2011 INFINITI QX56 engine

EC-44
< SYSTEM DESCRIPTION >[VK56VD]
SYSTEM
VVEL SYSTEM : System Diagram
INFOID:0000000006217709
VVEL SYSTEM : System DescriptionINFOID:0000000006217710
INPUT/OUTPUT SIGNAL CHART
SYSTEM DESCRIPTION
JSBIA0539GB
Sensor Input signal to ECM ECM function Actuator
Camshaft position sensor
Crankshaft position sensor Engine speed and piston position
VVEL controlVVEL control module
↓
VVEL actuator motor assem-
bly
Accelerator pedal position sensor Accelerator pedal position
VVEL control shaft
position sensor
↓
VVEL control module Control shaft actual angle
1. VVEL control shaft position
sensor 2. Drive shaft 3. Link A
4. Eccentric cam 5. Output cam 6. Valve lifter
7. Intake valve 8. Intake camshaft sprocket 9. Control shaft
10. Ball screw shaft 11. Ball screw nu t 12. VVEL actuator motor assembly
13. Rocker arm 14. Link B
JSBIA0463ZZ
Revision: 2010 May2011 QX56

SYSTEMEC-45
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
VVEL (Variable Valve Event & Lift) is a system that
controls valve event and valve lift continuously.
ECM decides the target valve lift according to the driving condition and sends the command signal to the
VVEL control module via ENG communication line.
VA LV E L I F T O P E R AT I O N
Rotational movement of the drive shaft equipped with eccentric cam
is transmitted to output cam via the rocker arm and two kinds of links
to depress the intake valve.
VA R I A B L E O P E R AT I O N
VVEL control module controls the ro tation of the control shaft using
the VVEL actuator motor assembly and changes the movement of
the output cam by shifting the link supporting point. As a result, valve
lift changes continuously to improve engine output and response.
EVAPORATIVE EMISSION SYSTEM
EVAPORATIVE EMISSION SYSTEM : System DiagramINFOID:0000000006256911
EVAPORATIVE EMISSION SYSTEM : System DescriptionINFOID:0000000006256912
INPUT/OUTPUT SIGNAL CHART
1. Link B
2. Output cam
3. Eccentric cam
4. Drive shaft
5. Link A
6. Rocker arm
JSBIA0464ZZ
1. Link B
2. Output cam
3. Control shaft
4. Rocker arm
JSBIA0465ZZ
JSBIA0371GB
Revision: 2010 May2011 QX56

EC-46
< SYSTEM DESCRIPTION >[VK56VD]
SYSTEM
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to the ECM via the CAN communication line.
SYSTEM DESCRIPTION
The evaporative emission system is used to reduce hydr
ocarbons emitted into the atmosphere from the fuel
system. This reduction of hydrocarbons is accomplis hed by activated charcoals in the EVAP canister.
The fuel vapor in the sealed fuel tank is led into t he EVAP canister which contains activated carbon and the
vapor is stored there when the engine is not oper ating or when refueling to the fuel tank.
The vapor in the EVAP canister is purged by the air through the purge line to the intake manifold when the
engine is operating. EVAP canister purge volume contro l solenoid valve is controlled by ECM. When the
engine operates, the flow rate of vapor controlled by EVAP canister purge volume control solenoid valve is
proportionally regulated as the air flow increases.
EVAP canister purge volume control solenoid valve also shuts off the vapor purge line during decelerating and
idling.
AIR CONDITIONING CUT CONTROL
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor
Camshaft position sensor  Engine speed*
1
 Piston position
EVAP canister
purge flow controlEVAP canister purge volume
control solenoid valve
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Battery
Battery voltage*
1
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
(Mixture ratio
feedback signal)
Fuel tank temperature sensor Fuel temperature in fuel tank
EVAP control system pressure sensor Pressure in purge line
Combination meter Vehicle speed*
2
PBIB1631E
Revision: 2010 May2011 QX56

