2011 RENAULT SCENIC coolant

13B-255
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR875
OIL DILUTION SIGNAL
PARAMETER
DEFINITIONThis parameter indicates the vehicle mileage when the oil dilution threshold is reached.
NOTESThis parameter should be interpreted only if the OCS (Oil Control System) program
is activated on the instrument panel. On the instrument panel computer, check the
configuration reading LC106 O.C.S: WITH.
Except Vdiag 44, 45 and 49.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80°C, without electrical consumers
The injection computer assesses the dilution rate of the engine oil according to the customer's driving style.
When the dilution level reaches a certain threshold before the end of the oil change interval, the injection
computer sends a signal to the instrument panel, which then displays Service required. Parameter PR875
corresponds to the vehicle mileage at the time this signal is sent.
IMPORTANT
When the message Service required appears on the instrument panel, the customer must arrange an immediate
oil change to prevent damage to the engine.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR875/SID304_V45_PR875/SID301_V4C_PR875

13B-256
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*CV: Commercial vehiclePR878
FAST IDLE SPEED
PARAMETER
DEFINITIONThis parameter indicates the value of the fast idle speed to use for the vehicle electrical
network in rpm.
NOTESThere must be no faults present. Perform fault finding after obtaining a parameter
inconsistency.
It is possible to modify the value of the PR878 using the command SC041
Modification of the commercial vehicle idle speed.
For Kangoo II only.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80°C, without electrical consumers
If the function has been activated ET800= ACTIVE and the fast idle speed value is 1000 or 1100 rpm.
It is possible to modify the value of the PR878 using the command SC041 Modification of the commercial
vehicle idle speed.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V48_PR878/SID304_V4D_PR878/SID301_V4C_PR878

13B-257
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR879
MAXIMUM AUTHORISED SPEED
PARAMETER
DEFINITIONThis parameter indicates the maximum permitted speed of the optional restriction in
mph (km/h).
NOTESThere must be no faults present. Perform fault finding after obtaining a parameter
inconsistency.
It is possible to modify the value of PR879 using command SC040 Speed limiter.
For Kangoo II only.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80°C, without electrical consumers
If the function has been activated, ET741= ACTIVE and the restricted speed of PR879 is between the range
18 mph (30 km/h) < PR879 < 150 mph (250 km/h).
It is possible to modify the value of PR879 using command SC040 Speed limiter.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V48_PR879/SID304_V4D_PR879/SID301_V4C_PR879

13B-258
MR-372-J84-13B050$819.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of commands
SPECIAL COMMAND
SC001: Enter saved data.
SC003: Save computer data.
SC013: Enter VIN.
SC017: Particle filter regeneration (Only for vehicles equipped with a particle filter).
SC040: Speed limiter (Kangoo II only).
SC041: Modification of the commercial vehicle idle speed (Kangoo II only).
CLEARING
RZ001: Fault memory.
Enables the faults to be cleared from the computer memory.
RZ002: EGR adaptives.
Use this command at the time of replacement or when cleaning the EGR valve.
RZ004: Pressure regulation adaptives.
This mode initialises the variables related to the regulation function.
RZ005: Programming (except Kangoo II).
This command enables you to reinitialise all the computer data (engine adaptives, EGR, rail, etc.).
RZ019: Reinitialise programming.
This mode initialises all of the programming contained in EEPROM.
RZ030: Particle filter adaptives (Vdiag 45, 49 and 4D only).
This mode initialises the variables related to the particle filter function.
ACTUATION
AC003: Fuel pressure solenoid valve.
AC005 to AC008: Injectors for cylinders 1 to 4.
Running this lets you listen to the operation of the injector on the cylinder in question.
AC012: Damper valve (except Vdiag 4C).
Activating this lets you listen to the operation of the damper valve.
AC029: High-pressure circuit seal check.
Running this lets you check the high pressure circuit sealing after an operation has been carried out.
Run this command with the engine running and the engine coolant temperature above 60°C.
MR-372-J84-13B050$819.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4CProgram No.: B1 and B2

