2011 INFINITI QX56 ECU

SEC-50
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to c onfirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 7.
YES (Symptom remains)>>GO TO 6.
NO >> INSPECTION END
Revision: 2010 May2011 QX56

HORN FUNCTIONSEC-143
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
HORN FUNCTION
Component Function CheckINFOID:0000000006226308
1.CHECK FUNCTION 1
1. Disconnect vehicle security horn relay.
2. Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON\
-
SULT-III.
3. Check the horn operation.
Is the operation normal?
YES >> GO TO 2.
NO >> Go to SEC-143, "
DiagnosisProcedure".
2.CHECK FUNCTION 2
1. Reconnect vehicle security horn relay.
2. Disconnect horn relay.
3. Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON\
-
SULT-III.
4. Check the horn operation.
Is the operation normal?
YES >> INSPECTION END
NO >> Go to SEC-143, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006226309
1.INSPECTION START
Perform inspection in accordance with procedure that confirms malfunction.
Which procedure confirms malfunction?
Component Function Check 1>>GO TO 2.
Component Function Check 2>>GO TO 4.
2.CHECK HORN FUNCTION
Check that horns function properly using horn switch.
Do horns sound?
YES >> GO TO 3.
NO >> Check horn circuit. Refer to HRN-3, "
Wiring Diagram".
3.CHECK HORN CONTROL CIRCUIT
1. Disconnect horn relay.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R har ness connector and horn relay harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Test item Description
VEHICLE SECURITY HORN ON Horn Sounds (for 0.5 sec)
Test item Description
VEHICLE SECURITY HORN ON Vehicle security horn Sounds (for 0.5 sec)
IPDM E/R Horn relay Continuity
Connector Terminal Connector Terminal
E13 34 E5 1 Existed
Revision: 2010 May2011 QX56

SEC-144
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation".
NO >> Repair or replace harness.
4.CHECK VEHICLE SECURITY HORN RELAY POWER SUPPLY
1. Disconnect vehicle security horn relay.
2. Check voltage between vehicle security horn relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO-1 >> Check 10 A fuse [No. 36 located in the fuse block (J/B)].
NO-2 >> Check harness for open or short between vehicle security horn relay and fuse.
5.CHECK VEHICLE SECURITY HORN CONTROL CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connec tor and vehicle security horn relay harness connec-
tor.
3. Check continuity between IP DM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK VEHICLE SECURITY HORN CIRCUIT
1. Disconnect vehicle security horn connector.
2. Check continuity between vehicle security horn relay harness connector and vehicle security horn har-
ness connector.
3. Check continuity between vehicle secu rity horn relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
IPDM E/R GroundContinuity
Connector Terminal
E13 34 Not existed
(+) (–)Voltage (V)
(Approx.)
Vehicle security horn relay
Connector Terminal E124 1 Ground Battery voltage
IPDM E/R Vehicle se curity horn relay
Continuity
Connector Terminal Connector Terminal
E1334E1243Existed
IPDM E/R GroundContinuity
Connector Terminal
E13 34 Not existed
Vehicle security horn re lay Vehicle security horn
Continuity
Connector Terminal Connector Terminal
E124 2 E125 1 Existed
Vehicle security horn relay GroundContinuity
Connector Terminal
E124 2 Not existed
Revision: 2010 May2011 QX56

HORN FUNCTIONSEC-145
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
NO >> Repair or replace harness.
7.CHECK VEHICLE SECURITY HORN RELAY
Refer to SEC-145, "
Component Inspection".
Is the inspection result normal?
YES >> Replace vehicle security horn.
NO >> Replace vehicle security horn relay.
Component InspectionINFOID:0000000006248777
1.CHECK VEHICLE SECURITY HORN RELAY
1. Turn ignition switch OFF.
2. Disconnect vehicle security horn relay.
3. Check voltage between vehicle security horn relay terminal and ground under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace vehicle security horn relay.
(+)
(− ) Condition Voltage (V)
(Approx.)
Vehicle security horn relay
Te r m i n a l
2Ground 12 V direct current supply between terminals 1 and 3 12
No current supply 0
Revision: 2010 May2011 QX56

SEC-146
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Component Function CheckINFOID:0000000006226312
1.CHECK FUNCTION
1. Perform “THEFT IND” in “ACTIVE TEST” m ode of “IMMU” of “BCM” using CONSULT-III.
2. Check security indicator lamp operation.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to SEC-146, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006226313
1.CHECK SECURITY INDICATOR LA MP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO-1 >> Check 10 A fuse [No. 11, located in the fuse block (J/B)].
NO-2 >> Check harness for open or short between combination meter and fuse.
2.CHECK SECURITY INDI CATOR LAMP SIGNAL
1. Connect combination meter connector.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.REPLACE BCM
1. Replace BCM. Refer to BCS-81, "
Removal and Installation".
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.
For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.
>> INSPECTION END
4.CHECK SECURITY INDI CATOR LAMP CIRCUIT
1. Disconnect combination meter connector.
2. Check continuity between combination meter harness connector and BCM harness connector.
Te s t i t e m D e s c r i p t i o n
THEFT IND ON
Security indicator lamp Illuminates
OFF Does not illuminate
(+) (–)Voltage (V)
(Approx.)
Combination meter
Connector Terminal M34 1 Ground Battery voltage
(+) (–)Voltage (V)
(Approx.)
BCM
Connector Terminal
M68 23 Ground Battery voltage
Revision: 2010 May2011 QX56

SECURITY INDICATOR LAMPSEC-147
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
3. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-85, "Removal and Installation".
NO >> Repair or replace harness.
Combination meter BCM Continuity
Connector Terminal Connector Terminal
M34 28 M68 23 Existed
Combination meter GroundContinuity
Connector Terminal
M34 28 Not existed
Revision: 2010 May2011 QX56

SEC-148
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
ENGINE DOES NOT START WHEN INTELLI
GENT KEY IS INSIDE OF VEHICLE
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
DescriptionINFOID:0000000006226323
Engine does not start when push-button ignition swit ch is pressed while carrying Intelligent Key.
NOTE:
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 The engine start function, door lock function, power di stribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regar ding control. The vehicle security function can oper-
ate only when the door lock and power dist ribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
 “ENGINE START BY I-KEY” in “WORK SUPPOR T” is ON when setting on CONSULT-III.
 Intelligent Key is not inserted in key slot.
 One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis ProcedureINFOID:0000000006226324
1.PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” on Work Support in “INTELLIGENT KEY”.
Refer to SEC-22, "
INTELLIGENT KEY : CONSULT-III F unction (BCM - INTELLIGENT KEY)".
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?
YES >> Refer to BCS-57, "DTCIndex".
NO >> GO TO 3.
3.CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to PCS-71, "
ComponentFunctionCheck".
Is the operation normal?
YES >> GO TO 4.
NO >> Repair or replace malfunctioning parts.
4.CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> GO TO 1.
Revision: 2010 May2011 QX56

SEC-150
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP DO
ES NOT TURN ON OR BLINK
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
DescriptionINFOID:0000000006226327
Security indicator lamp does not blink when i gnition switch is in a position other than ON
NOTE:
 Before performing the diagnosis, check “Work Flow”. Refer to SEC-48, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
Conditions of Vehicle (Operating Conditions)
Ignition switch is not in the ON position.
Diagnosis ProcedureINFOID:0000000006226328
1.CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to SEC-146, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-40, "Intermittent Incident".
NO >> GO TO 1.
Revision: 2010 May2011 QX56