2011 Ram 5500 Chassis Cab Owner's Manual

TOWING A DISABLED VEHICLE
Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for the purpose, following equip-
ment manufacturer’s instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to
the main structural members of the vehicle—not to
bumpers or associated brackets. State and local laws
applying to vehicles under tow must be observed.
Four-Wheel Drive Vehicles
CAUTION!
To avoid damage to the transfer case while towing,
always use one of the following methods.NOTE:
The transfer case must be in the NEUTRAL
position, and the transmission must be in PARK (auto-
matic transmission), or in gear (manual transmission) to
tow a four-wheel drive vehicle, unless all its wheels are
OFF the ground.
The manufacturer recommends towing with all wheels
OFF the ground. Acceptable methods are to tow the
vehicle on a flatbed or with one end of vehicle raised and
the opposite end on a towing dolly.
Two-Wheel Drive Vehicles
Provided that the transmission is operable, tow with the
transmission in NEUTRAL and the ignition key in the
OFF position along with the front wheels raised and the
rear wheels on the ground. Speed must not exceed
30 mph (50 km/h) and the distance must not exceed
15 miles (25 km).
376 WHAT TO DO IN EMERGENCIES

CAUTION!
Towing faster than 30 mph (50 km/h) or for more than
15 miles (25 km) can cause severe damage to the
transmission. Such damage is not covered by the
New Vehicle Limited Warranty.
If the vehicle is to be towed faster than 30 mph (50 km/h)
or more than 15 miles (25 km) the vehicle must be towed
with the rear wheels OFF the ground. It may be towed on
a flatbed, or with the front wheels raised and the rear
wheels on a dolly, or (when using a suitable steering
wheel stabilizer to hold the front wheels in the straight
position) with the rear wheels raised and the front wheels
on the ground.
6
WHAT TO DO IN EMERGENCIES 377

MAINTAINING YOUR VEHICLE
CONTENTS
Engine Compartment — 5.7L ............. 381
 Onboard Diagnostic System (OBD II) ....... 382
▫ Loose Fuel Filler Cap Message ........... 382
 Emissions Inspection And Maintenance
Programs ............................ 383
 Replacement Parts ..................... 384
 Dealer Service ........................ 385
 Maintenance Procedures ................. 385
▫ Engine Oil ......................... 386 ▫
Engine Oil Filter ..................... 388
▫ Engine Air Cleaner Filter ............... 388
▫ Maintenance-Free Battery .............. 389
▫ Air Conditioner Maintenance ............ 390
▫ Front Prop Shaft Lubrication – Four-Wheel
Drive Models ....................... 391
▫ Body Lubrication .................... 392
▫ Windshield Wiper Blades ............... 392
▫ Adding Washer Fluid ................. 393
7

▫Exhaust System ..................... 394
▫ Cooling System ..................... 396
▫ Brake System ....................... 401
▫ Rear Axle And 4X4 Front Driving Axle Fluid
Level ............................. 404
▫ Transfer Case ....................... 405
▫ Automatic Transmission ............... 405
▫ Appearance Care And Protection From
Corrosion .......................... 409
 Fuses .............................. 414
▫ Totally Integrated Power Module ......... 414
 Vehicle Storage ....................... 419 
Replacement Bulbs .................... 420
 Bulb Replacement ..................... 420
▫ Dual Or Quad Headlamp/Front Park And
Turn Signal – If Equipped .............. 420
▫ Fog Lamps – If Equipped .............. 422
▫ Center High-Mounted Stoplamp (CHMSL)
With Cargo Lamp .................... 423
▫ Cab Top Clearance Lamps – If Equipped .... 424
 Fluid Capacities ...................... 426
 Fluids, Lubricants And Genuine Parts ....... 427
▫ Engine ............................ 427
▫ Chassis ........................... 428
380 MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT — 5.7L
1 — Air Cleaner Filter7 — Washer Fluid Reservoir
2 — Automatic Transmission Dipstick 8 — Integrated Power Module
3 — Engine Oil Fill 9 — Power Steering Fluid Reservoir
4 — Engine Oil Dipstick 10 — Coolant Pressure Cap
5 — Brake Fluid Reservoir 11 — Engine Coolant Reservoir
6 — Battery
7
MAINTAINING YOUR VEHICLE 381

ONBOARD DIAGNOSTIC SYSTEM (OBD II)
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBDII. This system monitors
the performance of the emissions, engine, and automatic
transmission control systems. When these systems are
operating properly, your vehicle will provide excellent
performance and fuel economy, as well as engine emis-
sions well within current government regulations.
If any of these systems require service, the OBD II system
will turn on the Malfunction Indicator Light (MIL). It will
also store diagnostic codes and other information to
assist your service technician in making repairs. Al-
though your vehicle will usually be drivable and not
need towing, see your authorized dealer for service as
soon as possible.CAUTION!
•Prolonged driving with the MIL on could cause
further damage to the emission control system. It
could also affect fuel economy and drivability. The
vehicle must be serviced before any emissions
tests can be performed.
•If the MIL is flashing, severe catalytic converter
damage and power loss will soon occur. Immedi-
ate service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system determines
that the fuel filler cap is loose, improperly
installed, or damaged, a loose gascap indicator
will display in the EVIC telltale display area.
Refer to “Electronic Vehicle Information Center (EVIC) in
“Understanding Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly and press
382 MAINTAINING YOUR VEHICLE

the SELECT button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing. Normally, the OBD II system will be ready. The OBD II
system may
notbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over.
3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
7
MAINTAINING YOUR VEHICLE 383