2011 PEUGEOT 207 headlamp
[x] Cancel search: headlampPage 144 of 248
9
i
ii
PRACTICAL INFORMATION
142
The headlamps are fi tted with polycar-
bonate glass with a protective coating:
)
do not clean them using a dry or
abrasive cloth, nor with a deter-
gent or solvent product,
)
use a sponge and soapy water,
)
when using a high pressure washer
on persistent marks, do not direct
at the lamps or their outlines for too
long, so as not to damage their pro-
tective coating and seals.
Front lamps CHANGING A BULB
Changing the direction indicator
bulbs
Amber coloured bulbs, such as the
direction indicators, must be re-
placed with bulbs of identical spec-
ifi cation and colour.
)
Turn the bulb holder one quarter of
a turn and remove it.
)
Pull the bulb then change it.
To r efi t, carry out these operations in re-
verse order.
1.
Direction indicators (PY21W amber).
2.
Sidelamps (W5W).
3.
Dipped beam headlamps (H7-55W).
4.
Main beam headlamps (H1-55W).
5.
Foglamps (H11-55W).
)
Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk
of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation. In some weather conditions (e.g.
low temperature or humidity), the
presence of misting on the internal
surface of the glass of the head-
lamps and rear lamps is normal;
it disappears after the lamps have
been on for a few minutes.
Page 145 of 248
9PRACTICAL INFORMATION
143
Changing the sidelamp bulbs
)
Disconnect the main headlamp con-
nector.
)
Remove the plastic protective cover
by pulling on the tab.
)
Turn the bulb holder one quarter of
a turn and remove it.
)
Pull the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
Changing the dipped or main beam
headlamp bulbs
)
Disconnect the main headlamp con-
nector.
)
Remove the corresponding plastic
protective cover by pulling on the
tab.
)
Disconnect the connector of the cor-
responding lamp.
)
Move aside the spring to release the
bulb and remove the bulb.
To r efi t, carry out these operations in re-
verse order.
Changing the foglamp bulbs
For replacement of these bulbs, contact a
PEUGEOT dealer or a qualifi ed workshop.
Changing the integrated direction
indicator side repeaters
)
Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.
)
Tilt the screwdriver to extract the re-
peater and remove the repeater.
)
Disconnect the repeater connector.
To r efi t, carry out these operations in re-
verse order.
To obtain a replacement repeater, contact
a PEUGEOT dealer or a qualifi ed work-
shop.
Page 147 of 248
9
!
PRACTICAL INFORMATION
145
Changing the third brake lamp bulbs
(4 bulbs W 5 W)
)
Press on the fi xing pins on each side
of the lamp.
)
Remove the lamp from the outside.
)
Turn the bulb holder which corresponds
to the faulty bulb one quarter of a turn
and remove it.
)
Pull the bulb and change it.
Changing the number plate lamp
bulbs (W 5 W)
)
Insert a thin screwdriver in one of
the exterior holes of the lens.
)
Push it towards the outside to unclip
it.
)
Remove the lens.
)
Pull the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist
on the headlamps, the lamps and
their surrounds, to avoid damag-
ing their protective coating and
seals.
Page 149 of 248
9
!
PRACTICAL INFORMATION
147
Changing the third brake lamp bulbs
(4 bulbs W 5 W)
)
Remove the two lamp fi xing nuts.
)
Remove the lamp from the outside.
)
Press on the two tabs and remove
the bulb holder
)
Pull the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
lamp.
Changing the number plate bulbs
(W 5 W)
)
Insert a thin screwdriver into one of
the exterior holes of the lens.
)
Push it towards the outside to unclip
it
)
Remove the lens.
)
Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist
on the headlamps, the lamps and
their surrounds, to avoid damag-
ing their protective coating and
seals.
Page 152 of 248
9PRACTICAL INFORMATION
150
Fuse N°
Rating
Functions
F8
20 A
Audio equipment, audio/telephone, multifunction
screen, clock, steering wheel controls, trailer
fusebox.
F9
30 A
Front 12 V socket, rear 12 V socket (SW).
F10
15 A
Not used.
F11
15 A
Diagnostic socket, low current ignition switch,
automatic gearbox control unit.
F12
15 A
Rain/sunshine sensor, amplifi er, trailer fusebox,
driving school module.
