2011 RENAULT SCENIC light

13B-157
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF276
PRESENT
OR
STOREDINJECTOR CODE PROGRAMMING
1.DEF: No code stored
2.DEF: Internal electronic fault during programming
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the ignition has been switched on.
Special notes:
If the fault is present,
– torque limited, engine speed limited to 1500 rpm,
– engine torque limited,
–the level 1 warning light is illuminated.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
1.DEF
2.DEF
NOTESThis fault appears:
– when an incorrect injector code has been entered using
command SC002 Enter injector codes,
– after replacing the injection computer,
– after (re)programming.
EDC16C36_V44_DF276/EDC16C36_V4C_DF276/EDC16C36_V48_DF276/EDC16C36_V50_DF276/EDC16C36_V54_DF276/
EDC16C36_V58_DF276EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-159
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
PRESENT
OR
STOREDWATER IN DIESEL FUEL SENSOR
1.DEF: Open circuit on the line or water present in the diesel fuel
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on,
– a road test.
Special notes:
If the fault is present,
– risk of engine destruction if fault DF293 not taken into account,
– water in diesel warning light on.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
IMPORTANT
Please observe the cleanliness guidelines and safety advice.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF293/EDC16C36_V4C_DF293/EDC16C36_V48_DF293/EDC16C36_V50_DF293/EDC16C36_V54_DF293/
EDC16C36_V58_DF293EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-161
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
*diff: differential
*temp: temperature
DF308
PRESENT
OR
STOREDCLOGGED PARTICLE FILTER
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– the EGR function is inhibited,
– the vehicle performance is reduced,
–the level 1 warning light is lit and a warning message (or light) is displayed on the
instrument panel.
Priorities when dealing with a number of faults:
Deal with the following faults first:
– DF315 Particle filter differential pressure sensor if it is present.
– DF308 if DF315 is stored.
– DF316 Particle filter diff* pressure sensor if it is present or stored.
– DF226 Damper valve circuit if it is present or stored.
– DF272 EGR valve control circuit if it is present or stored.
– DF647 EGR valve position regulation if it is present or stored.
– DF309 Particle filter downstream temperature sensor if it is present or stored.
– DF899 Regeneration temperature threshold exceeded if it is present or stored.
– DF310 Particle filter upstream temperature sensor if it is present or stored.
– DF778 Turbine upstream temperature regulation if it is present or stored.
– DF652 Turbine upstream temperature sensor circuit if it is present or stored.
EDC16C36_V48_DF308/EDC16C36_V50_DF308/EDC16C36_V58_DF308EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-165
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF310
PRESENT
OR
STOREDPARTICLE FILTER UPSTREAM TEMP.* SENSOR
CO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
NOTESConditions for applying fault finding procedures to stored faults:
The fault becomes present if:
– ignition is on (CC.0),
– following a road test, engine warm (CO.1).
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
–the level 1 warning light is lit,
–the OBD warning light comes on after three consecutive driving cycles (start
+5 seconds, switch off the ignition and wait 1 minute).
IMPORTANT
The particle filter upstream temperature sensor only measures temperatures
above 50°C.
Use the Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V48_DF310/EDC16C36_V50_DF310/EDC16C36_V58_DF310EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-168
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait for the end of the power-latch phase and perform a road
test followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
13B
* diff: differential
*temp: temperature
DF311
PRESENT
OR
STOREDFAILED REGENERATIONS LIMIT EXCEEDED
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present,
–the level 1 warning light is illuminated.
– particle filter regenerations when driving are inhibited.
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
– DF308 Particle filter clogged if it is present or stored.
– DF315 Particle filter diff.* pressure sensor if it is present or stored.
– DF316 "Particle filter diff* pressure if it is present or stored"
– DF055 Turbocharging pressure regulation circuit if it is present or stored.
– DF309 Particle filter downstream temperature sensor if it is present or stored.
– DF899 Regeneration temperature threshold exceeded if it is present or stored.
– DF310 Particle filter upstream temperature sensor if it is present or stored.
– DF778 Turbine upstream temperature regulation if it is present or stored.
– DF652 Turbine upstream temperature sensor circuit if it is present or stored.
– DF272 EGR valve control circuit if it is present or stored.
– DF647 EGR valve position regulation if it is present or stored.
EDC16C36_V48_DF311/EDC16C36_V58_DF311
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-170
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF312
PRESENT
OR
STOREDSPEED REQUEST
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– the special regenerate particle filter warning light is lit or a warning message is
displayed on the instrument panel.
– The vehicle needs to be driven specially to activate particle filter regeneration during
driving.
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
– DF308 Particle filter clogged if it is present or stored.
– DF311 Failed regenerations limit exceeded if it is present.
– DF315 Particle filter diff* pressure sensor if it is present or stored.
The fault appears after:
– 7 failed regeneration attempts when driving and the weight of soot in the particle filter is greater than
21 g.
– the weight of soot in the particle filter is greater than 58 g.
PART A:
The flow chart on the following page can be used to analyse the driving profile and causes of the activation of this
fault.
EDC16C36_V48_DF312/EDC16C36_V58_DF312EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-173
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 3
PART B
1. No particle filter regeneration.
2. Write on the repair order the parameter and status relating to the last failure:
Mileage of last DF312
Mileage of last failures
Engine statuses of last failures
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3. Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the Particle Filter message or warning light illuminated (appeared at the Mileage of the
last DF312), the customer had not adhered to the driving recommendations: the failure that occurred at the
Mileage of the last failure is due to the engine being switched off.
4. Explain to the customer the procedure to turn off the warning light, making use of the parameters noted in the
repair order: see PA R T D.
PART C
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
Carry out an After-Sales regeneration with the consent of the Techline.
Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-174
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 4
PART D
Procedure to switch off the Particle filter message or warning light on the instrument panel
The customer must carry out a specific driving operation (cf. vehicle user manual) that consists of:
1. When the engine is warm, drive at a speed greater than 36 mph (60 km/h) for 1 minute to trigger the
regeneration procedure.
2. Keep driving at an average speed of 36 mph (60 Km/h), until the particle filter message or warning light on
the instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without stopping
the engine or leaving the engine running at idle speed for an extended period of time. The regeneration time
depends on the vehicle and driving conditions but should last for 20 minutes maximum.
3. If regeneration when driving fails (the warning light has not switched off or the service warning light has come
on), carry out a particle filter regeneration in the Renault dealership. Run command SC017 Particle filter
regeneration (see interpretation of commands).
Check that there are no leaks or blockages in the exhaust pipe.
Repair if necessary
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58