2011 INFINITI QX56 washer fluid

FLUID COOLER SYSTEMTM-203
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
10. Remove control cable mounting bracket. Refer to TM-178, "Removal and Installation".
11. Remove front under cover. Refer to EXT-25, "
Removal and Installation".
12. Remove A/T fluid cooler hoses and A/T fluid cooler tubes. CAUTION:
Be careful not to bend A/T fluid cooler tubes.
NOTE:
Cap or plug openings to prevent fluid from spilling.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Never reuse copper washers.
 Be careful not to damage A/T fluid cooler core.
 Be careful not to damage condenser co re, condenser pipe and liquid tank.
 Refer to the following when installing A/T fluid cooler hoses.
*: Refer to the illustrations for the specific position each hose clamp tab.
- The illustrations indicate the view from the hose ends.
- When installing hose clamps center line of each hose clamp tab should be positioned as shown in the figure.
- Insert A/T fluid cooler hoses according to dimension “L” described below.
Hose name Hose end Paint mark Position of hose clamp*
A/T fluid cooler hose AA/T fluid cooler tube A side Facing upward A
A/T fluid warmer side Facing upward C
A/T fluid cooler hose B A/T fluid warmer side Facing leftward E
A/T fluid cooler tube B side Facing downward B
A/T fluid cooler hose C A/T fluid cooler tube B side Facing rightward G
A/T fluid cooler side Facing upward F
A/T fluid cooler hose D A/T fluid cooler side — C
A/T fluid cooler tube C side — G
A/T fluid cooler hose E A/T fluid cooler tube C side Facing downward B
A/T fluid cooler tube D side Facing rightward D
H
: Vehicle upper
I : Vehicle front
JSDIA1639ZZ
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-207
< UNIT REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
 When installing A/T assembly to the engine, be sure to check dimension “A” to ensure it is within the reference value limit.
 When installing A/T assembly to the engine, attach the fixing bolts in accordance with the following standard.
*: Tightening the bolt with bracket (and washer). Refer to TM-199, "2WD : Exploded View".
 Align the positions of tightening bolts for drive plate with those of the torque converter, and temporarily
tighten the bolts. Then, tighten the bolts with the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwise as viewed from the front of the engine.
 When tightening the tightening bolts for the torq ue converter after fixing the crankshaft pulley
bolts, be sure to confirm the tightening torque of the crankshaft pulley mounting bolts. Refer to
EM-62, "
Removal and Installation".
 Rotate crankshaft several turns and check to be sure that A/T rotates freely without binding after
converter is installed to drive plate.
2WD : Inspection and AdjustmentINFOID:0000000006233265
INSPECTION AFTER INSTALLATION
 Check A/T fluid leakage. Refer to TM-175, "Inspection".
 Check A/T position after adjusting A/T position. Refer to TM-101, "
Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Adjust A/T position. Refer to TM-101, "
Adjustment".
 Perform decel G sensor calibration when replacing A/T assembly. Refer to TM-91, "
Special Repair Require-
ment".
4WD
B: Scale
C : Straightedge
Dimension “A” : Refer to TM-297, "Torque Convert-
er".
JPDIA0042ZZ
Bolt symbol A
Insertion direction A/T assembly to engine
Number of bolts 9
Bolt length “L”
mm (in) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb) 113 (12, 83)
JSDIA1598ZZ
Revision: 2010 May2011 QX56

TM-210
< UNIT REMOVAL AND INSTALLATION >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
 When installing A/T assembly to the engine, attach the fixing bolts
in accordance with the following standard.
*: Tightening the bolt with bracket (and washer). Refer to TM-200, "4WD : Exploded View".
 Align the positions of tightening bolts for drive plate with those of the torque converter, and temporarily
tighten the bolts. Then, tighten the bolts with the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwi se as viewed from the front of the engine.
 When tightening the tightening bolts for the torque converter after fixing the crankshaft pulley
bolts, be sure to confirm the tightening torque of the crankshaft pulley mounting bolts. Refer to
EM-62, "
Removal and Installation".
 Rotate crankshaft several turns and check to be sure that A/T rotates freely without binding after
converter is installed to drive plate.
4WD : Inspection and AdjustmentINFOID:0000000006226912
INSPECTION AFTER INSTALLATION
 Check A/T fluid leakage.
 Check A/T position after adjusting A/T position. Refer to TM-101, "
Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Adjust A/T position. Refer to TM-101, "
Inspection".
 Perform decel G sensor calibration w hen replacing A/T assembly. Refer to TM-91, "
Special Repair Require-
ment".
Bolt symbol A
Insertion direction A/T assembly to engine
Number of bolts 9
Bolt length “L”
mm (in) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb) 113 (12, 83)
JSDIA1598ZZ
Revision: 2010 May2011 QX56

WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-15
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
K L
M B A
O P
FR FOG IND
[Off] This item is displayed, but cannot be monitored.
RR FOG IND
[Off] This item is displayed, but cannot be monitored.
LIGHT IND
[On/Off] Status of light indicator lamp detected from position light request signal is received
from BCM via CAN communication.
OIL W/L
[On/Off] Status of oil pressure warning lamp detected from oil pressure switch signal is re-
ceived from BCM via CAN communication.
MIL
[On/Off] Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.
GLOW IND
[Off] This item is displayed, but cannot be monitored.
CRUISE IND
[On/Off]  Status of CRUISE indicator detected from ASCD status signal is received from
ECM via CAN communicat ion. (ASCD models)
 Status of CRUISE indicator de tected from meter display signal is received from
ADAS control unit via CAN communication. (ICC models)
SET IND
[On/Off] Status of SET indicator detected from meter display signal is received from ADAS
control unit via CAN communication.
CRUISE W/L
[On/Off] Status of CRUISE warning lamp
judged from ICC warning lamp signal received
from ADAS control unit with CAN communication line.
BA W/L
[On/Off] Status of IBA OFF indicator lamp judged from IBA OFF indicator lamp signal re-
ceived from ADAS control unit with CAN communication line.
ATC/T-AMT W/L
[On/Off] Status of A/T CHECK warning lamp judged
from A/T CHECK indicator lamp signal
received from TCM with CAN communication line.
ATF TEMP W/L
[Off] This item is displayed, but cannot be monitored.
4WD W/L
[On/Off] Status of 4WD warning lamp judged from 4WD warning lamp signal received from
4WD control unit with
CAN communication line.
FUEL W/L
[On/Off] Low-fuel warning lamp status detected by the identified fuel level.
WASHER W/L
[On/Off] Status of low washer fluid warning judged from washer level switch input to com-
bination meter.
AIR PRES W/L
[On/Off] Status of low tire pressure warning lamp judged from low tire pressure warning
lamp signal received from BCM with CAN communication line.
KEY G/Y W/L
[On/Off] Status of KEY warning lamp
(Green/Yellow) detected from KEY warning lamp sig-
nal is received from BCM via CAN communication.
KEY KNOB W/L
[Off] This item is displayed, but cannot be monitored.
AFS OFF IND
[On/Off] Status of AFS OFF indicator lamp judged from AFS OFF indicator lamp signal re-
ceived from AFS control unit with CAN communication line.
DDS
* W/L
[Off] This item is displayed, but cannot be monitored.
LANE W/L
[On/Off] Status of lane departure warning lamp judged from lane departure warning lamp
signal received from ADAS control unit with CAN communication line.
LDP IND
[On/Off] Status of LDP ON indicator lamp judged from LDP ON indicator lamp signal re-
ceived from ADAS control unit with CAN communication line.
AT P W / L
[On/Off] Status of ATP warning lamp judged from ATP warning lamp signal received from
4WD control unit with
CAN communication line.
DCA IND
[Off] This item is displayed, but cannot be monitored.
CHECK SUS IND
[On/Off] Status of CK SUSP indicator lamp judged from CK SUSP indicator lamp signal re-
ceived from E-SUS control unit with CAN communication line.
Display item [Unit]
MAIN
SIGNALS Description
Revision: 2010 May2011 QX56

WCS-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
4WD W/L Lighting history of 4WD warning lamp.
FUEL W/L Lighting history of low fuel level warning.
WASHER W/L Lighting history of low washer fluid warning.
AIR PRES W/L Lighting history of low tire pressure warning lamp.
KEY G/Y W/L Lighting history of KEY warning lamp.
KEY R W/L This item is displayed, but cannot be monitored.
KEY KNOB W/L This item is displa yed, but cannot be monitored.
EPS W/L This item is displayed, but cannot be monitored.
e-4WD This item is displayed, but cannot be monitored.
AFS OFF IND This item is displayed, but cannot be monitored.
4WAS/RAS W/L This item is displayed, but cannot be monitored.
HDC W/L This item is displayed, but cannot be monitored.
SYS FAIL W/L This item is displa yed, but cannot be monitored.
SFT POSI W/L This item is displayed, but cannot be monitored.
HV BAT W/L This item is displayed, but cannot be monitored.
HEV BRAKE W/L This item is displayed, but cannot be monitored.
SFT OPER W/L This item is displayed, but cannot be monitored.
LANE W/L Lighting history of lane departure warning lamp.
CHAGE W/L This item is displayed, but cannot be monitored.
OIL LEV LOW This item is displayed, but cannot be monitored.
DPF W/L This item is displayed, but cannot be monitored.
TRAILER IND This item is displayed, but cannot be monitored.
RUN FLAT W/L This item is displa yed, but cannot be monitored.
E-SUS W/L This item is displayed, but cannot be monitored.
LAUNCH CNT W/L This item is displayed, but cannot be monitored.
BRAKE PAD W/L This item is displa yed, but cannot be monitored.
Display item Description
Revision: 2010 May2011 QX56

