2011 RENAULT SCENIC check

DIESEL INJECTION
Fault finding - Interpretation of statuses13B
13B-150V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET004
AC AUTHORISED
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
YES
NO
The air conditioning authorisation only changes to YES if:
– the air conditioning request has been made by the driver (air conditioning switch in AC
or AUTO position with minimum ventilation),
– the engine is not under full load,
– the air conditioning system is not faulty.
The status ET004 remains at NO" in the following conditions:
– Vehicle stopped with the ignition on,
– faults present in the air conditioning circuit,
– no air conditioning request made by the driver,
– engine under full load.
If status ET004 remains at NO then the air conditioning should be authorised, check:
– that the air conditioning compressor is activated correctly,
– the air conditioning system feed fuses,
– for gas in the air conditioning circuit,
– the gas pressure value is consistent at idle speed.
If the fault is still present, check the air conditioning computer for faults (See 62A, Air
conditioning).
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET004/EDC16_V48_ET004/EDC16_V4C_ET004

DIESEL INJECTION
Fault finding - Interpretation of statuses13B
13B-151V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET007
PRE-POSTHEATING UNIT CONTROL
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
YES
NO
When the vehicle is started from cold, the injection computer controls the pre/postheating
unit so that the vehicle can be started.
Status ET007 changes to YES a few seconds after the ignition is switched on and during
pre/postheating.
If the vehicle does not start and status ET007 changes to YES, check:
–the F2 (70A) supply fuse on the preheating unit,
– the resistance of the heater plugs.
Replace any plugs with a resistance greater than 2 Ω.
If the vehicle starts and the status ET007 remains YES during the engine functional
stage, refer to the interpretation of faults:
DF017 Preheating relay control circuit.
DF025 Pre-postheating unit diagnostic connection.
After the engine is started and preheating, the injection computer should stop the pre/
postheating unit operating.
Status ET007 Should change to NO.
In the event that the vehicle does not start and status ET007 remains at NO, check the
continuity and the absence of interference resistance of the following connections:
Injection computer grey 32-track connector C, track A4 Track 9 preheating
unit
Injection computer grey 32-track connector C, track E2 Track 8 preheating
unit
Repair if necessary.
If the fault is still present, refer to the interpretation of faults:
DF017 Preheating relay control circuit.
DF025 Pre-postheating unit diagnostic connection.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET007/EDC16_V48_ET007/EDC16_V4C_ET007

13B-152
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET014
FAN ASSEMBLY 1 CHECK
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
Note: Status ET022 Low-speed engine fan request and status ET014 Engine fan assembly check 1 change
their status at the same time.
RUNNING
The low-speed fan assembly is supplied in three scenarios:
– the engine coolant temperature is above 89°C,
– the air conditioning is operating,
– the injection computer has system faults that could lead to the engine overheating.
When the low-speed fan assembly is supplied:
– status ET014 changes to RUNNING
– status ET022 low-speed engine fan request changes to ACTIVE.
In the event that the low-speed engine fan does not work, refer to the UPC fault finding note.
STOPPED
The low-speed fan assembly stops when:
– the engine coolant temperature is below 89°C,
– no air conditioning request made by the driver.
IMPORTANT!WARNING
If the UPC does not detect the injection computer frames, the low-speed engine
fan assembly is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is defective, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET014/EDC16_V48_ET014/EDC16_V4C_ET014

13B-153
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET015
FAN ASSEMBLY 2 CHECK
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
Note: Status ET015 Engine fan assembly 2 and status ET021 High-speed engine fan request change their
status at the same time.
RUNNING
The engine fan assembly can be supplied when:
– the engine coolant temperature is above 99°C.
– the injection computer has system faults that could lead to the engine overheating.
When the high speed fan is supplied:
– status ET015 changes to RUNNING
– status ET021 low-speed engine fan request changes to ACTIVE.
In the event that the high-speed engine fan does not work, refer to the UPC fault finding note.
STOPPED
The high-speed fan assembly stops when:
– the engine coolant temperature is below 99°C;
IMPORTANT!WARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is defective, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET015/EDC16_V48_ET015/EDC16_V4C_ET015

