2011 LEXUS RX350 lights

520
4-3. Do-it-yourself maintenance
Remove the light bulb.
Tail light
Back-up light
nLights other than the above
If any of the lights listed below has burnt out, have it replaced by your
Lexus dealer.
lHeadlight low beams (discharge bulbs)
lHeadlight high and low beams (discharge bulbs)
lFront fog lights
lSide turn signal lights
lStop lights
lHigh mounted stoplight
lLicense plate lights
STEP3

521
4-3. Do-it-yourself maintenance
4

Maintenance and care
nDischarge headlights (if equipped)
If voltage to the discharge bulbs is insufficient, the bulbs may not come on, or may
go out temporarily. The discharge bulbs will come on when normal power is
restored.
nLED bulbs
The stop lights, side turn signal lights, license plate lights and high mounted stoplight
consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your
Lexus dealer to have the light replaced.
nCondensation build-up on the inside of the lens
Contact your Lexus dealer for more information in the following situations. Tempo-
rary condensation build-up on the inside of the headlight lens does not indicate a
malfunction.
lLarge drops of water are built up on the inside of the lens.
lWater has built up inside the headlight.

522
4-3. Do-it-yourself maintenance
CAUTION
nReplacing light bulbs
lTurn off the lights. Do not attempt to replace the bulb immediately after turning
off the lights.
The bulbs become very hot and may cause burns.
lDo not touch the glass portion of the light bulb with bare hands. Hold the bulb by
the plastic or metal portion.
If the bulb is scratched or dropped it may blow out or crack.
lFully install light bulbs and any parts used to secure them. Failing to do so may
result in heat damage, fire, or water entering the headlight unit. This may damage
the headlights or cause condensation to build up on the lens.
nDischarge headlights (if equipped)
lContact your Lexus dealer before replacing discharge headlights (including light
bulbs).
lDo not touch the discharge headlight’s high voltage socket when the headlights
are turned on.
An extremely high voltage of 20000 V will be discharged and could result in
serious injury or death by electric shock.
lDo not attempt to take apart or repair the low beam discharge headlight bulbs,
connectors, power supply circuits, or related components.
Doing so could result in electric shock and serious injury or death.
nTo prevent damage or fire
Make sure bulbs are fully seated and locked.

524
5-1. Essential information
Emergency flashers
NOTICE
nTo prevent battery discharge
Do not leave the emergency flashers on longer than necessary when the engine is
not running.
Use the emergency flashers if the vehicle malfunctions or is involved in an
accident.
Press the switch to flash all the
turn signal lights. To turn them
off, press the switch once again.

5

When trouble arises
547
5-2. Steps to take in an emergency
Have the vehicle inspected by your Lexus dealer immediately.
A buzzer sounds and a warning message is shown on the multi-informa-
tion display. Failure to investigate the cause of the following warnings may
lead to the system operating abnormally and possibly cause an accident.
Have the vehicle inspected by your Lexus dealer immediately.
Wa r n i n g m e s s a g eDetails
(If equipped)
Indicates a malfunction in the AWD system
Indicates that the automatic transmission fluid tem-
perature is too high
Indicates a malfunction in the brake lights system
Indicates a malfunction in the steering lock system

5

When trouble arises
577
5-2. Steps to take in an emergency
If the engine will not start
If the engine will not start even though correct starting procedures are
being followed (→P. 153), consider each of the following points.
nThe engine will not start, even though the starter motor operates
normally.
One of the following may be the cause of the problem:
lThere may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle.
lThe engine may be flooded.
Try to restart the engine again following correct starting proce-
dures. (→P. 1 5 3 )
lThere may be a malfunction in the engine immobilizer system.
(→P. 1 0 1 )
nThe starter motor turns over slowly, the interior lights and head-
lights are dim, or the horn does not sound or sounds at a low vol-
ume.
One of the following may be the cause of the problem:
lThe battery may be discharged. (→P. 584)
lThe battery terminal connections may be loose or corroded.
nThe starter motor does not turn over.
The engine starting system may be malfunctioning due to an electri-
cal problem such as an open circuit or a blown fuse. However, an
interim measure is available to start the engine. (→P. 5 7 8 )

578
5-2. Steps to take in an emergency
Emergency start function
When the engine does not start, the following steps can be used as an
interim measure to start the engine if the “ENGINE START STOP” switch
is functioning normally:
Set the parking brake.
Shift the shift lever to P.
Turn the “ENGINE START STOP” switch to ACCESSORY
mode.
Press and hold the “ENGINE START STOP” switch for about 15
seconds while depressing the brake pedal firmly.
Even if the engine can be started using the above steps, the system may
be malfunctioning. Have the vehicle inspected by your Lexus dealer.
nThe starter motor does not turn over, the interior lights and head-
lights do not turn on, or the horn does not sound.
One of the following may be the cause of the problem:
lOne or both of the battery terminals may be disconnected.
lThe battery may be discharged. (→P. 584)
lThere may be a malfunction in the steering lock system.
Contact your Lexus dealer if the problem cannot be repaired, or if
repair procedures are unknown.
STEP1
STEP2
STEP3
STEP4

5

When trouble arises
585
5-2. Steps to take in an emergency
nStarting the engine when the battery is discharged
The engine cannot be started by push-starting.
nTo prevent battery discharge
lTurn off the headlights and the audio system while the engine is off.
lTurn off any unnecessary electrical components when the vehicle is running at a
low speed for an extended period, such as in heavy traffic.
nWhen the battery is removed or discharged
The power back door must be initialized. (→P. 6 3 0 )
Connect a negative cable clamp to the negative (-) battery terminal
on the second vehicle
Connect the clamp at the other end of the negative cable to a solid,
stationary, unpainted metallic point away from the battery and any
moving parts, as shown in the illustration.
Start the engine of the second vehicle. Increase the engine
speed slightly and maintain that level for approximately 5 min-
utes to recharge the battery of your vehicle.
Open and close any of the doors with the “ENGINE START
STOP” switch off.
Maintain the engine speed of the second vehicle and start the
engine of your vehicle by turning the “ENGINE START STOP”
switch to IGNITION ON mode.
Once the vehicle’s engine has started, remove the jumper
cables in the exact reverse order from which they were con-
nected.
Once the engine starts, have the vehicle inspected at your Lexus
dealer as soon as possible.
STEP3
STEP4
STEP5
STEP6