2011 INFINITI QX56 rear panel

GW-24
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
8. Operate the power window switch to raise or lower the door win-dow until the glass mounting bolts can be seen.
9. Remove the rear door glass mounting bolts.
10. Raise rear door glass up and hold it with a suction lifter (A).
11. Disconnect rear door power window motor harness connector.
12. Remove rear door regulator mounting nuts.
13. Remove rear door power window motors mounting bolts.
14. Remove rear door regulator from rear door panel.
15. Securely place rear door glass down inside rear door panel.
16. Remove rear door glass run.
17. Remove rear door sash mounting bolts and screw, and then pull it up to remove.
CAUTION:
Be careful not to scratch or damage rear door glass with
rear door sash.
18. Remove rear door glass from rear door panel as shown by the figure.
: Bolt
JMKIA1789ZZ
PIIB3511J
JMKIA5272ZZ
JMKIA5273ZZ
Revision: 2010 May2011 QX56

GW-26
< REMOVAL AND INSTALLATION >
REAR REGULATOR
REAR REGULATOR
Exploded ViewINFOID:0000000006220832
Removal and InstallationINFOID:0000000006220833
REMOVAL
1. Remove rear door finisher. Refer to INT-16, "Removal and Installation".
2. Remove rear door inside seal.
3. Remove rear door outside molding. Refer to EXT-32, "
Removal and Installation".
4. Remove rear pull handle bracket mounting bolts and then remove it.
5. Disconnect rear door speaker harness connector.
6. Remove the sealing screen with a cutter tool. NOTE:
Cut the butyl-tape so that some parts of the butyl-t ape do not remain on the sealing screen, if the sealing
screen is reused.
7. Reconnect the rear door power window switch.
1. Rear door panel 2. Rear door glass run 3. Partition sash
4. Partition glass 5. Rear door glass 6. Rear door regulator
7. Rear power window motor 8. Rear door pull handle bracket 9. Rear door sealing screen
10. Grommet 11. Rear door inside seal
JMKIA5209ZZ
Revision: 2010 May2011 QX56

REAR REGULATORGW-27
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
GW
N
O P
8. Operate the power window switch to raise or lower the door win- dow until the glass mounting bolts can be seen.
9. Remove the rear door glass mounting bolts.
10. Raise rear door glass up and hold it with a suction lifter (A).
11. Disconnect rear door power window motor harness connector.
12. Remove rear door regulator mounting nuts.
13. Remove rear door power window motors mounting bolts.
14. Remove rear door regulator from rear door panel.
INSTALLATION
Install in the reverse order of removal.
Disassembly and AssemblyINFOID:0000000006220834
DISASSEMBLY
Remove rear power window motor from rear door regulator.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and AdjustmentINFOID:0000000006220835
SYSTEM INITIALIZATION
Initialize the system if any of t he following work has been done. Refer to ADP-51, "ADDITIONAL SERVICE
WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description".
Initialization
Follow the steps below after installing each component to the vehicle. Refer to ADP-51, "ADDITIONAL SER-
VICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".
FITTING INSPECTION
 Check that the glass is fit securely into the sash groove.
 Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
: Bolt
JMKIA1789ZZ
PIIB3511J
Revision: 2010 May2011 QX56

HAC-148
< REMOVAL AND INSTALLATION >[AUTOMATIC AIR CONDITIONING]
IN-VEHICLE SENSOR
IN-VEHICLE SENSOR
FRONT A/C UNIT ASSEMBLY
FRONT A/C UNIT ASSEMBLY :
Removal and InstallationINFOID:0000000006276001
REMOVAL
1. Remove instrument lower panel LH. Refer to IP-14, "Removal and Installation".
2. Remove fixing screw, and then remove in-vehicle sensor.
INSTALLATION
Install in the reverse order of removal.
REAR A/C UNIT ASSEMBLY
REAR A/C UNIT ASSEMBLY : Removal and InstallationINFOID:0000000006276002
REMOVAL
1. Remove rear A/C unit assembly. Refer to HA-47, "REAR A/C UNIT ASSEMBLY : Removal and Installa-
tion".
2. Remove the intake sensor from rear A/C unit assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Replace O-rings with new ones. Then apply the compressor oil to them when installing.
 Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
 Never rotate the bracket insertion part when removing and installing the intake sensor.
 Check for leakages when recharging refrigerant. Refer to HA-18, "
Leak Test".
Revision: 2010 May2011 QX56

