2011 RENAULT SCENIC cruise control

13B-128
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET042
CONTINUED 3
CRUISE
CONTROL
When the driver presses the main switch in the speed limiter position, status
ET042becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in
the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for +12 V after ignition feed on the main switch connector.
• Connection code AP43 of component 1546.
Disconnect the main switch, and when it is in the rest position, check the insulation
between:
• Connection codes AP43 and 3FX of component 1546.
• Connection codes AP43 and 3PD of component 1546.
– Check the continuity between connections AP43 and 3PD of component 1546
in the speed limiter position.
– Check the continuity between connections AP43 and 3FX of component 1546
in the cruise control position.
If these checks show incorrect values, replace the main switch.
Check the continuity, insulation and the absence of interference resistance on
the following connections:
• Connection code 3FX,
• Connection code 3PD,
Between components 1546 and 120.
Also check the engine management computer connectors.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.

13B-131
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415 CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESNone.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control / speed limiter function, due to a driver
request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 Fault memory, to reset this status to NONE.
NONEThis status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and traction control is
requested.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 1 without traction control requested (see 38C,
ABS).
DDCR_V44_ET415/DDCR_V48_ET415

13B-132
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 1
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the brake pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult
the interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, MULTIPLEXING).

13B-133
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 2
STATUS 4
Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active,
– and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control - speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.

13B-134
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 3
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without
the injection computer receiving a signal that the brake pedal switch has been
pressed.
If status ET415 is STATUS 5, consult the interpretation:
– of status ET042 Cruise control/Speed limiter,
– of status ET703 Cruise control - speed limiter buttons,
– of status ET704 Brake switch no. 1,
– and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and locate the faulty
component.
Also, check the operation of the accelerator pedal, and use the diagnostic tool to
check the presence of a fault connected with this component. Deal with them if
necessary.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with the present faults or those stored in
the injection computer.
If the fault is still present, contact the Techline.

13B-135
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 4
STATUS 6
Gear lever in neutral (manual gearbox) or the neutral position
(automatic gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of
the tyre size stored in the computer. If the configuration is correct, contact the
Techline.
STATUS 7Inconsistency between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference in
speed.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 7 on relatively flat terrain, contact the Techline.

13B-136
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 5
STATUS 8
Automatic transmission in defect mode.
NOT AVAILABLE ON THIS SOFTWARE
STATUS 9Vehicle speed monitoring
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the ABS computer.
Deal with the present or stored faults (see 38C, ABS).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If the specification STATUS 9 is still present, contact Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes STATUS 10 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and if the injection
computer detects a fault anywhere in the engine management system, or an engine
speed that is too high or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection
computer.
Deal with any present or stored faults (see 13B, Diesel injection).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 10 is still present, contact the Techline.

13B-137
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET703 CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system programming
functions.
INACTIVEStatus ET703 becomes INACTIVE when none of the cruise control - speed limiter
buttons are pressed. These buttons are located on the steering wheel.
To remove the driver's airbag to perform the checks in complete safety.
(see 88C, Airbag and pretensioners)
If status ET703 does not display INACTIVE,
• check the condition of the cruise control/speed limiter +/- button and the condition
of its connector.
• check the condition of the cruise control/speed limiter R/0 button and the condition
of its connector.
Repair if necessary.
DDCR_V44_ET703/DDCR_V48_ET703