SYSTEMEC-47
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
AIR CONDITIONING CUT CONTROL : System DiagramINFOID:0000000006217713
AIR CONDITIONING CUT CONTROL : System DescriptionINFOID:0000000006217714
INPUT/OUTPUT SIGNAL CHART
*1: This signal is sent to the ECM via the CAN communication line.
*2: ECM determines the start signal status by the signals of engine speed and battery voltage.
SYSTEM DESCRIPTION
This system improves engine operation when the air conditioner is used.
Under the following conditions, the air conditioner is turned OFF.
 When the accelerator pedal is fully depressed.
 When cranking the engine.
 At high engine speeds.
 When the engine coolant temperature becomes excessively high.
 When operating power steering during low engine speed or low vehicle speed.
 When engine speed is excessively low.
 When refrigerant pressure is excessively low or high.
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
JMBIA1457GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor
Camshaft position sensor Engine speed*
2
Air conditioner cut
controlIPDM E/R
↓
A/C relay
↓
Compressor
Engine coolant temperature sensor Engine coolant temperature
Accelerator pedal position sensor Accelerator pedal position
Battery
Battery voltage*
2
Refrigerant pressure sensor Refrigerant pressure
Power steering pressure sensor Power steering operation
A/C auto amp.A/C ON signal*
1
A/C evaporator temperature*1
Target A/C evaporator temperature*1
Blower fan ON signal
Combination meter Vehicle speed*
1
Revision: 2010 May2011 QX56

EC-48
< SYSTEM DESCRIPTION >[VK56VD]
SYSTEM
AUTOMATIC SPEED CONTROL DEVI CE (ASCD) : System Diagram
INFOID:0000000006217715
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System DescriptionINFOID:0000000006217716
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM via the CAN communication line
BASIC ASCD SYSTEM
 Automatic Speed Control Device (ASCD) allows a dr iver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can be set the vehicle speed in the set speed range.
 ECM controls throttle angle of electric th rottle control actuator to regulate engine speed.
 Operation status of ASCD is indicated in combination meter.
 If any malfunction occurs in the ASCD system, it automatically deactivates the ASCD control.
Refer to EC-49, "
AUTMATIC SPEED CONTROL DEVICE (A SCD) : Switch Name and Function" for ASCD
operating instructions.
CAUTION:
Always drive vehicle in a safe manner according to traffic conditions and obey all traffic laws.
CAN COMMUNICATION
CAN COMMUNICATION : System DescriptionINFOID:0000000006217718
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication s peed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CA N communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communication Signal Chart", about CAN com-
munication for detail.
JPBIA3272GB
Sensor Input signal to ECM ECM function Actuator
ASCD steering switch ASCD steering switch operation
ASCD vehicle speed control Electric throttle control ac-
tuator
 Combination meter
ASCD brake switch
Brake pedal operation
Sto p l am p s w it ch
TCM Park/neutral position signal
Output shaft revolution signal*
Combination meter Vehicle speed signal*
Revision: 2010 May2011 QX56

EC-50
< SYSTEM DESCRIPTION >[VK56VD]
OPERATION
- Engine coolant temperature is slightly higher than
the normal operating temperature. Then CRUISE indica-
tor lamp is blinked slowly.
NOTE:
Engine coolant temperature decreases to the norma l operating temperature, CRUISE indicator lamp stop
blinking and the cruise operation is able to work.
- Malfunction for some self-diagnoses regarding ASCD s ystem. CRUISE indicator lamp is blinked quickly.
 When ASCD MAIN switch is turned to OFF during the cr uise control driving, all of ASCD operations is can-
celed and vehicle speed memory is erased.
Revision: 2010 May2011 QX56

