2011 RENAULT SCENIC run flat

13B-140
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF209
CONTINUED 1
CC.1NOTESNone.
Check the condition of the connector of the EGR valve (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, Code organe1460).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation against +12 V and +5 V on the following connections:
– Connection code 3GC between components 1460 and 120.
– Connection code 3EL between components 1460 and 120.
– Connection code 3JM between components 1460 and 120.
Check the insulation between the following connections:
– Connection code 3GC between components 1460 and 120.
– Connection code 3VP between components 1460 and 120.
– Connection code 3EL between components 1460 and 120.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
EGR valve with a square connector:
Measure the resistances of the EGR valve between the following connections:
(sensor supply and sensor earth)
– Connection code 3GC of component 1460.
– Connection code 3JM of component 1460.
Replace the valve if the resistances are not between: 3.9 kΩ < X < 9.1 kΩ.
EGR valve with a flat connector:
Replace the EGR valve.
When replacing the EGR valve, run command SC036 Reinitialise programming and select EGR valve to
reinitialise the EGR valve offsets (see Replacement of components
).
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-154
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF272
CONTINUED 1
CONOTESNone.
Check the condition of the connector of the EGR valve (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, Component code 1460).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity of the following connections:
– Connection code 3VP between components 1460 and 120.
– Connection code 3VQ between components 1460 and 120.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EGR valve with a square connector:
Measure the resistance of the EGR valve between the following connections:
– Connection code 3VP of component 1460.
– Connection code 3VQ of component 1460.
EGR valve with a flat connector:
Replace the EGR valve.
Replace the valve if the resistance is not between 1 Ω When replacing the EGR valve, run command SC036 Reinitialise programming and select EGR valve to
reinitialise the EGR valve offsets (see Replacement of components).
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-155
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF272
CONTINUED 2
CC.0
CC.1NOTESNone.
Check the condition of the connector of the EGR valve (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, Code organe1460).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation from + 12 V of the following connections:
– Connection code 3VP between components 1460 and 120.
– Connection code 3VQ between components 1460 and 120.
Check the insulation against +5 V (computer supplies) of the following connections:
– Connection code 3VP between components 1460 and 120.
– Connection code 3VQ between components 1460 and 120.
Check the insulation against earth of the following connections:
– Connection code 3VP between components 1460 and 120.
– Connection code 3VQ between components 1460 and 120.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EGR valve with a square connector:
Measure the resistance of the EGR valve between the following connections:
– Connection code 3VP of component 1460.
– Connection code 3VQ of component 1460.
EGR valve with a flat connector:
– Replace the EGR valve.
Replace the valve if the resistance is not between 1 Ω When replacing the EGR valve, run command SC036 Reinitialise programming
and select EGR valve to
reinitialise the EGR valve offsets (see Replacement of components).
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-156
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF272
CONTINUED 3
CCNOTESNone.
Check the condition of the connector of the EGR valve (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, Component code 1460).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation between the following connections:
– Connection code 3VP between components 1460 and 120.
– Connection code 3VQ between components 1460 and 120.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EGR valve with a square connector:
Measure the resistance of the EGR valve between the following connections:
– Connection code 3VP of component 1460.
– Connection code 3VQ of component 1460.
EGR valve with a flat connector:
– Replace the EGR valve.
Replace the valve if the resistance is not between 1 Ω When replacing the EGR valve, run command SC036 Reinitialise programming and select EGR valve to
reinitialise the EGR valve offsets (see Replacement of components).
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-184
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF647
CONTINUED
Check the condition of the connector of the EGR valve (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, Component code 1460).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector(s) is/are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for continuity and absence of interference resistance of the following connections:
– Connection code 3GC between components 1460 and 120.
– Connection code 3JM between components 1460 and 120.
– Connection code 3EL between components 1460 and 120.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it
EGR valve with a square connector:
Measure the resistance of the EGR valve between the following connections:
– Connection code 3JM of component 1460.
– Connection code 3GC of component 1460.
EGR valve with a flat connector:
Replace the EGR valve.
Replace the valve if the resistance is not between: 3.9 kΩ When replacing the EGR valve, run command SC036 Reinitialise programming and select EGR valve to
reinitialise the EGR valve offsets (see Replacement of components).
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-245V9 MR-372-J84-13B450$132.mif
13B
ET415
CONTINUED 5
STATUS 7
Inconsistency between the request and the vehicle speed
Status ET415 changes to STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 changes to STATUS 7 when on flat or even terrain, contact the
Techline.
STATUS 8Automatic transmission in defect mode.
Status ET415 becomes STATUS 8 when driving with cruise control active (ET042:
Cruise control/speed limiter: CRUISE CONTROL) and if the automatic
transmission is in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic transmission
computer.
Deal with any present or stored faults (see 23A, Automatic transmission).
Clear the automatic transmission computer memory by running command RZ001
Fault memory.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If STATUS 8 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58