2011 INFINITI QX56 atf

TM-100
< BASIC INSPECTION >[7AT: RE7R01B]
STALL TEST
STALL TEST
Inspection and JudgmentINFOID:0000000006226793
INSPECTION
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle
so that the A/T fluid temperature is 50 to 80°C (122 to
176 °F). Inspect the amount of AT F. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Start the engine, apply foot brake, and place selector lever in “D” position.
5. Gradually press down the accelerator pedal while holding down the foot brake.
6. Quickly read off the stall speed, and quickly release the accelerator pedal. CAUTION:
Never hold down the accelerator pedal for more than 5 seconds during this test.
7. Shift the selector lever to “N” position.
8. Cool down the ATF. CAUTION:
Run the engine at idle for at least 1 minute.
9. Repeat steps 5 through 8 with selector lever in “R” position.
JUDGMENT OF STALL TEST
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
Stall speed : Refer to TM-297, "Stall Speed".
Selector lever position
Possible location of malfunction
“D” and “M” “R”
Stal l s pe ed HO
 Low brake
 1st one-way clutch
 2nd one-way clutch
OH  Reverse brake
 1st one-way clutch
 2nd one-way clutch
L L  Engine and torque converter one-way clutch
H H  Line pressure low
Does not shift-up “D” or “M” position 1 → 2 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 2 → 3 Slipping in 3GR, 4GR or 5GR Direct clutch slippage
Does not shift-up “D” or “M” position 3 → 4 Slipping in 4GR, 5GR, 6GR or 7GR High and low reverse clutch slippage
Does not shift-up “D” or “M” position 4 → 5 Slipping in 5GR, 6GR or 7GR Input clutch slippage
Does not shift-up “D” or “M” position 5 → 6 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 6 → 7 Slipping in 7GR Front brake slippage
Revision: 2010 May2011 QX56

TM-114
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0729 6GR INCORRECT RATIO
P0729 6GR INCORRECT RATIO
DescriptionINFOID:0000000006226815
This malfunction is detected when the A/T does not shift
into 6GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226816
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-115, "
Diagnosis Procedure"” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “6TH GR FNCTN P0729” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0729 Gear 6 Incorrect Ratio The gear ratio is:
 0.915 or more
 0.813 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-118
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0731 1GR INCORRECT RATIO
P0731 1GR INCORRECT RATIO
DescriptionINFOID:0000000006226821
This malfunction is detected when the A/T does not shift
into 1GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226822
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-119, "
Diagnosis Procedure"” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “1ST GR FNCTN P0731” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0731 Gear 1 Incorrect Ratio The gear ratio is:
 5.180 or more
 4.594 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-120
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0732 2GR INCORRECT RATIO
P0732 2GR INCORRECT RATIO
DescriptionINFOID:0000000006226824
This malfunction is detected when the A/T does not shift
into 2GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226825
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-121, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “2ND GR FNCTN P0732” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0732 Gear 2 Incorrect Ratio The gear ratio is:
 3.360 or more
 2.980 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-122
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0733 3GR INCORRECT RATIO
P0733 3GR INCORRECT RATIO
DescriptionINFOID:0000000006226827
This malfunction is detected when the A/T does not shift
into 3GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226828
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-123, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “3RD GR FNCTN P0733” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0733 Gear 3 Incorrect Ratio The gear ratio is:
 2.148 or more
 1.906 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-124
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0734 4GR INCORRECT RATIO
P0734 4GR INCORRECT RATIO
DescriptionINFOID:0000000006226830
This malfunction is detected when the A/T does not shift
into 4GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226831
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-125, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “4TH GR FNCTN P0734” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0734 Gear 4 Incorrect Ratio The gear ratio is:
 1.496 or more
 1.328 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-126
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0735 5GR INCORRECT RATIO
P0735 5GR INCORRECT RATIO
DescriptionINFOID:0000000006226833
This malfunction is detected when the A/T does not shift
into 5GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226834
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-127, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “5TH GR FNCTN P0735” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0735 Gear 5 Incorrect Circuit The gear ratio is:
 1.060 or more
 0.940 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-142
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P1734 7GR INCORRECT RATIO
P1734 7GR INCORRECT RATIO
DescriptionINFOID:0000000006226861
This malfunction is detected when the A/T does not shift
into 7GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226862
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-143, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “7TH GR FNCTN P1734” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P1734 Gear 7 Incorrect Ratio The gear ratio is:
 0.821 or more
 0.729 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56