2011 LEXUS RX350 lights

199
2-3. Operating the lights and windshield wipers
2

When driving
nThe windshield wipers and washer can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nEffects of vehicle speed on wiper operation
Vehicle speed affects the following even when the wipers are not in “AUTO” mode:
lIntermittent wiper interval
lWiper operation when the washer is being used (delay until drip prevention
wiper sweep occurs)
When low speed wiper operation is selected, wiper operation will be switched from
low speed to intermittent wiper operation only when the vehicle is stationary.
(However, when the sensor sensitivity is adjusted to the highest, the mode cannot
be switched.)
Sensor sensitivity (high)
Sensor sensitivity (low)
Washer/wiper dual operation
The wipers will automatically
operate a couple of times after
the washer squirts.
(After operating several times,
the wipers operate one more
time after a short delay to pre-
vent dripping.)
If the headlights are on, the
headlight cleaners will operate
once.

200
2-3. Operating the lights and windshield wipers
nRaindrop sensor (vehicles with rain-sensing windshield wipers)
lIf the wiper switch is turned to the position while the “ENGINE START
STOP” switch is in IGNITION ON mode, the wipers will operate once to show
that “AUTO” mode is activated.
lWhen the sensor sensitivity ring is turned toward high while in “AUTO” mode,
the wipers will operate once to indicate that the sensor sensitivity is enhanced.
lIf the temperature of the raindrop sensor is 194°F (90°C) or higher, or 5°F
(-15°C) or lower, automatic operation may not occur. In this case, operate
the wipers in any mode other than “AUTO”.
nIf no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the wind-
shield washer fluid reservoir.
CAUTION
nCaution regarding the use of windshield wipers in “AUTO” mode (vehicles with
rain-sensing windshield wipers)
The windshield wipers may operate unexpectedly if the sensor is touched or the
windshield is subject to vibration in “AUTO” mode. Take care that your fingers or
anything else do not become caught in the windshield wipers.
lThe raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from the
rising or setting of the sun intermittently
strikes the windshield, or if bugs etc. are
present on the windshield.

201
2-3. Operating the lights and windshield wipers
2

When driving
NOTICE
nWhen the windshield is dry
Do not use the wipers, as they may damage the windshield.
nWhen the washer fluid tank is empty
Damage to the washer fluid pump may be caused if the lever is pulled toward you
and held continually.
nWhen a nozzle becomes blocked
Do not try to clear it with a pin or other object. The nozzle will be damaged.

202
2-3. Operating the lights and windshield wipers
Rear window wiper and washer
nThe rear window wiper and washer can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
NOTICE
nWhen the rear window is dry
Do not use the wipers, as they may damage the rear window.
nWhen the washer fluid tank is empty
Damage to the washer fluid pump may be caused if the lever is operated continu-
ally.
nWhen a nozzle becomes blocked
Do not try to clear it with a pin or other object. The nozzle will be damaged.
The wiper operation is selected by moving the lever as follows:
Off
Intermittent window
wiper operation
Normal window wiper
operation
Washer/wiper dual
operation
Washer/wiper dual
operation

203
2-3. Operating the lights and windshield wipers
2

When driving
Headlight cleaner switch∗
nThe headlight cleaner can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode and the headlight
switch is turned on.
nWindshield washer linked operation
When the windshield washer is operated with the “ENGINE START STOP” switch
in IGNITION ON mode and the headlights on, the headlight cleaner will operate
once. (→P. 1 9 7 )
NOTICE
nWhen the washer fluid tank is empty
Do not press the switch continually as the washer fluid pump may overheat.
Washer fluid can be sprayed on the headlights.
Press the switch to clean the
headlights.
∗: If equipped

215
2-4. Using other driving systems
2

When driving
nRadar sensor and grille cover
Always keep the sensor and grille cover clean to ensure that the vehicle-to-vehicle
distance control operates properly. (Some obstructions, such as snow, ice and plas-
tic objects, cannot be detected by the obstruction sensor.)
Dynamic radar cruise control is canceled if an obstruction is detected.
nWarning lights and messages for dynamic radar cruise control
Warning lights and messages are used to indicate a system malfunction or to inform
the driver of the need for caution while driving. (→P. 5 5 1 )
nApproach warning
In the following instances, there is a possibility that the approach warnings will not
occur:
lWhen the speed of the vehicle ahead matches or exceeds your vehicle speed
lWhen the vehicle ahead is traveling at an extremely slow speed
lImmediately after the cruise control speed was set
lAt the instant the accelerator is applied
Grille cover
Radar sensor

229
2-4. Using other driving systems
2

When driving
nRear view monitor system camera
nSmear effect
In the following cases, it may become diffi-
cult to see the images on the screen, even
when the system is functioning correctly:
lThe vehicle is in a dark area, such as at
night.
lThe temperature near the lens is
extremely high or low.
lWater droplets are on the camera lens
or humidity is high, such as when it
rains.
lForeign matter, such as snow or mud,
adheres to the camera lens.
lThe sun or headlights are shining
directly into the camera lens.
If a bright light, such as sunlight reflected
off the vehicle body, is picked up by the
camera, a smear effect* characteristic to
the camera may occur.
*: Smear effect ⎯ A phenomenon that
occurs when a bright light is picked up by
the camera; when transmitted by the
camera, the light source appears to have
a vertical streak above and below it.

238
2-4. Using other driving systems
Hill-start assist control
nHill-start assist control can be operated when
lThe shift lever is in a position other than P.
lThe parking brake is not applied.
lThe accelerator pedal is not depressed.
nHill-start assist control
lWhile hill-start assist control is operating, the brakes remain automatically
applied after the driver releases the brake pedal. The stop lights and the high
mounted stoplight turn on.
lHill-start assist control operates for about 2 seconds after the brake pedal is
released.
lIf the slip indicator does not flash and the buzzer does not sound when the brake
pedal is further depressed, slightly reduce the pressure on the brake pedal (do
not allow the vehicle to roll backward) and then firmly depress it again. If the sys-
tem still does not operate, check if the operating conditions explained above
have been met.
Hill-start assist control helps to prevent the vehicle from rolling backwards
when starting on an incline or slippery slope.
To engage hill-start assist con-
trol, further depress the brake
pedal when the vehicle is
stopped completely.
A buzzer will sound once to
indicate the system is activated.
The slip indicator will also start
flashing.