2011 RENAULT SCENIC fuel

13B-176
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
*elec: electric
**circ: circuitET701
PARTICLE FILTER PRESSURE SENSOR
STATUS DEFINITIONACTIVE: This status indicates that the particle filter electric fuel pump is active.
INACTIVE: This status indicates that the particle filter electric fuel pump is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Only for vehicles equipped with a particle filter.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVE
INACTIVE
The status is ACTIVE during the particle filter regeneration phase.
If there is a fault, consult the interpretation of fault DF1004 Electric fuel pump control
relay circ**.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID304_V4D_ET701/SID304_V45_ET701/SID304_V49_ET701/SID301_V44_ET701/SID301_V4C_ET701
Siemens Injection
SID304
Vdiag No.: 44-45-49-4D-4C
Program No.: B2

13B-186
MR-372-J84-13B050$663.mif
V17
13B
DIESEL INJECTION
Fault finding – Parameter summary table
Tool parameter Diagnostic tool title
PR005EGR valve opening setpoint
PR008Rail reference pressure
PR009Turbocharging pressure setpoint
PR015Engine torque
PR017Fuel flow
PR028Pedal position (gang 1)
PR029Pedal position (gang 2)
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure
PR038Rail pressure
PR040Linearised rail pressure
PR041Turbocharging pressure
PR051EGR valve position feedback
PR055Engine speed
PR059Inlet air temperature
PR063Fuel temperature
PR064Coolant temperature
PR071Computer feed voltage
PR076Refrigerant sensor voltage
PR077EGR valve position sensor voltage
PR078Inlet pressure sensor voltage
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR082Fuel temperature sensor voltage
PR083Air temperature sensor voltage
PR084Coolant temperature sensor voltage
PR086Pedal potentiometer gang 1 voltage
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
MR-372-J84-13B050$663.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2

13B-187
MR-372-J84-13B050$663.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Parameter summary table13B
Tool parameter Diagnostic tool title
PR125Power absorbed by the AC* compressor Vdiag 44 and 48 only
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR171Air flow setpoint for EGR Vdiag 44 and 48 only
PR190Engine idle speed setpoint.
PR224Turbocharging pressure sensor voltage Vdiag 44 and 48 only
PR228Injector control capacitor voltage
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
Vdiag 4D, 45 and 49 only PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter
PR391Mileage since particle filter replacement
PR400New EGR valve offset
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
PR412Mileage at last successful regeneration
Vdiag 4D, 45 and 49 only PR414Particle filter diff* pressure
PR415Time since last regeneration
PR513Mileage counter for level 1 warning light
PR514Mileage counter for level 2 warning light
PR634Air flow request
PR667Turbine upstream temperature
Vdiag 4D, 45 and 49 only PR668Turbine upstream temperature sensor voltage
PR669Particle filter diff* press* sens* voltage
PR670Particle filter upstream temp* sens* voltage
PR671Particle filter downstream temp* sens* voltage
PR672Damper valve position setpoint Vdiag 44 and 48 only
*AC: air conditioning system
*diff: differential*sens: sensor
*temp: temperature*press: pressure

13B-188
MR-372-J84-13B050$663.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Parameter summary table13B
*St.: storedTool Parameter
Diagnostic tool title
PR739Fuel flow solenoid valve current
PR794Stored regeneration failure no. 1
Vdiag 4D, 45 and 49 only PR795Stored regeneration failure no. 2
PR796Stored regeneration failure no. 3
PR797Stored regeneration failure no. 4
PR798Stored regeneration failure no. 5
PR799Stored regeneration failure no. 6
PR800Stored regeneration failure no. 7
PR801Stored regeneration failure no. 8
PR802Stored regeneration failure no. 9
PR803Stored regeneration failure no.10
PR810Catalytic converter 1 downstream temperature
Vdiag 4D, 45 and 49 only
PR812Catalytic converter 1 temperature sensor
voltage
PR836St* particle filter warning light no. 1
Vdiag 45 and 49 only PR837St* particle filter warning light no. 2
PR838St* particle filter warning light no. 3
PR839St* particle filter warning light no. 4
PR840St* particle filter warning light no. 5
PR841St* particle filter warning light no. 6
PR842St* particle filter warning light no. 7
PR843St* particle filter warning light no. 8
PR844St* particle filter warning light no. 9
PR845St* particle filter warning light no. 10
PR873Oil oxidation signal Vdiag 44, 45, 48 and 49 only
PR874Last service
PR875Oil dilution signal Vdiag 44, 45, 48 and 49 only
PR878Increased idle speed Kangoo II only
PR879Maximum authorised speed Kangoo II only