DOOR MOTORHAC-153
< REMOVAL AND INSTALLATION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
MODE DOOR MOTOR
MODE DOOR MOTOR : Re moval and InstallationINFOID:0000000006276009
REMOVAL
1. Remove instrument lower panel RH. Refer to IP-14, "Removal and Installation".
2. Remove power steering control unit bracket.
3. Remove fixing screws (A), and then remove mode door motor (1).
4. Disconnect mode door motor connector.
INSTALLATION
Install in the reverse order of removal.
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR : Re moval and InstallationINFOID:0000000006276010
REMOVAL
Driver side
1. Remove automatic drive position control unit. Refer to ADP-136, "Removal and Installation".
2. Remove fixing screws (A), and then remove air door motor LH (1).
3. Disconnect air mix door motor connector.
Passenger side
1. Remove heater core. Refer to HA-44, "HEATER CORE : Removal and Installation".
2. Remove fixing screws, and then remove air mix door motor RH.
INSTALLATION
Install in the reverse order of removal.
INTAKE DOOR MOTOR
INTAKE DOOR MOTOR : Re moval and InstallationINFOID:0000000006276011
REMOVAL
1. Remove blower unit assembly. Refer to VTL-15, "Removal and Installation".
2. Remove fixing screws, and then remove intake door motor.
1. Rear A/C unit assembly 2. Rear mode door lever 2 3. Rear mode door lever 1
4. Rear mode door motor 5. Rear air mix door motor
JMIIA0790ZZ
JMIIA0788ZZ
Revision: 2010 May2011 QX56

INT-16
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded ViewINFOID:0000000006220243
Removal and InstallationINFOID:0000000006220244
CAUTION:
 When removing, always use a remover tool that is made of plastic.
 Never damage the body.
1. Rear door finisher 2. Bumper rubber 3. Door finisher cap
4. Inside handle escutcheon 5. Rear door grip cap 6. Step lamp
7. Power window switch finisher 8. Power window switch 9. Tweeter grille
10. Rear door garnish 11. Rear door tweeter 12. Rear door panel
13. Rear door inside handle 14. Rear door inside seal: Clip
: Pawl
JMJIA4423ZZ
Revision: 2010 May2011 QX56

REAR DOOR FINISHERINT-17
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
REMOVAL
1. Fully open door window.
2. Remove door finisher cap (1) using a small flat-bladed screw- driver (A) as shown by the arrow in the figure, and then remove
rear door finisher mounting bolt.
CAUTION:
Use a small flat-bladed screwdriver wrapped in tape (B).
3. Insert a remover tool (A) between rear door grip cap (1) and rear door grip to disengage rear door grip cap fixing pawls as shown
by the arrow in the figure, and then remove fixing screws.
4. Remove step lamp, and then disconnect step lamp harness connector. Refer to INL-74, "
Removal and
Installation".
5. Remove bumper rubber.
6. Insert a remover tool (A) between rear door finisher and rear door panel to disengage the clips as shown by the arrow in the
figure.
CAUTION:
Insert a remover tool into the part shown in the figure
(between the clips and the door panel).
7. Disconnect mood lamp harness connector.
8. Disconnect power window switch harness connector and clamp.
9. Disconnect lock knob cable and inside handle cable from rear inside handle.
10. Remove rear door finisher from rear door panel.
11. Remove the following parts after removing rear door finisher.  Mood lamp.
 Power window switch. Refer to PWC-74, "
Removal and Installation".
 Rear door inside handle. Refer to DLK-244, "
INSIDE HANDLE : Removal and Installation".
 Rear door tweeter. Refer to AV-218, "
Removal and Installation".
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visualy check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing rear door finish er, check that clips and pawls are secu rely fitted in body panel holes,
and press them in.
: Pawl
JMJIA4013ZZ
: Pawl
JMJIA4016ZZ
: Clip
JMJIA4017ZZ
Revision: 2010 May2011 QX56

INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE WELT
BODY SIDE WELT : Removal and InstallationINFOID:0000000006220248
CAUTION:
Never damage the body.
REMOVAL
Front body side welt
1. Remove front kicking plate inner and rear kicking plate inner. Refer to INT-20, "KICKING PLATE INNER :
Removal and Installation".
2. Remove dash side finisher. Refer to INT-18, "
DASH SIDE FINISHER : Removal and Installation".
3. Slide front seat assembly to the frontmost position.
4. Remove center pillar lower garnish. Refer to INT-22, "
CENTER PILLAR LOWER GARNISH : Removal
and Installation".
5. Remove front body side welt.
Rear body side welt
1. Remove front kicking plate inner and rear kicking plate inner. Refer to INT-20, "KICKING PLATE INNER :
Removal and Installation".
2. Slide front seat assembly to the frontmost position.
3. Remove center pillar lower garnish. Refer to INT-22, "
CENTER PILLAR LOWER GARNISH : Removal
and Installation".
4. Remove luggage side lower finisher. Refer to INT-36, "
LUGGAGE SIDE LOWER FINISHER : Removal
and Installation".
5. Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and InstallationINFOID:0000000006220249
CAUTION:
 When removing, always use a remover tool that is made of plastic.
 Never damage the body.
REMOVAL
Front kicking plate inner
Disengage front kicking plate inner fixing pawls and metal clips using
a remover tool (A) as shown by the arrow in the figure, and then
remove front kicking plate inner.
CAUTION:
Apply protective tape (B) to the body panel to protect from dam-
age.
Rear kicking plate inner
1. Disengage rear kicking plate inner fixing pawls using a re mover tool (A) as shown by the arrow in the fig-
ure, and then remove rear kicking plate inner (1).
CAUTION:
: Pawl
: Metal clip
JMJIA4021ZZ
Revision: 2010 May2011 QX56