2011 RENAULT SCENIC light

13B-68
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF089
PRESENTINLET MANIFOLD PRESSURE SENSOR CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: Inconsistency
6.DEF: At maximum limit
7.DEF: At minimum limit
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
The level 1 warning light illuminates along with the message Faulty injection.
K9K 722 ENGINE
1.DEF-2.DEF
3.DEF-4.DEF
NOTESNone.
Check the connection and condition of the 4-track connector of the inlet pressure sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 track C3 computer connector B
Sensor connector track 2 track J2 computer connector B
Sensor connector track 3 track C1 computer connector B
Sensor connector track 4 track C2 computer connector B
Repair if necessary.
DDCR_V44_DF089P/DDCR_V48_DF089P

13B-72
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF107
STOREDCOMPUTER MEMORY
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Special note:
If fault DF107, the engine stops and cannot be restarted and the level 1 warning light
illuminates along with the message Faulty injection.
Enter the individual injector corrections (C2I) using the diagnostic tool (command SC002).
If the fault is still present, contact the Techline.
DDCR_V44_DF107M/DDCR_V48_DF107M

13B-74
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF113
PRESENTSENSOR SUPPLY VOLTAGE1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESSpecial notes:
If DF113, the engine stops immediately and cannot be restarted. The level 1 warning
light illuminates along with the message Faulty injection.
Check the condition and connection of the connectors of all sensors with a 5 V feed.
– Refrigerant pressure sensor
– Pressure sensor and inlet manifold temperature sensor
– Rail pressure sensor
– Pedal sensor gang 1
– EGR valve position sensor
– Flow sensor.
Repair if necessary.
Check the condition and connection of computer connectors A, B, and C.
Repair if necessary.
To locate any internal fault in one of the sensors with a 5 V supply (short circuit), disconnect each of the sensors
on the list above in turn, checking after each disconnection whether the fault changes status from present to
stored.
If the faulty sensor is located, check its connections and that it is in order. If necessary replace the sensor.
Connect the bornier in place of the computer and check the insulation, continuity and the absence of
interference resistance on the following connections:
Computer connector C track C4 Track B refrigerant pressure sensor
Computer connector B track C1 Track 3 inlet pressure - temperature sensor
Computer connector B track D1 Track 3 rail pressure sensor
Computer connector A track G2 Track 3 pedal sensor gang 1
Computer connector B track B1 Track 2 EGR valve position sensor
Computer connector B track A1 Track 3 of the flowmeter
Repair if necessary.
If the fault is still present, apply the fault finding procedure for each sensor with a 5 V supply.
DDCR_V44_DF113P/DDCR_V48_DF113P

13B-75
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF114
STOREDEGR SOLENOID VALVE CIRCUIT
1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Inconsistency
4.DEF: Valve jammed
5.DEF: Valve clogged
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF114 is present: the engine is unstable and may even stall. Starting difficult or
even impossible when cold, smoke emissions and loss of performance possible. On
status 4.DEF, the level 1 warning light illuminates with the message Faulty injection
displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the EGR valve connector, component code 169.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +12 V on connection 3FB2 of component 169.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connections:
–3GB between components 169 and 120,
–3FB2 between components 169 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DDCR_V44_DF114M/DDCR_V48_DF114M

13B-79
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF122
PRESENTPEDAL POTENTIOMETER GANG 2 SUPPLY VOLTAGECO.1: Open circuit or short circuit to +12 volts
CC.0: Short circuit to earth
NOTESSpecial notes:
If DF122, the idling speed is stuck at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates along with the message Faulty
injection.
CC.0
NOTESNone.
Check the connection and condition of the 6-track connector of the pedal potentiometer.
Repair if necessary.
Check the connection and condition of the black 32-track connector A of the computer.
Repair if necessary.
Measure the resistance between tracks 2 and 6 of the pedal potentiometer.
Replace the pedal potentiometer if the resistance is not 2.85 kΩ +
2.05 Ω.
Disconnect computer connector A and the pedal potentiometer connector.
Check the insulation against earth of the connection on track F2 on computer connector A.
Repair if necessary.
DDCR_V44_DF122P/DDCR_V48_DF122P

13B-81
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF130
STOREDFLOW CAPACITY FUNCTION
NOTESSpecial notes:
If DF130, the engine may stop with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Check the connection and condition of the of the fuel flow actuator connector (IMV), and repair it if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω ± 0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connection:
Computer connector B track M4 track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
Run Test 6 High pressure system check.
Repair if necessary.
DDCR_V44_DF130M/DDCR_V48_DF130M

13B-142
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET704
ET705
CONTINUED
ACTIVE
OR
INACTIVE
If the brake lights are working:
check the continuity and the absence of interference resistance on the following
connection:
– connection code 5A between components 160 and 120, 645, 119.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
disconnect the switch and carry out the following checks:
for MEGANE II and SCENIC II with ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For MEGANE II and SCENIC II without ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
Replace the switch if the values obtained are not correct.