13B-154
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET021
HIGH-SPEED FAN REQUEST
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
Note: Status ET021 High-speed engine fan assembly request and status ET015 High-speed engine fan 2
test change their status at the same time.
ACTIVE
The injection computer requests the activation of the high speed GMV when:
– the engine coolant temperature is above 99°C.
– the injection computer has system faults that could lead to the engine overheating.
When the high speed fan is supplied:
– status ET021 High-speed engine fan request changes to ACTIVE.
– status ET015 changes to RUNNING
In the event that the high-speed engine fan does not work, refer to the UPC fault finding note.
STOPPED
The high-speed fan assembly stops when:
– the engine coolant temperature is below 99°C;
– no fault which could cause engine overheating is present in the injection system.
IMPORTANT!WARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is defective, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET021/EDC16_V48_ET021/EDC16_V4C_ET021

13B-155
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
Note: Status ET022 Low-speed engine fan request and status ET014 Engine fan assembly check 1 change
their status at the same time.ET022
LOW-SPEED FAN REQUEST
NOTESOnly perform the tests if the statuses do not correspond with the system programming
functions.
ACTIVE
The injection computer requests the activation of the low speed GMV when:
– the engine coolant temperature is above 89°C,
– the injection computer has system faults that could lead to the engine overheating,
– the air conditioning is switched on by the driver.
When the high speed fan is supplied:
– status ET022 High-speed engine fan request changes to ACTIVE,
– status ET014 changes to RUNNING.
In the event that the low-speed engine fan does not work, refer to the UPC fault finding note.
STOPPED
The low-speed fan assembly stops when:
– the engine coolant temperature is below 89°C,
– no fault which could cause engine overheating is present in the injection system.
– the air conditioning is not switched on by the driver.
IMPORTANT!WARNING
If the UPC does not detect the injection computer frames, the low speed engine
fan is supplied until the battery is completely discharged.
In the event that the low-speed engine fan assembly is defective, the high-speed
engine fan assembly will then be activated.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET022/EDC16_V48_ET022/EDC16_V4C_ET022

13B-156
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET038
ENGINE
STOPPEDStatus ET038 is stopped if the engine ignition is on but there has been no starter
operation.
STALLEDStatus ET038 is stalled when the engine has stalled. The vehicle is still under + after
ignition feed.
RUNNINGStatus ET038 is running if the engine has started.
STARTINGStatus ET038 is starter if the engine is in starting phase.
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET038/EDC16_V48_ET038/EDC16_V4C_ET038

DIESEL INJECTION
Fault finding - Interpretation of statuses13B
13B-157V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET042
CRUISE CONTROL/SPEED LIMITER
STATUS DEFINITION
NOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the cruise control/speed limiter main On/Off
switch is in the rest (or neutral) position.
SPEED LIMITER: This status indicates that the driver has used the main switch to
select the speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOT
DETECTED
If the vehicle does not have cruise control or speed limiter function buttons, status ET042
is permanently NOT DETECTED. This confirms that the cruise control/speed limiter
function is not present on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons, the main switch
is in the rest (or neutral) position and the injection computer has just been programmed
or reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the cruise
control position and then in the speed limiter position.
Return to rest position
The tool displays status ET042 INACTIVE.
If not, several steps must be checked:
1 Return to the multiplex network test page on the Clip application. Repeat the multiplex
network test. Re-establish dialogue with the injection computer. Check status ET042.
If ET042 is INACTIVE, the injection computer has detected the various positions of the
main switch. The cruise control/speed limiter is activated.
2 If ET042 is NOT DETECTED, check that the owner of the vehicle has not, sometime
in the past, asked for the cruise control/speed limiter function to be deactivated.
Contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V44_ET042/EDC16_V48_ET042/EDC16_V4C_ET042