2011 INFINITI QX56 atf

TM-182
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
CONTROL VALVE & TCM
CONTROL VALVE & TCM
Exploded ViewINFOID:0000000006226899
Removal and InstallationINFOID:0000000006226900
REMOVAL
1. Drain ATF through drain plug.
1. A/T 2. Snap ring 3. Control valve & TCM
4. Oil pan gasket 5. Oil pan 6. Clip
7. Oil pan mounting bolt 8. Overflow plug 9. Drain plug
10. Drain plug gasket 11. Magnet 12. Clip
13. Joint connector
Refer to
GI-4, "
Components" for symbols in the figure.
JSDIA1755GB
Revision: 2010 May2011 QX56

TM-184
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
CONTROL VALVE & TCM
9. Remove bolts and clip (1) from the control valve & TCM.
*: Reamer bolt
10. Remove the control valve & TCM from transmission case.
CAUTION:
When removing, be careful wi th the manual valve (1) notch
and manual plate (2) height. Remove it vertically.
11. Remove joint connector (1) from the control valve & TCM using a flat-bladed screwdriver (A).
12. Disconnect TCM connector (A). CAUTION:
Be careful not to damage connector.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Be careful not to damage connector when installing any connector.
 Never reuse joint connector.
 Apply ATF to O-ring of joint connector.
 Never reuse drain plug and drain plug gasket. In addition, install new drain plug and drain plug gas-
ket after adjustment of A/T fluid filling.
 Refer to the following when installing the control valve & TCM to transmission case.
: Vehicle front
Bolt symbol Length mm (in) Number of bolts A 43 (1.69) 3
B 40 (1.57) 2
C 54 (2.13) 6
D 50 (1.97) 2
E* 50 (1.97) 1
JPDIA1105ZZ
JPDIA0012ZZ
JSDIA1718ZZ
JSDIA1813ZZ
Revision: 2010 May2011 QX56

TM-186
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
CONTROL VALVE & TCM
Inspection and Adjustment
INFOID:0000000006226901
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
 If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to TM-175, "Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Perform decel G sensor calibration when replacing control valve & TCM. Refer to TM-92, "
Special Repair
Requirement".
SCIA5199E
Revision: 2010 May2011 QX56

PARKING COMPONENTSTM-187
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
PARKING COMPONENTS
2WD
2WD : Exploded ViewINFOID:0000000006233258
2WD : Removal and InstallationINFOID:0000000006233259
REMOVAL
1. Drain ATF through drain plug.
2. Separate propeller shaft assembly. Refer to DLN-143, "
Exploded View".
3. Support A/T assembly with a transmission jack. CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
4. Remove rear engine mounting cross member with power tool. Refer to TM-205, "
2WD : Exploded View".
5. Remove engine mounting insulator (rear). Refer to TM-205, "
2WD : Exploded View".
1. Parking actuator support 2. Parking pawl 3. Return spring
4. Pawl shaft 5. Parking gear 6. Seal ring
7. Output shaft 8. Bearing race 9. Needle bearing
10. Self-sealing bolt 11. Bracket 12. Rear extension
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JSDIA1926GB
Revision: 2010 May2011 QX56

TM-192
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
REAR OIL SEAL
REAR OIL SEAL
2WD
2WD : Exploded ViewINFOID:0000000006228060
2WD : Removal and InstallationINFOID:0000000006228061
REMOVAL
1. Remove propeller shaft assembly. Refer to
DLN-144, "Removal and Installation".
2. Remove rear oil seal (1) using a flat-bladed screwdriver (A). CAUTION:
Be careful not to scratch rear extension assembly.
INSTALLATION
Note the following and install in the reverse order of removal.
 As shown in the figure, use the drift [SST: ST33400001 (J-26082)](A) to drive rear oil seal into rear extension assembly until it is
flush.
CAUTION:
 Never reuse rear oil seal.
 Apply ATF to rear oil seal.
1. A/T 2. Rear oil seal
Refer to GI-4, "
Components" for symbols in the figure.
JSDIA1843ZZ
JPDIA0037ZZ
JPDIA0039ZZ
Revision: 2010 May2011 QX56

TM-194
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
REAR OIL SEAL
 As shown in the figure, use the drift [64 mm (2.52 in) dia. commer-
cial service tool] (A) to drive rear oil seal into adapter case assem-
bly until it is flush.
CAUTION:
 Never reuse rear oil seal.
 Apply ATF to rear oil seal.
4WD : Inspection and AdjustmentINFOID:0000000006226904
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to TM-175, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust A/T fluid level. Refer to TM-95, "Adjustment".
JPDIA0040ZZ
Revision: 2010 May2011 QX56

OUTPUT SPEED SENSORTM-195
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
OUTPUT SPEED SENSOR
2WD
2WD : Exploded ViewINFOID:0000000006228119
2WD : Removal and InstallationINFOID:0000000006228120
REMOVAL
1. Disconnect the battery cabl e from the negative terminal.
2. Drain ATF through drain plug.
3. Separate propeller shaft assembly. Refer to DLN-143, "
Exploded View".
1. A/T 2. Oil pan gasket 3. Oil pan
4. Clip 5. Oil pan mounting bolt 6. Overflow plug
7. Drain plug 8. Drain plug gasket 9. Magnet
10. Output speed sensor 11. Self-sealing bolt 12. Bracket
13. Rear extension
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-22, "Recommended Chemical Products and Sealants".
Refer to GI-4, "
Components" for symbols not described on the above.
JSDIA1925GB
Revision: 2010 May2011 QX56

TM-198
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
OUTPUT SPEED SENSOR
- Tighten rear extension assembly bolts to the specified torque.
 Refer to the followings when installing oil pan (2) (with oil pan gas-
ket) and clips (1) to transmission case.
CAUTION:
 Never reuse oil pan gasket and oil pan mounting bolts.
 Install oil pan gasket in the di rection to align hole position.
 Install it so that drain plug comes to the position as shown
in the figure.
 Be careful not to pinch harnesses.
 Completely remove all moisture, oil and ol d gasket, etc. from oil pan mounting surface.
- Tighten oil pan mounting bolts to the specified torque in numerical
order shown in the figure after temporarily tightening them. Tighten
necessary oil pan mounting bolts with specified torque.
2WD : Inspection and AdjustmentINFOID:0000000006228121
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage Refer to TM-175, "Inspection".
1: Bracket
A: Bolt
B : Self-sealing bolt
JSDIA1845ZZ
: Vehicle front
: Oil pan mounting bolt
: Vehicle front
JSDIA1591ZZ
JSDIA1592GB
SCIA5199E
Revision: 2010 May2011 QX56