2011 RENAULT SCENIC edc16

13B-378
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
VP036INHIBIT FUEL SUPPLY
NOTESThis command enables you to disable the supply to the injectors.
This command is carried out with the engine switched off, and ignition on.
This command allows the injectors to be locked, so that starting is not possible.
Command VP036 allows the engine compressions to be checked in complete safety without disconnecting the
injector connectors or the TDC sensor.
Procedure to follow: (cylinder no. 1 is located on the flywheel end).
– Remove all the heater plugs, connect the compression gauge.
– Position the gear lever in neutral (manual gearbox) or on position P (automatic gearbox).
– Depress the brake pedal and maintain this position.
– Activate command VP036.
– Try to start the vehicle.
– Check the engine compressions.
Start the procedure again on another cylinder.
WARNING
Keep the brake pedal depressed for the length of the test.
Re-establish control of the injectors using command VP037 Stop fuel supply inhibition.
EDC16C36_V44_VP036/EDC16C36_V4C_VP036/EDC16C36_V48_VP036/EDC16C36_V50_VP036/EDC16C36_V54_VP036/
EDC16C36_V58_VP036EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-379
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
VP037CANCEL FUEL SUPPLY INHIBITION
NOTESThis command restores the fuel supply to the injectors.
This command is carried out with the engine switched off, and ignition on.
The command allows the supply to the injectors to be re-established, following an engine compression test.
Run command VP037, and try to start the vehicle.
If the vehicle does not start, start the procedure again.
EDC16C36_V44_VP037/EDC16C36_V4C_VP037/EDC16C36_V48_VP037/EDC16C36_V50_VP037/EDC16C36_V54_VP037/
EDC16C36_V58_VP037EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-380V9 MR-372-J84-13B450$180.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
NOTESOnly refer to these customer complaints after a complete check with the diagnostic
tool.
No dialogue with engine management computer ALP1
Starting difficult or impossibleALP2
Poor performanceALP4
Irregular engine operationALP5
External leaks from the fuel circuit ALP6
Rough idleALP7
Oil leaks from the turbocharger ALP8
Noises of the turbochargerALP9
Exhaust fumesALP10
Particle filter warning light comes on too often ALP11
DIESEL INJECTION
Fault finding – Customer complaints

13B-381
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
13B
ALP1 No dialogue with engine management computer
STEP 1
Check the conformity of the vehicle type and the domain selected on the tool.
Check that the tool is not faulty by trying to establish dialogue with a computer on another vehicle.
Check the supply to the diagnostic socket:
+ Before ignition.
+ After ignition.
Earth.
Check (according to wiring diagram and equipment):
– The conformity of the after ignition fuse.
– The conformity of the injection relay mounting.
The conformity of the injection relay:
65 Ω ± 5 between the following connections:
– Connection code BP37 of component 983.
– Connection code 3AA of component 983.
infinite resistance between connections (open contact):
– Connection code BP37 of component 983.
– Connection code 3FB of component 983.
resistance < 0.2 Ω between the following connections (contact closed):
– Connection code BP37 of component 983.
– Connection code3FB of component983.
Disconnect the engine management computer and check that there are no conducting parts on the computer
studs. If this reveals any kind of impurity, rectify it and try to establish dialogue.
If the fault is still present, place the bornier Elé. 1681 on the engine harness:
Check for continuity and absence of interference resistance on the following multiplex connections:
– Connection code 133B between components 120 and 225.
– Connection code 133C between components 120 and 225.
Check for + 12 V on connections 3FB and AP29 of component 120.
Check for earth on connections NT of component 120.
A
EDC16C36_V44_ALP01/EDC16C36_V4C_ALP01/EDC16C36_V48_ALP01/EDC16C36_V50_ALP01/EDC16C36_V54_ALP01/
EDC16C36_V58_ALP01
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-382
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP1
CONTINUED
If there is no + 12 V, carry out the following operations:
Shunt the normally open contact of the central injection unit supply relay, i.e. connections BP37 and 3FB of
component 983.
Check for + 12 V on connections 3FB and AP29 of component 120.
Check the continuity of the connection between:
– Connection code 3AA between components 120 and 983.
Try to establish dialogue with another computer on the same vehicle.
If dialogue is established with another computer on the same vehicle, go to step 2.
If dialogue cannot be established with any other computer on the same vehicle (see 88B, Multiplexing, ALP).
STEP 2
Contact the Techline.
A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-383
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2 Starting difficult (or impossible)
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
Is it difficult or impossible to start the engine?
PART A:
Check the engine earths.
If the engine speed is less than 200 rpm, refer to Technical Note 6014A, Checking the charging circuit, Starter
fault finding, Starter.
If an engine speed of 200 rpm is achieved with starter motor in operation, PR055 Engine speed.
If the engine speed shown on CLIP is zero and the engine is running, check the resistance of the engine speed
sensor between the following connections:
– Connection code 3BG,
– Connection code 3BL,
of component 149.
Replace the sensor if the resistance is not between 200 Ω and 270 Ω at 20°C.
Check the continuity and insulation of the following connections:
– Connection code 3BG,
– Connection code 3BL,
between components 120 and 149.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Replace if necessary.
Check the synchronisation of the camshaft sensors and the engine speed sensors with the display of ET238
Synchronisation. If synchronisation is not active, refer to the checks described in DF195 Camshaft/engine
speed consistency.
Check the fuel circuit for leaks using test 3 Low pressure circuit check.
If test 3: Low pressure circuit check is correct.
PART
B
Impossible
Difficult
EDC16C36_V44_ALP02/EDC16C36_V4C_ALP02/EDC16C36_V48_ALP02/EDC16C36_V50_ALP02/EDC16C36_V54_ALP02/
EDC16C36_V58_ALP02EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-384
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2
CONTINUED 1
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
Check that the heater plugs are actuated using the AC037 Preheating relay command.
Check the tightness and the condition of the inlet circuit: run test 4: Turbocharged air inlet circuit check and
follow the procedure.
Check that the exhaust is not blocked, run test 1 Exhaust system check and follow the procedure.
Check the consistency of the signal from the engine coolant temperature sensor.
Check the operation of the rail pressure regulator (DRV) using command AC011 Rail pressure regulator.
Check the timing setting.
End of part A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-385
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2
CONTINUED 2
Is there diesel fuel in the fuel tank?Fill the tank with diesel fuel.
Bleed the low and high pressure diesel circuit.
Does the starter motor work properly?
Ensure that the engine speed reaches PR055
Engine speed > ~ 200 rpm with the starter in
operation, Consult Technical Note 6014A, Checking the
charging circuit, 16A, Starter fault finding,
Starter.
Using the diagnostic tool, check the conformity of the immobiliser: ET003 Immobiliser must be INACTIVE.
ET003 not
in order, or
immobiliser warning light
permanently onET003 correct
(immobiliser code
warning light off)
Consult the fault finding procedure for the
immobiliser.Continue the fault finding procedure with Part A
of this fault finding chart.
PART
B
NO
YES
NO
YES
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58