13B-193
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR017
FUEL FLOW
PARAMETER
DEFINITIONThis parameter indicates the fuel flow in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running: 2.5 mg/st < PR017 < 8 mg/st.
In the event of a fault, refer to the interpretation of fault DF770 Flow regulator circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR017/SID304_V45_PR017/SID301_V48_PR017/SID304_V49_PR017/SID304_V4D_PR017/SID301_V4C_PR017

13B-200
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR038
RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the fuel pressure in the rail in bars.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after an inconsistency appears on the Parameter screen,
– following the activation of command AC003 Fuel pressure solenoid valve,
– following a customer complaint (starting problems, poor performance, stalling, etc.).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LX between components 1032 and 120,
–3LY between components 1032 and 120,
–3LZ between components 1032 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If all these connections are correct, check for the fuel pressure sensor supply:
+ 5 V on connection code 3LX between components 1032 and 120,
Earth on connection code 3LZ between components 1032 and 120.
If the connection(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the low and high pressure diesel circuit sealing (visual checks, odours): on pump body, pressure release
valve, pipes, rail and injector unions, injector wells, etc.
If all the above checks are correct:
With the vehicle ignition on, and engine stopped for over 1 minute:
Display PR038; if the value is lower than 30 bar, the sensor is correct.
Otherwise replace the rail pressure sensor (see MR 392, 385, 364, 370
and 417 Mechanical, 13B, Diesel
injection, Rail pressure sensor: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR038/SID304_V45_PR038/SID301_V48_PR038/SID304_V49_PR038/SID304_V4D_PR038/SID301_V4C_PR038

13B-205
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR059
INLET AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air inlet temperature in °C.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Check the condition of the air flowmeter connections, component code 799.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3ABQ and 3DW of component 799.
If the resistance is not:
(theoretical values)
3553 Ω < X < 3875 Ω at 10°C,
2353 Ω < R < 2543 Ω at 20°C,
1613 Ω < R < 1729 Ω at 30°C,
replace the air flowmeter (see MR 392, 385, 364, 370 and 417, Mechanical, 12A, Fuel mixture, Air flowmeter:
Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR059/SID304_V45_PR059/SID301_V48_PR059/SID304_V49_PR059/SID304_V4D_PR059/SID301_V4C_PR059

13B-206
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR063
FUEL TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the fuel temperature in °C.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
This parameter indicates the fuel temperature: - 30°C < PR063 < 90°C.
Default value: 60°C
In the event of a fault, consult the interpretation of fault DF098 Fuel temperature sensor circuit.
Sensor electrical conformity
Check for continuity and absence of interference resistance of the following connections:
– connection code 3FAB,
– connection code3LD,
between components 120 and 1066.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between connections3FAB and 3LD of component1066.
If its resistance is not:
1877 Ω < X < 2123 Ω at 25°C,
767 Ω < X < 861 Ω at 50°C,
301 Ω < X < 335 Ω at 80°C,
replace the fuel temperature sensor (see MR 392, 385, 364, 370 and 417, Mechanical, 13B, Diesel injection,
Fuel temperature sensor: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR063/SID304_V45_PR063/SID301_V48_PR063/SID304_V49_PR063/SID304_V4D_PR063/SID301_V4C_PR063