.
– In order to change the lateral direction of the air flow, turn the vertical lamel-
las with the aid of the moveable adjuster.
You can set the air supply to the individual vents with the air distribution control C ⇒ fig. 78. Air outlet vents
3 and 4 can also be opened or closed individually.
Warmed, unwarmed or cooled air will flow out of the air outlet vents according to
the setting of the regulator of the heating or the air conditioning system and the
atmospheric conditions. Heating
Using the system The heating system delivers air into the interior of the vehicle and
warms it as required.
Fig. 78 Heating: Control elements
Setting temperature
– Turn the control dial A ⇒
 fig. 78 to the right in order to increase the tempera-
ture.
– Turn the control dial A to the left in order to increase the temperature.
Controlling blower
– Turn the blower switch B into one of the positions, 1 to 4, in order to switch
the blower on.
– Turn the blower switch B into position 0 in order to switch the blower off.
– If you wish to shut off the fresh air supply, use the button 1 - recirculated air
mode ⇒ page 75.
Control for air distribution
– You can adjust the direction of the inlet air flow ⇒ page 74
using air distribu-
tion regulator C .
Rear window heater
– Press button 2 . Further information
⇒ page 47, Rear window heater.
All controls apart from the control dial B can be set to any desired intermediate
position. £74
Heating and air conditioning system

Starting-off and Driving
Setting steering wheel position Fig. 81 Adjustable steering wheel: Lever below the steering column/Safe distance to steering
wheel
You can set the height and the forward/back position of the steering wheel to the
desired position.
–
Adjust the driver seat ⇒ page 52.
– Pull the lever below the steering wheel down ⇒ fig. 81 - left ⇒  .
– Set the steering wheel to the desired position (concerning height and forward/
back position).
– Then push the lever up against the steering column until it locks into place. WARNING
● You must not adjust the steering wheel when the vehicle is moving!
● The driver must maintain a distance of at least 25 cm to the steering wheel
⇒ fig. 81 - right. Not maintaining this minimum distance will mean that the air-
bag system will not be able to properly protect you - hazard!
● For safety reasons the lever must always be firmly pushed up to avoid the
steering wheel altering its position unintentionally when driving - risk of acci-
dent! WARNING (Continued)
● If you adjust the steering wheel further towards the head, you will reduce
the protection offered by the driver airbag in the event of an accident. Check
that the steering wheel is aligned to the chest.
● When driving, hold the steering wheel with both hands firmly on the outer
edge in the 9 o'clock and 3 o'clock position. Never hold the steering wheel
firmly in the 12 o'clock position or in another way (e.g. in the middle of the
steering wheel or at the inner steering wheel edge). In such cases, injuries to
the arms, the hands and the head can occur when the driver airbag is de-
ployed. 
Ignition lock Fig. 82 Ignition lock positions
Petrol engines 1 - ignition switched off, engine off, the steering can be locked.
2 - ignition switched on
3 - start engine
Diesel engines 1 - interruption of fuel supply, ignition switched off, engine off, the steering can
be locked.
2 - heating glow plugs on, ignition switched on
● You should not switch on any major electrical components during the heating
period otherwise the vehicle battery will be drained unnecessarily. £82
Starting-off and Driving