2011 JEEP GRAND CHEROKEE parking brake

NOTE:
Broken, muddy, or obstructed headlights
and taillights of vehicles in the field of view
will cause headlights to remain on longer
(closer to the vehicle). Also, dirt, film, and
other obstructions (sticker, toll box, etc.) on
the windshield or camera lens will cause the
system to function improperly.
Daytime Running Lights —
If Equipped
The Daytime Running Lights (low intensity)
come on whenever the engine is running, and
the transmission is not in the PARK position.
The lights will remain on until the ignition is
switched to the OFF or ACC position or the
parking brake is engaged. The headlight
switch must be used for normal nighttime driv-
ing.
Disabling the Daytime Running Lights
To disable the Daytime Running Lights open
the hood and located the Power Distribution
Center (PDC), located on the right side of the
engine compartment.Open the PDC by pulling outward on the lock-
ing tabs (one on each side) and pulling upward
on the cover.Remove the left and right Daytime Running
Lamp relays and reinstall the PDC cover.
Automatic Headlight Leveling — HID
Headlights Only
This feature prevents the headlights from inter-
fering with the vision of oncoming drivers.
Headlight leveling automatically adjusts the
height of the headlight beam in reaction to
changes in vehicle pitch.
PDC Location
Locking Tab
Daytime Running Light Relays
108

Adaptive Cruise Control (ACC)
Operation
The speed control buttons (located on the right
side of the steering wheel) operates the ACC
system.NOTE:
Any chassis/suspension modifications to
the vehicle will effect the performance of the
Adaptive Cruise Control.
Activating Adaptive Cruise Control
(ACC)
You can only activate ACC if the vehicle speed
is above 25 mph (40 km/h).
When the system is turned on and in the READY
state, the Electronic Vehicle Information Center
(EVIC) displays “Adaptive Cruise Ready.”
When the system is OFF, the EVIC displays
“Adaptive Cruise Control Off.”
NOTE:
You cannot enable ACC under the following
conditions:
•
When in Four-Wheel Drive Low.
• When you apply the brakes.
• When the parking brake is set.
• When the automatic transmission is in
PARK, REVERSE or NEUTRAL.
• When pushing the RES + button without a
previously set speed in memory.
To ActivatePush and release the ON/OFF button. The ACC
menu in the EVIC displays “Adaptive Cruise
Ready.”
To turn the system OFF, push and release the
ON/OFF button again. At this time, the system
will turn off and the EVIC will display “Adaptive
Cruise Control Off.”
1 — DISTANCE SETTING
2 — RES +
3 — SET -
4 — CANCEL
5 — ON/OFF
6 — MODE
Adaptive Cruise Control Ready
120

13. Seat Belt Reminder LightWhen the ignition switch is first turned
to ON/RUN, this light will turn on for
four to eight seconds as a bulb check.
During the bulb check, if the driver or
front passenger’s seat belt is unbuckled, a
chime will sound. After the bulb check or when
driving, if the driver or front passenger seat belt
remains unbuckled, the Seat Belt Indicator
Light will flash or remain on continuously. Refer
to “Occupant Restraints” in “Things To Know
Before Starting Your Vehicle” for further infor-
mation.
14. Brake Warning Light This light monitors various brake
functions, including brake fluid
level and parking brake applica-
tion. If the brake light turns on, it
may indicate that the parking
brake is applied, that the brake
fluid level is low, or that there is a problem with
the anti-lock brake system reservoir.
If the light remains on when the parking brake
has been disengaged, and the fluid level is at
the full mark on the master cylinder reservoir, it
indicates a possible brake hydraulic system malfunction or that a problem with the Brake
Booster has been detected by the Anti-Lock
Brake System (ABS) / Electronic Stability Pro-
gram (ESP) system. In this case, the light will
remain on until the condition has been cor-
rected. If the problem is related to the brake
booster, the ABS pump will run when applying
the brake and a brake pedal pulsation may be
felt during each stop.
The dual brake system provides a reserve
braking capacity in the event of a failure to a
portion of the hydraulic system. A leak in either
half of the dual brake system is indicated by the
Brake Warning Light, which will turn on when
the brake fluid level in the master cylinder has
dropped below a specified level.
The light will remain on until the cause is
corrected.
NOTE:
The light may flash momentarily during
sharp cornering maneuvers, which change
fluid level conditions. The vehicle should
have service performed, and the brake fluid
level checked.
If brake failure is indicated, immediate repair is
necessary.
WARNING!
Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may
have failed. It will take longer to stop the
vehicle. You could have a collision. Have the
vehicle checked immediately.
Vehicles equipped with the Anti-Lock Brake
System (ABS), are also equipped with Elec-
tronic Brake Force Distribution (EBD). In the
event of an EBD failure, the Brake Warning
Light will turn on along with the ABS Light.
Immediate repair to the ABS system is re-
quired.
Operation of the Brake Warning Light can be
checked by turning the ignition switch from the
OFF position to the ON/RUN position. The light
should illuminate for approximately two sec-
onds. The light should then turn off unless the
parking brake is applied or a brake fault is
detected. If the light does not illuminate, have
the light inspected by an authorized dealer.
161