WCS
COMBINATION METERWCS-23
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P
LIGHT IND Ignition switch
ONTail lamp indicator lamp ON On
Tail lamp indicator lamp OFF Off
OIL W/L Ignition switch
ONOil pressure warning lamp ON On
Oil pressure warning lamp OFF Off
MIL Ignition switch
ONMalfunction indicator lamp ON On
Malfunction indicator lamp OFF Off
GLOW IND Ignition switch
ONNOTE:
This item is displayed, but cannot be moni-
tored.
Off
CRUISE IND Ignition switch
ONCRUISE indicator ON On
CRUISE indicator OFF Off
SET IND Ignition switch
ONSET indicator ON On
SET indicator OFF Off
CRUISE W/L Ignition switch
ONCRUISE warning lamp ON On
CRUISE warning lamp OFF Off
BA W/L Ignition switch
ONIBA OFF indicator lamp ON On
IBA OFF indicator lamp OFF Off
AT C / T - A M T W / L Ignition switch
ONA/T check warning lamp ON On
A/T check warning lamp OFF Off
ATF TEMP W/L Ignition switch
ONNOTE:
This item is displayed, but cannot be moni-
tored.
Off
4WD W/L Ignition switch
ON4WD warning lamp ON On
4WD warning lamp OFF Off
FUEL W/L Ignition switch
ONDuring low fuel warning indication On
Other than the above Off
WASHER W/L Ignition switch
ONDuring low washer fluid warning indication On
Other than the above Off
AIR PRES W/L Ignition switch
ONLow tire pressure
warning lamp ON On
Low tire pressure warning lamp OFF Off
KEY G/Y W/L Ignition switch
ONKEY warning lamp (G
reen/Yellow) ON On
KEY warning lamp (G reen/Yellow) OFF Off
KEY KNOB W/L Ignition switch
ONNOTE:
This item is displayed, but cannot be moni-
tored.
Off
AFS OFF IND Ignition switch
ONAFS OFF indicator lamp ON On
AFS OFF indicator lamp OFF Off
DDS W/L Ignition switch
ONNOTE:
This item is displayed, but cannot be moni-
tored.
Off
LANE W/L Ignition switch
ONLane departure warning lamp ON On
Lane departure warning lamp OFF Off
LDP IND Ignition switch
ONLDP ON indicator lamp ON On
LDP ON indicator lamp OFF Off
AT P W / L Ignition switch
ONATP warning lamp ON On
AT P w a r n i n g l a m p O F F O f f
Monitor Item Condition Value/Status
Revision: 2010 May2011 QX56

WW-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Component Description
INFOID:0000000006300449
Washer SwitchINFOID:0000000006300450
 Washer switch is integrated combination switch.
 Combination switch switches polarity between front washer operating and rear washer operating to supply
power to the washer pump on ground.
Part Description
IPDM E/R  Controls the integrated relay according to the request (via CAN communication) from BCM.
 Performs the auto stop control of the front wiper.
BCM  Judges the each switch status by the combination switch reading function.
 Requests (via CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
 Supplies power to the rear wiper motor.
 Performs the auto stop control of the rear wiper.
 Requests (via CAN communication) the headlamp washer relay ON to IPDM I/R.
TCM Transmits the shift position signal to BCM via CAN communication.
Light & rain sensor Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal
to BCM via the rain sensor serial link.
Combination switch
(Wiper & washer switch) Refer to
BCS-7, "
COMBINATION SWITCH READING S YSTEM : System Description".
Washer switch Refer to WW-6, "
Washer Switch".
Washer pump  Washer fluid is sprayed according to washer switch states.
 Switching between front washer and rear washer is performed according to the voltage polarity
change to washer pomp.
Headlamp washer pump Washer fluid is sprayed according to washer switch states and headlamp switch status.
Front wiper motor  IPDM E/R controls front wiper operation.
 Front wiper auto stop signal is transmitted to IPDM E/R.
Rear wiper motor  BCM controls rear wiper operation.
 Rear wiper auto stop signal is transmitted to BCM.
Combination meter Transmits the vehicle speed signal to BCM via CAN communication.
JPLIA0163GB
Revision: 2010 May2011 QX56

SYSTEMWW-7
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K
M A
B
WW
N
O P
SYSTEM
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM : System DiagramINFOID:0000000006300451
FRONT WIPER AND WASHER S YSTEM : System DescriptionINFOID:0000000006300452
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
 Combination switch reading function
 Front wiper control function
Control by IPDM E/R
 Front wiper control function
 Relay control function
Combination meter indicates low washer fluid level warning judged by the signal from the washer level switch.
For details of low washer fluid level warning, refer to MWI-16, "
MASTER WARNING LAMP : System Descrip-
tion".
FRONT WIPER BASIC OPERATION
 BCM detects the combination switch condition by the combination switch reading function.
 BCM transmits the front wiper request signal to IPDM E/R via CAN communication depending on each oper-
ating condition of the front wiper.
 IPDM E/R turns ON/OFF the integrated front wiper rela y and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
 BCM transmits the front wiper request signal (LO) to IPDM E/R via CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
 IPDM E/R turns ON the integrated front wiper rela y according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
 BCM transmits the front wiper request signal (HI) to IPDM E/R via CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
 IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
JPLIA1630GB
Revision: 2010 May2011 QX56