2011 RENAULT SCENIC edc16

13B-402
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP11
CONTINUED 3
– Check the consistency between the IMA codes read on the CLIP diagnostic tool and the codes engraved on
the injector bodies,
– Check that the particle filter differential pressure sensor is correctly positioned and connected (see MR 364
(Megane II) or 370 (Scenic II), Mechanical, 19B Exhaust, Particle filter pressure sensor: Removal -
Refitting),
– Check the exhaust pipe see (Test1 Exhaust pipe check),
– Check the air inlet circuit see (Test 4 Turbocharged air inlet circuit check),
– Check the air flowmeter, (see Test 5 Air flowmeter),
– Check the turbocharger, (see Test 6 Turbocharger control solenoid valve test and Test 7 Turbocharger),
– Check the injectors, (see Test 10 Poor injector operation),
– Check the cylinder compressions.
If the fault has not been located and the customer complaint is still present, contact the Techline.
A
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-403
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
Analysis of output for ALP11 Particle filter warning light comes on too frequently
ALP11
CONTINUED 4
ALP
output no.ALP 11 output
conditionsCause - type of drivingRegeneration
frequencyWhat to tell the
customer?
Output 1The last 10
regeneration attempts
have failed due to the
engine cutting out.Regeneration failures
caused by engine cut-
off.No regeneration
frequency
analysis.Explain to the customer
the need to wait until the
end of regeneration
(warning light goes out)
before switching off the
engine.
Output 2The last 10
regeneration attempts
have failed, but not
because of the engine
cutting out.Unsuitable driving
conditionsNo regeneration
frequency
analysis.Explain to the customer
the driving criteria for
when the warning light
comes on.
Output 3After successful
regenerations stored in
the memory, the
warning light did not
come on. An interval
cannot be calculated.Since the last successful
stored regenerations, the
driving conditions have
not allowed the warning
light to come on.Should be normal Vehicle correct
Output 4The interval between a
successful
regeneration and the
particle filter warning
light coming on is
correct (above the
lowest possible
values). The system
does not have any
irregular components.Unfavourable driving
(urban zone, underspeed,
etc.)Normal Vehicle correct
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-404V9 MR-372-J84-13B450$200.mif
13B
*Technical Note 3419: Fault finding on the turbocharger for petrol and diesel enginesExhaust system check: TEST 1
Air line at the turbocharger TEST 2
Low pressure circuit check TEST 3
Checking the turbocharged air inlet circuit TEST 4
Air flow sensorTEST 5
Turbocharger control solenoid valve testTEST 6:
Run TEST 4 of
Technical Note 3419*
TurbochargerTEST 7:
Run TEST 7 of
Technical Note 3419*
Temperature upstream of turbine too low TEST 8
High pressure fuel circuit test TEST 9
Incorrect injector operation TEST 10
Diesel fuel conformity check TEST 11
Manual clearing of weight of soot TEST 12
DIESEL INJECTION
Fault finding – Tests
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-405V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST1 Exhaust system check:
Engine stopped: Check that the silencer outlet is not blocked.
Repair or replace the silencer, if necessary.
Check the seal of the exhaust manifold on the contact surface
between the turbocharger and the exhaust manifold.
Is the seal in order?Repair or replace the faulty part.
Loosen the catalytic converter on the turbocharger side.
Place a wooden block between the two parts.
Start the vehicle and check if the engine runs better.
Is the engine running normally?The exhaust pipe is not the cause of
the fault, repeat the engine fault
finding (see Customer complaints -
Fault finding chart (ALP)).
Retighten the catalytic converter.
Loosen or disconnect the intermediate chamber on the catalytic
converter side. Place a wooden block between the two parts if
necessary.
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the catalytic converter.
Retighten the intermediate chamber.
Loosen or disconnect the silencer on the intermediate chamber
side. Place a wooden block between the two parts, if
necessary.
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the intermediate chamber.
Replace the silencer.
YES
NO
YES
NO
YES
NO
YES
NO
YES
EDC16C36_V44_TEST1/EDC16C36_V4C_TEST1/EDC16C36_V48_TEST1/EDC16C36_V50_TEST1/EDC16C36_V54_TEST1/
EDC16C36_V58_TEST1
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-406V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST2 Turbocharger air chain
Check for the air filter
Check the replacement interval of the air filter on the maintenance booklet.
Compare the part numbers of the air filter fitted to the vehicle and that of the air filter recommended by the
manufacturer.
Check the air filter direction of fitting.
Is the air filter fitted to the vehicle correct?
Check the condition of the air filter
Visually inspect the condition of the filtering section of the air
filter.