The light also will turn on when the parking
brake is applied with the ignition switch in the
ON/RUN position.
NOTE:
This light shows only that the parking brake
is applied. It does not show the degree of
brake application.
15. Anti-Lock Brake (ABS) LightThis light monitors the Anti-Lock
Brake System (ABS). The light will
turn on when the ignition switch is
turned to the ON/RUN position and
may stay on for as long as four
seconds.
If the ABS light remains on or turns on while
driving, it indicates that the Anti-Lock portion of
the brake system is not functioning and that
service is required. However, the conventional
brake system will continue to operate normally
if the BRAKE warning light is not on.
If the ABS light is on, the brake system should
be serviced as soon as possible to restore the
benefits of Anti-Lock brakes. If the ABS light
does not turn on when the ignition switch is turned to the ON/RUN position, have the light
inspected by an authorized dealer.
16. 4 LOW
This light alerts the driver that the
vehicle is in the four-wheel drive
LOW mode. The front and rear
driveshafts are mechanically
locked together forcing the front
and rear wheels to rotate at the
same speed. Low range provides a greater
gear reduction ratio to provide increased
torque at the wheels.
For further information on four-wheel drive op-
eration and proper use, refer to “Four-Wheel
Drive Operation — If Equipped” in “Starting
And Operating”.
17. Speedometer
Indicates vehicle speed.
18. Fuel Door Reminder The fuel pump symbol points to the
side of the vehicle where the fuel
door is located. 19. Fuel Gauge
The pointer shows the level of fuel in the fuel
tank when the ignition switch is in the ON/RUN
position.
20. Electronic Vehicle Information Center
(EVIC) White Telltale Area
This area will display the EVIC reconfigurable
white telltales. For further information refer to
“Electronic vehicle Information Center (EVIC)”.
21. Electronic Vehicle Information Center
(EVIC) Amber Telltale Area
This area will display the EVIC reconfigurable
amber caution telltales. For further information
refer to “Electronic vehicle Information Center
(EVIC)”.
22. Electronic Vehicle Information Center
(EVIC) Red Telltale Area
This area will display the EVIC reconfigurable
red telltales. For further information refer to
“Electronic vehicle Information Center (EVIC)”.
162

•After Driving Off-Road ..................... 220
• POWER STEERING ......................... 220
• 3.6L Engine and 3.0L Diesel Engine ............. 220
• 5.7L Engine ........................... 221
• Power Steering Fluid Check .................. 221
• MULTI-DISPLACEMENT SYSTEM (MDS) (IF EQUIPPED) —
5.7L ENGINE ONLY ......................... 222
• PARKING BRAKE .......................... 222
• ELECTRONIC BRAKE CONTROL SYSTEM ........... 223
• Anti-Lock Brake System (ABS) ................ 223
• Traction Control System (TCS) ................ 224
• Brake Assist System (BAS) .................. 224
• Electronic Roll Mitigation (ERM) ............... 224
• Electronic Stability Control (ESC) .............. 225
• Trailer Sway Control (TSC) .................. 226
• Hill Start Assist (HSA) ..................... 227
• Ready Alert Braking ...................... 228
• Rain Brake Support ....................... 228
• Hill Descent Control (HDC) — Four-Wheel Drive Models
With MP3023 Two-Speed Transfer Case Only ........ 228
• ESC Activation/Malfunction Indicator Light and ESC OFF
Indicator Light .......................... 229
197

CAUTION!(Continued)
• Do not shift from REVERSE, PARK, or
NEUTRAL into any forward gear when the
engine is above idle speed.
• Before shifting into any gear, make sure
your foot is firmly on the brake pedal.
WARNING!
It is dangerous to move the shift lever out of
PARK or NEUTRAL if the engine speed is
higher than idle speed. If your foot is not firmly
on the brake pedal, the vehicle could acceler-
ate quickly forward or in reverse. You could
lose control of the vehicle and hit someone or
something. Only shift into gear when the
engine is idling normally and when your foot is
firmly on the brake pedal.
Key Ignition Park InterlockThis vehicle is equipped with a Key Ignition
Park Interlock which requires the shift lever to
be placed in PARK prior to turning the ignition
switch to the LOCK position. The key fob can
only be removed from the ignition switch when the ignition switch is in the LOCK position and
once removed the shift lever is locked in PARK.
Brake/Transmission Shift Interlock
System
This vehicle is equipped with a Brake Transmis-
sion Shift Interlock System (BTSI) that holds the
shift lever in the PARK position when the igni-
tion switch is in the LOCK position. To move the
shift lever out of the PARK position, the ignition
switch must be turned to the ON or START
position (engine running or not) and the brake
pedal must be pressed.
Brake/Transmission Interlock
Manual Override
Your vehicle may be equipped with a shift lock
manual override. The manual override may be
used in the event that the shift lever should fail
to move from PARK with the ignition switch in
the ON position and the brake pedal pressed.
To operate the shift lock manual override, per-
form the following steps:
1. Turn the ignition switch to the ON position
without starting the engine.
2. Firmly set the parking brake.
3. Remove the rubber liner from the cupholder
(located next to the shifter on the center con-
sole).
4. Using a flat-bladed screwdriver, carefully
remove the shift lock manual override cover,
which is located on the bottom of the cup-
holder.
5. Press and maintain firm pressure on the
brake pedal.
6. Using the screwdriver, reach into the manual
override opening. Press and hold the shift lock
lever down.
7. Move the shift lever into the NEUTRAL posi-
tion.
8. The vehicle may then be started in NEU-
TRAL.
Have your vehicle inspected by your local
authorized dealer if the shift lock manual over-
ride has been used.
205