13B-259
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
AC037: Preheating relay.
Activating this lets you listen to the operation of the preheating relay and enables the warning light in the
instrument panel to be illuminated.
AC079: Static actuator test.
Activating this allows you to activate the injection system actuators (simultaneously runs commands
AC003, AC005 to AC008, AC012, AC037, AC213, and AC214).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC099: Inhibition of electrical consumers.
AC100: Cancel inhibition of electrical consumers.
AC213: Fuel flow solenoid valve.
AC214: Turbocharger control solenoid valve.
Activating this allows you to listen to the operation of the turbocharger control solenoid valve.
AC233: Thermoplungers no. 1 and no. 2 (Vdiag 45, 49 and 4D only).
AC234: Thermoplunger no. 3 (Vdiag 45, 49 and 4D only).
AC235: Thermoplunger no. 4 (Vdiag 45, 49 and 4D only).
AC236: Coolant pump relay (only for vehicles equipped with a particle filter, except KANGOO II).
AC237: Fuel pump relay (only for vehicles equipped with a particle filter).
Activating this allows you to check the sealing on the 5
th particle filter injector circuit.
AC238: Particle filter injector (Only for vehicles equipped with a particle filter).
AC239: Particle filter temperature sensor fault finding (only for vehicles equipped with a particle filter).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC260: Thermoplunger relay.
Activating this allows you to check the three thermoplunger relays.

13B-269
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
AC236
COOLANT PUMP RELAY
NOTESThis command is used to check the operation of the electric coolant pump relay.
Use the CLIO III, MODUS, MEGANE II ph2 and SCENIC II ph2 Wiring Diagrams
Technical Note.
Vdiag 45, 49 and 4D only. (except Kangoo II).
Check the connection and condition of the coolant pump relay connector, component code 573 and injection
computer connector B, component code 120.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3VG between components 573 and 120,
–3V between components 573 and 369,
–3FB between components 573 and 983,
–3FB1 between components 573 and 983.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
SID304_V45_AC236 / SID304_V49_AC236 / SID304_V4D_AC236 / SID301_V4C_AC236

13B-270
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*temp.: temperatureAC239
PARTICLE FILTER TEMPERATURE SENSOR FAULT FINDING
NOTESCarry out this command only under the following conditions:
– DF999 Particle filter downstream temperature sensor circuit,
– DF1000 Particle filter upstream temperature sensor circuit,
With the ignition on and engine switched off and the engine coolant temperature
below 40°C.
This command is used to check the operation of the particle filter temperature sensors.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
If one of the faults such as DF999 Particle filter downstream temperature sensor circuit or DF1000 Particle
filter upstream temperature sensor circuit is stored, check if it is in short circuit to the + 12 V or in open circuit
using this command.
Procedure:
– Run command AC239 Particle filter temperature sensor fault finding in the presence of the one of these
two faults DF999 Particle filter downstream temperature sensor circuit and/or DF1000 Particle filter
upstream temperature sensor circuit.
– If one or both of these faults becomes present, then the sensor(s) is in short circuit to + 12 V or in open
circuit.
Refer to the interpretation of faults DF999 Particle filter downstream temperature sensor circuit and DF1000
Particle filter upstream temperature sensor circuit.
– If they do not become present, clear the faults on the CLIP diagnostic tool.
SID304_V4D_AC239 / SID304_V45_AC239 / SID304_V49_AC239 / SID301_V4C_AC239

13B-275
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 3 Starting difficult with cold engine
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the grade of the engine oil and that the engine oil level is correct.
Perform fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
Check the starter (see Technical Note 3632A, Starter fault finding).
Check the coolant temperature sensor, fuel sensor and air inlet sensor (refer to the interpretation of faults DF001
Coolant temperature sensor circuit, DF098 Fuel temperature sensor circuit and DF301 Air inlet circuit).
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the preheating system (refer to the interpretation of fault DF025 Preheating unit diagnostic line).
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check compression values.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP3 / SID304_V45_ALP3 / SID301_V48_ALP3 / SID304_V49_ALP3 / SID304_V4D_ALP3 / SID301_V4C_ALP3