Is either the air filter or its seal damaged?
Is the air filter fouled (does it contain a lot of impurities)?Replace the air filter (see MR 364
(Mégane II) or 370 (Scénic II),
Mechanical, 12A, Fuel mixture, Air
filter, Removal - Refitting).
Low pressure circuit check
Note:
Depending on the vehicle type, the best visual access will be
either from above or from below.
Visually inspect the condition of the following components:
– fresh air inlet scoop on the front panel of the vehicle,
– air inlet pipe to the air filter,
– air pipe of the filter until the compressor inlet,
– mountings of the air flowmeter.
Is one of these components incorrect (disconnected,
cut, bent, pierced or kinked pipes)?Replace the defective parts (see MR
364 (Mégane II) or 370 (Scénic II),
Mechanical systems, 12B,
Turbocharging).
YESNO
YES
NO
YES
NO
A
EDC16C36_V44_TEST2/EDC16C36_V4C_TEST2/EDC16C36_V48_TEST2/EDC16C36_V50_TEST2//EDC16C36_V54_TEST2/
EDC16C36_V58_TEST2
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-407V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST2
CONTINUED 1
High pressure circuit check
Note:
Depending on the vehicle type, the best visual access will be either from
above or from below.
Visually inspect the condition of the following components:
– outlet pipe of the compressor to the turbocharging air cooler,
– outlet pipe of the turbocharging air cooler to the inlet manifold,
– inlet manifold,
– temperature and pressure sensors.
Is one of these components incorrect (disconnected, cut, bent,
pierced or kinked pipes)?
Replace the defective parts
(see MR 364 (Mégane II) or
370 (Scénic II),
Mechanical, 12B,
Turbocharging). Exhaust system check
Visually inspect the condition of the following engine sections:
– from the exhaust manifold circuit to the turbocharger turbine,
– from the turbine outlet pipe to the end of the exhaust pipe,
– from the inlet manifold to the EGR valve
– check that the temperature and pressure sensors are connected.
Do some of these components have black or white marks on them?
Run test 6: Turbocharger control solenoid valve test.
A
YES
NO
YES
NO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-408V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST3 Low pressure circuit check
HIGH PRESSURE PUMP
Check the fuel filter:
– Conformity of the fuel filter (correct part number and RENAULT filter),
– positioning and clogging condition of the filter cartridge,
– Positioning and condition of the seals.
– if there is metal swarf in the filter:
Replace the fuel filter, bleed the circuit and continue the fault finding procedure.
●Supplying the injection system with fuel from an additional tank.
This operation aims to detect possible faults in the low pressure supply system of a vehicle by replacing it entirely with
an additional tank.
Mode:
– Disconnect the diesel fuel supply pipe at the fuel filter inlet and seal it with a plug.
– Connect a pipe to the fuel filter inlet and insert the other end in a clean container of approximately 5litres.
– Disconnect the diesel return pipe at the diesel temperature sensor (pump return and injector return join), and block
it using a plug.
– Connect a transparent pipe to the union of the diesel temperature sensor, and insert the other end in the container.
– Fill the container with clean diesel fuel.
– Start the engine and let the system drain itself of its air (there must not be any air bubbles in the return pipe).
Is the customer complaint still present?If the low pressure circuit is in order, reconnect
the various pipes of the low pressure circuit and
repeat the fault finding chart fault finding or of
the fault that referred you to this test.
Are the low pressure circuit connections in order
and in good condition?Carry out the necessary repairs.
YES
NO
NO
YES
A
EDC16C36_V44_TEST3/EDC16C36_V4C_TEST3/EDC16C36_V48_TEST3/EDC16C36_V50_TEST3/EDC16C36_V54_TEST3/
EDC16C36_V58_TEST3
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-409V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST3
CONTINUED
Check the condition and operation of the priming bulb.
Perform repairs if necessary and continue the test.
Check the condition of all the low pressure diesel pipes from the tank to the injection pump (in particular no pinching
of pipes).
If the fault is still present with a low fuel level, check the consistency of the actual fuel level and that indicated on
the instrument panel.
– The transfer pump is supplied via a Venturi pipe mounted underneath it.
Check that the opening of the venturi (6 to 8 mm in diameter) is not blocked by dirt contained in the fuel tank.
Check the priming of the low pressure diesel circuit.
Check the conformity of the fuel used by running test 11 Diesel fuel conformity check:
– Compare the fuel with some clean diesel in order to detect petrol, solvent, thinners, sulphuric acid (fuel will have
a whitish appearance), water or fuel oil.
If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low and high pressure diesel circuit.
Low pressure circuit correct.
A
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58