2011 KIA CEED Owners Manual

769
Maintenance
Headlight bulb
1. Open the hood.
2. Remove the radiator upper cover(Type B).
3. Loosen the retaining bolts and remove the headlight assembly from the body
of the vehicle.
4. Disconnect the power connector from the back of the headlight assembly.
(Continued)
 If a bulb becomes damaged orcracked, replace it immediately
and carefully dispose of it.
 Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.
G270A03O
WARNING - Halogen bulbs
 Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
 Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never touchthe glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated onlywhen installed in a headlight.
(Continued)
OED079069
Type A
Type BOED070104
ED(FL) ENG 7.QXP 10/28/2010 6:28 PM Page 69

Maintenance
70
7
5. Remove the headlight bulb cover by
turning it counterclockwise.
6. Disconnect the headlight bulb socket- connector.
7. Unsnap the headlight bulb retaining wire by depressing the end and push-
ing it upward. (if equipped)
8. Remove the bulb from the headlight assembly. 9. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
10. Connect the headlight bulb socket connector.
11. Install the headlight bulb cover by turning it clockwise.
12. Connect the power connector to the back of the headlight assembly.
13. Reinstall the headlight assembly to the body of the vehicle.
Turn signal light
1. Remove the headlight assembly fromthe body of the vehicle.
2. Remove the socket from the assembly by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
OED070070
Type A
Type B
OED070105
OED070170
Type A
Type B
OED070106
ED(FL) ENG 7.QXP 10/28/2010 6:28 PM Page 70

771
Maintenance
3. Remove the bulb from the socket bypressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket
4. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
6. Reinstall the headlight assembly to the body of the vehicle.
Position light
1. Remove the headlight assembly fromthe body of the vehicle.
2. Remove the cover by turning it coun- terclockwise.
3. Remove the socket from the assembly.
4. Remove the bulb from the socket by pulling straight out. 5. Insert a new bulb.
6. Install the socket in the assembly.
7. Install the cover turning it clockwise.
8. Reinstall the headlight assembly to the
body of the vehicle.
OED070171
Type A
Type B
OED070106A
ED(FL) ENG 7.QXP 10/28/2010 6:28 PM Page 71

Maintenance
72
7
Front fog light bulbs (if equipped)
1. Remove the front bumper under cover.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulb-socket from the housing by turning the socket counter
clockwise until the tabs on the socketalign with the slots on the housing.
5. Install the new bulb-socket into the housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover. Side repeater light bulb replace- ment (if equipped)
Type A
1. Using a flat-blade screwdriver, gently
pry the mirror from the assembly. 2. Remove the scalp from the housing by
pressing the 3 hooks.
OTD079043
OTD079044
OTD079045
OTD079046
OED079071
ED(FL) ENG 7.QXP 10/28/2010 6:29 PM Page 72

773
Maintenance
3. Unscrew the bolt and then remove thelens from the housing.
4. Remove the bulb from the socket.
5. Insert a new bulb into the socket.
6. Reinstall the assembly in the reverse order of removal.
Type B
1. Remove the light assembly from thevehicle by pushing the lens forward
and pulling the assembly out.
2. Disconnect the bulb electrical connec- tor.
3. Separate the socket and the lens parts by turning the socket counter clock-
wise until the tabs on the socket align
with the slots on the lens part. 4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens part.
7. Connect the bulb electrical connector.
8. Reinstall the light assembly to the body of the vehicle.
OTD079047
OTD079048
OHD076036
ED(FL) ENG 7.QXP 10/28/2010 6:29 PM Page 73

Maintenance
74
7
Rear combination light bulb replacement
(1) Rear fog light (if equipped)
(2) Rear turn signal light
(3) Back-up light(4) Stop and tail light
(5) Tail lightType A / Type B
1. Open the tailgate.
2. Remove the service cover by turning
the plastic screw counterclockwise
and removing the cover.
Type A
Type B
OED070052/OED078058A/OED079058
Type C
OED076053
ED(FL) ENG 7.QXP 10/28/2010 6:29 PM Page 74

775
Maintenance
3. Loosen the light assembly retainingnut.
4. Remove the rear combination light assembly from the body of the vehicle. 5. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly. 6. Remove the bulb from the socket by
pressing it in and rotating it until the
tabs on the bulb align with the slots in
the socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
8. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
9. Reinstall the light assembly to the body of the vehicle.
10. Tighten the screws.
11. Reinstall the service cover.
OED070107
OED070108
OED070110OED070109
ED(FL) ENG 7.QXP 10/28/2010 6:30 PM Page 75

Maintenance
76
7
Ty p e C
1. Open the tailgate.
2. Loosen the light assembly retaining
screws with a cross-tip screwdriver.
3. Remove the rear combination light assembly from the body of the vehicle. 4. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly. 5. Remove the bulb from the socket by
pressing it in and rotating it until the
tabs on the bulb align with the slots in
the socket. Pull the bulb out of the
socket.
6. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
8. Reinstall the light assembly to the body of the vehicle.
9. Tighten the screws.
OED076063
OED070061
OED076059
OED070060
ED(FL) ENG 7.QXP 10/28/2010 6:30 PM Page 76