F13
5 A
Engine fusebox, ABS relay, dual-function brake
switch.
F14
15 A
Instrument panel, seat belt warning lamps panel,
headlamp adjustment, air conditioning, Bluetooth
system, rear parking sensors control unit, airbags.
F15
30 A
Locking.
F17
40 A
Heated rear screen and door mirrors.
SH
-
PARC shunt.
Page 153 of 248
9PRACTICAL INFORMATION
151
Engine compartment fuses
The fusebox is placed in the engine
compartment, near the battery (left-
hand side).
Access to the fuses
)
Unclip the cover.
)
Replace the fuse (refer to the cor-
responding paragraph).
)
When you have fi nished, carefully
close the cover carefully to ensure
correct sealing of the fusebox.
Fuse table
Fuse N°
Rating
Functions
F1
20 A
Engine control unit and fan assembly control relay
supply, timing and canister electrovalves (1.6 litre
16V THP), air fl ow sensor (Diesel), injection pump
(Diesel), water in diesel sensor (Diesel), EGR
electrovalves, air heating (Diesel).
F2
15 A
Horn.
F3
10 A
Front and rear screenwash.
F4
20 A
Headlamp wash.
F5
15 A
Fuel pump (petrol), Turbo electrovalves (1.6 l 16V
THP).
F6
10 A
Vehicle speed sensor, automatic gearbox.
F7
10 A
Electric power steering, switching and protection
unit (Diesel).
F8
25 A
Starter motor control.
F9
10 A
ABS/ESP control unit, brake pedal switch.
F10
30 A
Engine control unit actuators (petrol: ignition coils,
electrovalves, oxygen sensors, injectors, heaters,
electronic thermostat) (Diesel: electrovalves,
heaters).
F11
40 A
Air conditioning blower.
F12
30 A
Windscreen wipers Low/High speed.
Page 154 of 248
9PRACTICAL INFORMATION
152
Fuse N°
Rating
Functions
F13
40 A
Built-in systems interface supply (ignition positive).
F14
30 A
Diesel heater (Diesel).
F15
10 A
Left main beam headlamp.
F16
10 A
Right main beam headlamp.
F17
15 A
Left dipped beam headlamp.
F18
15 A
Right dipped beam headlamp.
*
The maxi-fuses provide additional
protection for the electrical systems.
All work on the maxi-fuses must be
carried out by a PEUGEOT dealer or
a qualifi ed workshop.
Maxi-fuse table
Fuse N°
Rating
Functions
Box 1
MF1 *
70 A
Fan assembly.
MF2 *
20 A/30 A
ABS/ESP pump.
MF3 *
20 A/30 A
ABS/ESP electrovalves.
MF4 *
60 A
Built-in systems interface supply.
MF5 *
60 A
Built-in systems interface supply.
MF6 *
30 A
Additional fan assembly (1.6 litre 16V THP).
MF7 *
80 A
Dashboard fusebox.
MF8 *
30 A
Not used.
Box 2
MF9 *
80 A
Heating unit (Diesel).
MF10 *
80 A
Electric power steering.
MF11 *
40 A
Valvetronic electric motor (1.6 litre 16V THP).
Page 157 of 248
9
i
i
PRACTICAL INFORMATION
155
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions according to the level of
charge remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as the air condition-
ing, the heated rear screen...
The deactivated functions are reactivat-
ed automatically as soon as conditions
permit.
A fl at battery prevents the engine
from starting (refer to the corre-
sponding paragraph).
If the telephone is being used at this
time, it will be maintained for 5 minutes
with your Peugeot Connect Sound's
Bluetooth system.
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
beam headlamps, courtesy lamps, etc.
for a maximum combined duration of
thirty minutes.
Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.
)
In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be
double the duration for which the engine
is left running. However, this period will al-
ways be between fi ve and thirty minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multifunction
screen indicating that the vehicle has
switched to economy mode and the ac-
tive functions are put on standby.
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.
Removing a front or rear wiper
blade
)
Raise the corresponding wiper arm.
)
Unclip the wiper blade and remove it.
Fitting a front or rear wiper
blade
)
At the front, check the size of the
wiper blade as the shorter blade is
fi tted on the right-hand side of the
vehicle.
)
Put the corresponding new wiper
blade in place and clip it.
)
Fold down the wiper arm carefully.