2011 INFINITI QX56 ground

FUEL INJECTOREC-499
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK ECM GROUND CIRCUIT
Check the continuity between ECM harness connector and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK FUEL INJECTOR
Refer to EC-499, "
Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> Replace malfunctioning fuel injector. Refer to EM-49, "
Removal and Installation".
Component InspectionINFOID:0000000006218004
1.CHECK FUEL INJECTOR
1. Turn ignition switch OFF.
2. Disconnect fuel injector harness connector.
3. Check the resistance between fuel injector terminals as per the following.
Cylinder +
−
Continuity
Fuel injector ECM
Connector Terminal Connector Terminal
1F123 1
F110 101
Existed
2108
2F124 1
F 111 7
24
3F125 1
F 111 6
23
4F126 1
F110 107
2104
5F127 1
F 111 2
29
6F128 1
F110 102
2109
7F129 1
F110 106
2103
8F130 1
F 111 1
28
+ −Continuity
ECM
Connector Terminal F 111 5 Ground Exsisted
E80 11 4
11 5
Revision: 2010 May2011 QX56

HIGH PRESSURE FUEL PUMPEC-501
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
HIGH PRESSURE FUEL PUMP
Component Function CheckINFOID:0000000006218005
1.CHECK HIGH PRESSURE FUEL PUMP FUNCTION
WITH CONSULT-III
1. Start engine.
2. Check “FUEL PRES SEN V” in “D ATA MONITOR” mode with CONSULT-III.
WITHOUT CONSULT-III
1. Start engine.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to EC-501, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006218006
1.CHECK HIGH PRESSURE FUEL PUMP SOLENOID CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector and high pressure fuel pump harness connector.
3. Check the continuity between ECM harness connector and high pressure fuel pump harness connector.
Monitor Item Condition Values/Status
FUEL PRES SEN V Engine speed: Idle 980 – 1,200 mV
Engine speed: Revving engine from idle to 4,000 rpm
quickly
1,100 – 2,900 mV
ECM
Condition Voltage
+ −
Connector Terminal Connector Terminal
F110 105 E80 175 [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
JPBIA3340ZZ
JPBIA3341ZZ
+
−
Continuity
ECM High pressure fuel pump
Connector Terminal Connector Terminal
F110 105
F24 1
Existed
11 0 2
Revision: 2010 May2011 QX56

EC-502
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
HIGH PRESSURE FUEL PUMP
4. Also check harness for short to ground and to power.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK HIGH PRESSURE
FUEL PUMP SOLENOID
Refer to EC-502, "
Component Inspection".
Is inspection result normal?
YES >> GO TO 3.
NO >> Replace high pressure fuel pump. Refer to EM-43, "
Removal and Installation".
3.CHECK HIGH PRESSURE FUEL PUMP INSTALLATION CONDITION
1. Turn ignition switch OFF.
2. Check that the high pressure fuel pump is installed with no backlash and looseness.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK CAMSHAFT
1. Remove camshaft. Refer to EM-75, "
Removal and Installation".
2. Check camshaft. Refer to EM-77, "
Inspection".
Is inspection result normal?
YES >> INSPECTION END
NO >> Replace camshaft. Refer to EM-75, "
Removal and Installation".
Component InspectionINFOID:0000000006218007
1.CHECK HIGH PRESSURE FUEL PUMP SOLENOID
1. Turn ignition switch OFF.
2. Disconnect high pressure fuel pump harness connector.
3. Check the resistance between high pressure fuel pump connector terminals as per the following.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace high pressure fuel pump. Refer to EM-43, "
Removal and Installation".
+−
Condition Resistance
High pressure fuel pump
Te r m i n a l
1 2 Temperature 20 – 30 °C (68 – 86 °F) 9 – 11 Ω
Revision: 2010 May2011 QX56

EC-504
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
ICC BRAKE SWITCH
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 3.
3.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Disconnect ICC brake switch harness connector.
3. Turn ignition switch ON.
4. Check the voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 4.
4.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT-II
Check the voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following.
 Fuse block (J/B) connector E103
 10 A fuse (No. 3)
 Harness for open or short between ICC brake switch and fuse
>> Repair open circuit or short to ground in harness or connectors.
6.CHECK ICC BRAKE SWITCH
Refer to EC-445, "
Component Inspection (ICC Brake Switch)".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Replace ICC brake switch. Refer to BR-20, "
Removal and Installation".
7.CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between ICC brake s witch harness connector and ECM harness connector.
ECM
Condition Voltage (V)
Connector +–
Te r m i n a l Te r m i n a l
E80 147
(ICC brake switch signal) 175 Brake pedalSlightly depressed Approx. 0
Fully released Battery voltage
ICC brake switch
Ground Voltage
Connector Terminal
E68 2 Ground Battery voltage
ICC brake switch Ground Voltage
Connector Terminal
E68 1 Ground Battery voltage
Revision: 2010 May2011 QX56

