2011 Peugeot 508 driver
[x] Cancel search: driverPage 47 of 340
2
45
Access
Emergency procedure
Emergency unlocking/
locking
using the electronic key
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:
- cell battery flat, vehicle battery discharged
or disconnected, ...
- vehicle located in an area with strong
electromagnetic emissions.
)
Pull on button 1
, to extract the integral key 2
.
)
Unlock or lock the vehicle using the key.
Manual locking
Driver's door
Inser t the key in the lock to lock or unlock the
door.
Passenger doors
)
On the rear doors, check that the child lock
is not on.
)
Remove the black cap located on the edge
of the door, using the key.
)
Inser t the key into the aper ture without
forcing, then without turning, move the latch
sideways towards the inside of the door.
)
Remove the key and refit the cap.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
)
First of all, use the key in the lock to unlock
or lock your vehicle.
)
Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT
dealer or a qualified workshop as soon as
possible.
Reinitialisation with the remote
control
)
Switch on the ignition.
)
Immediately press one of the remote
control buttons for a few seconds.
)
Switch off the ignition.
The remote control is fully operational again.
Page 48 of 340
46
Access
Changing the battery of the key
Battery ref.: CR2032/3 volts.
This replacement battery is available from a
PEUGEOT dealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is
needed.
)
Unclip the cover using a small screwdriver
at the cutout.
)
Lift off the cover.
)
Remove the flat battery from its location.
)
Fit the new battery into its location
obser ving the original direction of fitment.
)
Clip the cover onto the casing.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
Reinitialisation with the
electronic key
)
Switch of the ignition.
)
Immediately press one of the remote
control buttons for a few seconds.
)
Switch on the ignition
The electronic key is fully operational again.
Changing the battery of the
electronic key
Battery ref.: CR2032/3 volts.
This replacement battery is available from a
PEUGEOT dealer or a qualified workshop.
A message is displayed in the instrument panel
screen when replacement of the battery is
needed.
)
Unclip the cover using a pointed object at
the key ring.
)
Slide the flat battery out of its location.
)
Slide the new battery into its location
obser ving the original direction of fitment.
)
Clip the cover in place star ting at the front.
)
Reinitialise the electronic key.
Page 51 of 340
2
49
Access
Locking the vehicle
with exterior perimeter
monitoring only
Deactivate the interior volumetric and anti-lift
monitoring to avoid unwanted triggering of the
alarm in cer tain cases such as:
- leaving a window par tially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transpor tation by sea.
Deactivation of the interior
volumetric and anti-tilt monitoring
)
Switch of the ignition and within
ten seconds, press this button
until the indicator lamp is on
continuously.
)
Get out of the vehicle.
)
Press the locking button on
the remote control immediately
or lock the vehicle using the
Keyless Entry and Star ting
system.
The exterior perimeter monitoring alone is
activated: the indicator lamp in the button
flashes once per second.
To be effective, this deactivation must be carried
out each time the ignition is switched off.
Reactivation of the interior
volumetric and anti-tilt monitoring
Tr i g g e r i n g o f t h e a l a r m
This is indicated by sounding of the siren and
flashing of the direction indicators for thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times in
succession.
)
Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entry
and Starting system to deactivate
the exterior perimeter monitoring.
)
Press the locking button on the
remote control or lock the vehicle
using the Keyless Entry and
Starting system to activate all the
monitoring functions.
The indicator lamp in the button
again flashes once per second.
When the vehicle is unlocked using
the remote control or unlocked
using the Keyless Entry and Star ting
system, rapid flashing of the indicator
lamp in the button informs you that the alarm
was triggered during your absence. When
the ignition is switched on, this flashing stops
immediately.
Failure of the remote control
To deactivate the monitoring functions:
)
Unlock the vehicle using the key in the
driver's door lock.
)
Open the door; the alarm is triggered.
)
Switch on the ignition; the alarm stops. The
indicator lamp in the button switches off.
Locking the vehicle without
activating the alarm
)
Lock or deadlock the vehicle using the key
in the driver's door lock.
Operating fault
When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault in the system.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
*
According to country.
Automatic activation *
2 minutes after the last door or the boot is
closed, the system is activated automatically.