EC-52
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
DIAGNOSIS SYSTEM (ECM)
DIAGNOSIS DESCRIPTION
DIAGNOSIS DESCRIPTION : 1st Trip Detect
ion Logic and Two Trip Detection Logic
INFOID:0000000006217722
When a malfunction is detected for the first time, 1st tr ip DTC and 1st trip Freeze Frame data are stored in the
ECM memory. The MIL will not illuminate at this stage. <1st trip>
If the same malfunction is detected again during the next drive, the DTC and Freeze Frame data are stored in
the ECM memory, and the MIL illuminates. The MIL illu minates at the same time when the DTC is stored.
<2nd trip> The “trip” in the “Two Trip Detection Logic” means a driving mode in which self-diagnosis is per-
formed during vehicle operation. Specific on board diagnos tic items will cause the ECM to illuminate or blink
the MIL, and store DTC and Freeze Frame data, even in the 1st trip, as shown below.
×: Applicable —: Not applicable
DIAGNOSIS DESCRIPTION : DT C and Freeze Frame DataINFOID:0000000006217723
DTC AND 1ST TRIP DTC
The 1st trip DTC (whose number is the same as the DT C number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously , and the 1st trip DTC did not recur, the 1st trip DTC
will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is saved in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunc tion is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are saved in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL light s up when the same malfunction occurs in two consec-
utive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd
trips, only the 1st trip DTC will continue to be stored. Fo r malfunctions that blink or light up the MIL during the
1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
For malfunctions in which 1st trip DTCs are displayed, refer to EC-98, "
DTC Index". These items are required
by legal regulations to continuous ly monitor the system/component. In addi tion, the items monitored non-con-
tinuously are also displayed on CONSULT-III.
1st trip DTC is specified in Service $07 of SAE J1979/ ISO 15031-5. 1st trip DTC detection occurs without illu-
minating the MIL and therefore does not warn the driver of a malfunction.
When a 1st trip DTC is detected, check, print out or write down and erase (1st trip) DTC and Freeze Frame
data as specified in Work Flow procedure Step 2, refer to EC-135, "
Work Flow". Then perform DTC Confirma-
tion Procedure or Component Function Check to try to duplicate the malfunction. If the malfunction is dupli-
cated, the item requires repair.
FREEZE FRAME DATA AND 1ST TRIP FREEZE FRAME DATA
The ECM records the driving conditions such as fuel system status, calculated load value, engine coolant tem-
perature, short term fuel trim, long term fuel trim, engine speed, vehicle speed, absolute throttle position, base
fuel schedule and intake air temperature at the moment a malfunction is detected.
Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data.
The data, stored together with the DTC data, are ca lled freeze frame data and displayed on CONSULT-III or
GST. The 1st trip freeze frame data can only be displayed on the CONSULT-III screen.
Items MIL DTC 1st trip DTC
1st trip 2nd trip 1st trip
displaying 2nd trip
displaying 1st trip
displaying 2nd trip
displaying
Blinking Illuminate Blinking Illuminate
Misfire (Possible three way catalyst
damage) — DTC: P0300 - P0308 is
being detected ×
——— — — ×—
Misfire (Possible three way catalyst
damage) — DTC: P0300 - P0308 is
being detected ——
×—— ×——
One trip detection diagnoses (Re-
fer to EC-98, "
DTC Index".) —
×—— ×———
Except above — — — ×— ×× —
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (ECM)EC-55
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
 The B counter will be cleared when the malfunction is
detected once regardless of the driving pattern.
 The B counter will be counted up when driving pattern B is satisfied without any malfunction.
 The MIL will turn OFF when the B counter reaches 3. (*2 in “OBD SYSTEM OPERATION CHART”)

Driving pattern C means operating vehicle as per the following:
The following conditions should be satisfied at the same time:
Engine speed: (Engine speed in the freeze frame data) ±375 rpm
Calculated load value: (Calculated load value in the freeze frame data) x (1 ±0.1) [%]
Engine coolant temperature (T) condition:
 When the freeze frame data shows lower than 70 °C (158 °F), T should be lower than 70 °C (158 °F).
 When the freeze frame data shows higher than or equal to 70 °C (158 °F), T should be higher than or equal to
70 °C (158 °F).
Example:
If the stored freeze frame data is as per the following:
Engine speed: 850 rpm, Calculated load val ue: 30%, Engine coolant temperature: 80°C (176 °F)
To be satisfied with driving pattern C, the v ehicle should run under the following conditions:
Engine speed: 475 - 1,225 rpm, Calculated load value: 27 - 33%, Engine coolant temperature: more than 70°C
(158 °F)
 The C counter will be cleared when the malfunction is detected regardless of vehicle conditions above.
 The C counter will be counted up when vehicle conditions above are satisfied without the same malfunction.
 The DTC will not be displayed after C counter reaches 80.
 The 1st trip DTC will be cleared when C counter is counted once without the same malfunction after DTC is
stored in ECM.
Relationship Between MIL, DTC, 1st Trip DTC and Driving Patterns Except For “Misfire Quality Deterioration>”, “Fuel Injection System”
Revision: 2010 May2011 QX56