ICC BRAKE SWITCHEC-505
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 9.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the following.
 Harness for open or short between ICC brake switch and ECM
 Loose or poor connection for each connector and harness
>> Repair open circuit, short to ground or short to power in harness or connectors.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
Component Inspection (ICC Brake Switch)INFOID:0000000006218010
1.CHECK ICC BRAKE SWITCH-I
1. Turn ignition switch OFF.
2. Disconnect ICC brake switch harness connector.
3. Check the continuity between ICC brake switch terminals under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK ICC BRAKE SWITCH-II
1. Adjust ICC brake switch installation. Refer to BR-21, "
Inspection and Adjustment".
2. Check the continuity between ICC brake switch terminals under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace ICC brake switch. Refer to BR-20, "
Removal and Installation".
ICC brake switch ECM
Continuity
Connector Terminal Connector Terminal
E68 2 E80 147 Existed
Terminals Condition Continuity
1 and 2 Brake pedal Fully released Existed
Slightly depressed Not existed
Terminals Condition Continuity
1 and 2 Brake pedal Fully released Existed
Slightly depressed Not existed
Revision: 2010 May2011 QX56

IGNITION SIGNALEC-507
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Is the inspection result normal?
YES >> GO TO 2.
NO >> Go to
EC-168, "
Diagnosis Procedure".
2.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II
1. Turn ignition switch OFF.
2. Disconnect condenser harness connector.
3. Turn ignition switch ON.
4. Check the voltage between condenser harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-III
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector E7.
3. Check the continuity between IPDM E/R harness connector and condenser harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> Go to EC-168, "Diagnosis Procedure".
NO >> GO TO 4.
4.DETECT MALFUNCTIONING PART
Check the following.
 Harness for open or short between IPDM E/R and condenser
 Loose or poor connection for each connector and harness
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Check the continuity between condenser harness connector and ground.
3. Also check harness for short to power.
Is the inspection result normal?
ECM
Vo l ta g e
Connector +–
Terminal Terminal
E80 171
175 Battery voltage
172
Condenser Ground Voltage
Connector Terminal
F8 1 Ground Battery voltage
IPDM E/R Condenser Continuity
Connector Terminal Connector Terminal
E15 61 F8 1 Existed
Condenser Ground Continuity
Connector Terminal
F8 2 Ground Existed
Revision: 2010 May2011 QX56

EC-508
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
IGNITION SIGNAL
YES >> GO TO 6.
NO >> Repair open circuit or short to power in harness or connectors.
6.CHECK CONDENSER
Refer to EC-510, "
Component Inspection (Condenser)"
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace condenser.
7.CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IV
1. Reconnect all harness connectors disconnected.
2. Disconnect ignition coil harness connector.
3. Turn ignition switch ON.
4. Check the voltage between ignition coil harness connector and ground.
Is the inspection result normal?
YES >> GO TO 9.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the following.
 Harness connector F22 and E46
 Harness for open or short between ignition coil and harness connector F22
>> Repair or replace harness or connectors.
9.CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Check the continuity between ignition coil harness connector and ground.
3. Also check harness for short to power.
Is the inspection result normal?
Ignition coil Ground Voltage
Cylinder Connector Terminal
1F75 3
Ground Battery voltage
2F76 3
3F77 3
4F78 3
5F79 3
6F80 3
7F81 3
8F82 3
Ignition coil
Ground Continuity
Cylinder Connector Terminal
1F75 2
Ground Existed
2F76 2
3F77 2
4F78 2
5F79 2
6F80 2
7F81 2
8F82 2
Revision: 2010 May2011 QX56

IGNITION SIGNALEC-509
< DTC/CIRCUIT DIAGNOSIS > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
YES >> GO TO 10.
NO >> Repair open circuit or short to power in harness or connectors.
10.CHECK IGNITION COIL OUTPUT SI
GNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check the continuity between ignition coil harness connector and ECM harness connector.
3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
11 .CHECK IGNITION COIL WITH POWER TRANSISTOR
Refer to EC-509, "
Component Inspection (Ignition Coil with Power Transistor)".
Is the inspection result normal?
YES >> GO TO 12.
NO >> Replace malfunctioning ignition coil with power transistor.
12.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
Component Inspection (Ignition Coil with Power Transistor)INFOID:0000000006218013
1.CHECK IGNITION COIL WITH POWER TRANSISTOR-I
1. Turn ignition switch OFF.
2. Disconnect ignition coil harness connector.
3. Check resistance between ignition coil terminals as per the following.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace malfunctioning ignition coil with power transistor.
2.CHECK IGNITION COIL WITH POWER TRANSISTOR-II
CAUTION:
Perform the following procedure in a place with no combustible objects and good ventilation.
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
Ignition coil ECM Continuity
Cylinder Connector Terminal Connector Terminal
1F75 1
F 11112
Existed
2F76 1 13
3F77 1 14
4F78 1 15
5F79 1 17
6F80 1 18
7F81 1 19
8F82 1 20
Terminals Resistance [at 25
°C (77 °F)]
1 and 2 Except 0 or ∞ Ω
1 and 3 Except 0 Ω
2 and 3
Revision: 2010 May2011 QX56