)
To avoid triggering the alarm on entering
the vehicle, first press the unlocking button
on the remote control or unlock the vehicle
using the Keyless Entry and Star ting
system.
Page 53 of 340
2
51
!
Access
Reinitialisation of the
electric windows
Always remove the key from the ignition
when leaving the vehicle, even for a
shor t time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When operating the passenger electric
window switches, the driver must
ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch function is not active
during these operations:
- lower the window completely, then raise
it, it will rise in steps of a few centimetres
each time the switch is pressed. Repeat
the operation until the window closes
completely,
- continue to press the switch for at least one
second after reaching this position, window
closed.
Page 57 of 340
2
55
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in
the event of a battery or central locking fault.
Unlocking
)
Fold back the rear seats to gain access to
the lock from inside the boot.
)
Inser t a small screwdriver into hole A
of the
lock to unlock the tailgate.
"Boot open" warning
With the engine running or when the vehicle is
moving, if the tailgate is not properly closed,
a message accompanied by an audible signal
(from 6 mph (10 km/h)) is displayed in the
instrument panel screen.
Page 59 of 340
2
57
!
Access
In the event of contact during operation
of the blind, you must reverse its
movement. To do this, turn the dial.
When the driver operates the dial, they
must ensure that nothing prevents the
blind from closing correctly.
The driver must ensure that the
passengers use the blind correctly.
Be aware of children during operation
of the blind.
Reinitialising the system
Following reconnection of the battery, or in the
event of a malfunction in its operation, it may be
necessary to reinitialise the system:
)
turn the dial to the fully open position,
)
wait until the blind is fully open,
)
then immediately press the dial for at least
3 seconds,
If the blind opens on its own when closing, as
soon as possible after the blind stops:
- put the dial in the fully closed position,
- press the dial,
- maintain pressure on the dial until the blind
closes.
The anti-pinch function is inoperative
during these operations.
Page 64 of 340
62
i
Comfort
Electric adjustments
Switch on the ignition or star t the engine if the vehicle has gone into economy mode.
1.
Adjustment of the seat cushion angle
and height, and forwards-backwards
adjustment
)
Raise or lower the front of the control to
adjust the seat cushion angle.
)
Raise or lower the rear of the control to
raise or lower the seat.
)
Simultaneously raise or lower the front
and rear of the control in order to raise or
lower the entire seat.
2.
Adjustment of the backrest angle
Move the control for wards or backwards to
adjust the backrest angle.
3.
Adjustment of lumbar support
This function allows you to independently
adjust the height and level of lumbar
support.
The electric functions of the driver's seat are active for about a minute after opening the
front door. They are deactivated about a minute after switching off the ignition and in
economy mode.
To reactivate them, switch on the ignition.
Move the control:
)
For wards or backwards to increase or
reduce the lumbar suppor t.
)
Upwards or downwards to raise or lower
the lumbar suppor t zone.
Page 65 of 340
3
63
Comfort
Storing driving positions
System which stores the electrical settings of
the driver's seat and door mirrors as well as
the head-up display settings. It enables you to
store up to two positions using the buttons on
the side of the driver's seat.
Storing a position
using buttons M/1/2
)
Switch on the ignition.
)
Adjust your seat, the door mirrors and the
head-up display.
)
Press button M
, then press button 1
or 2
within four seconds.
An audible signal indicates that the position
has been stored.
Storing a new position cancels the previous
position.
Recalling a stored position
Ignition on or engine running
)
Briefly press button 1
or 2
to recall the
corresponding position.
An audible signal indicates the end of the
adjustment.
You can interrupt the current movement by
pressing button M
, 1
or 2
or by using one of the
seat controls.
A stored position cannot be recalled while
driving.
Recalling stored positions is deactivated
45 seconds after switching off the ignition.
Welcome function
The welcome function assists entry and leaving
the vehicle.
After switching off the ignition and opening
the driver’s door, the seat moves back
automatically and then stays in this position,
ready for the next entry to the vehicle.
When switching on the ignition, the seat moves
for ward to the stored driving position.
When moving the seat, take care that no
person or object hinders the automatic
movement of the seat.
To activate or deactivate this function, contact
a PEUGEOT or a qualified workshop.