Five-Speed Automatic TransmissionThe electronically-controlled transmission pro-
vides a precise shift schedule. The transmis-
sion electronics are self-calibrating; therefore,
the first few shifts on a new vehicle may be
somewhat abrupt. This is a normal condition,
and precision shifts will develop within a few
hundred miles/kilometers.
Gear Ranges
NOTE:
After selecting any gear range, wait a mo-
ment to allow the selected gear to engage
before accelerating. This is especially im-
portant when the engine is cold. If there is a
need to restart the engine, be sure to turn
the ignition switch to the LOCK position
before restarting. Transmission gear en-
gagement may be delayed after restarting
the engine if the ignition switch is not turned
to the LOCK position first.
PARK
This range supplements the parking brake by
locking the transmission. The engine can be
started in this range. Never use PARK while the
vehicle is in motion. Apply the parking brakewhen leaving the vehicle in this range. Always
apply the parking brake first, then place the
shift lever into the PARK position.
WARNING!
•
Never use the PARK position as a substi-
tute for the parking brake. Always apply the
parking brake fully when parked to guard
against vehicle movement and possible
injury or damage.
• It is dangerous to move the shift lever out of
PARK or NEUTRAL if the engine speed is
higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickly forward or in reverse.
You could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and
when your right foot is firmly on the brake
pedal.
REVERSE
This range is for moving the vehicle backward.
Use only after the vehicle has come to a
complete stop. NEUTRAL
This range is used when vehicle is standing for
prolonged periods with engine running. Engine
may be started in this range. Set the parking
brake if you must leave the vehicle.
NOTE:
Towing the vehicle, coasting, or driving for
any other reason with the shift lever in
NEUTRAL can result in severe transmission
damage. Refer to “Recreational Towing” in
“Starting and Operating” and “Towing a Dis-
abled Vehicle” in “What To Do In Emergen-
cies” for further information.
DRIVE
This range should be selected only when the
vehicle is at a complete stop and the brakes
are firmly applied. The transmission automati-
cally upshifts through fifth gear. The DRIVE
position provides optimum driving characteris-
tics under all normal operating conditions.
Electronic Range Select (ERS) Operation
The Electronic Range Select (ERS) shift control
allows you to move the shift lever left (-) or right
(+) when the shift lever is in the DRIVE position,
allowing you to limit the highest available gear.
206

When additional traction is required, the 4WD
LOW position can be used to lock the front and
rear driveshafts together and force the front
and rear wheels to rotate at the same speed.
The 4WD LOW position is intended for loose,
slippery road surfaces only. Driving in the 4WD
LOW position on dry, hard-surfaced roads may
cause increased tire wear and damage to
driveline components.
When operating your vehicle in 4WD LOW, the
engine speed is approximately three times that
of the 4WD HI position at a given road speed.
Take care not to overspeed the engine and do
not exceed 25 mph (40 km/h).
Proper operation of four-wheel drive vehicles
depends on tires of equal size, type, and
circumference on each wheel. Any difference
will adversely affect shifting and cause damage
to the transfer case.
Because four-wheel drive provides improved
traction, there is a tendency to exceed safe
turning and stopping speeds. Do not go faster
than road conditions permit.WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in
the N (Neutral) position without first fully en-
gaging the parking brake. The transfer case N
(Neutral) position disengages both the front
and rear driveshafts from the powertrain and
will allow the vehicle to move regardless of the
transmission position. The parking brake
should always be applied when the driver is
not in the vehicle.
Shift Positions
For additional information on the appropriate
use of each transfer case mode position, see
the information below:
4WD AUTO
This range is used on surfaces such as ice,
snow, gravel, sand, and dry hard pavement.NOTE:
Refer to “Selec-Terrain
– If Equipped” in
“Starting and Operating” for further infor-
mation on the various positions and their
intended usages.
NEUTRAL
This range disengages both the front and rear
driveshafts from the powertrain. It is to be used
for flat towing behind another vehicle. Refer to
“Recreational Towing” in “Starting and Operat-
ing” for further information.
4WD LOW
This range is for low speed four-wheel drive. It
locks the front and rear driveshafts together
and forces the front and rear wheels to rotate at
the same speed. It provides additional traction
and maximum pulling power for loose, slippery
road surfaces only. Do not exceed 25 mph
(40 km/h).
NOTE:
Refer to “Selec-Terrain – If Equipped” for
further information on the various positions
and their intended usages.
211