2011 INFINITI QX56 stop start

TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion
trouble
Gear
does no
change “D” position Locks in 1GR 1 1 1 1
Locks in 2GR
Locks in 3GR
Locks in 4GR
Locks in 5GR 1
Locks in 6GR
Locks in 7GR
1GR
→ 2GR 1 1 1 1
2GR → 3GR 1
3GR → 4GR 2 22 2222 1
4GR → 5GR 1 1
5GR → 6GR 1
6GR → 7GR 1 1 1 1 1
5GR → 4GR 1
4GR → 3GR 1 1 1
3GR → 2GR 1 1
2GR → 1GR 1 1 1
Does not lock-up 2 22245 32222222 2 2 1
“M” posi-
tion 1GR
⇔ 2GR 3 33 32 3333333 3 3 1
2GR ⇔ 3GR 3 33 32 3333333 3 3 1
3GR ⇔ 4GR 3 33 32 3333333 3 3 1
4GR ⇔ 5GR 3 33 32 3333333 3 3 1
5GR ⇔ 6GR 3 33 32 3333333 3 3 1
6GR ⇔ 7GR 3 33 32 3333333 3 3 1
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion trou-
ble
Poor
shiftingSlip
When
shifting
gears1GR
⇔ 2GR 3 3 3 4 2 2 1
2GR ⇔ 3GR 3 3 3 4 2 2 1
3GR ⇔ 4GR 3 3 3 4 2 2 2 2 1
4GR ⇔ 5GR 3 3 3 4 2 2 2 1
5GR ⇔ 6GR 3 3 3 4 2 2 2 1
6GR ⇔ 7GR 3 3 3 4 2 2 2 1
Engine
brake
does
not
work “D” position
→ “M” posi-
tion 5556423 33 1
“M” po-
sition 7GR
→ 6GR 5 5 5 6 4 2 3 3 3 1
6GR → 5GR 5 5 5 6 4 2 3 3 3 1
5GR → 4GR 5 5 5 6 4 2 3 3 3 1
4GR → 3GR 5 5 5 6 4 2 3 3 3 3 1
3GR → 2GR 5 556423 33 1
2GR → 1GR 5 5 5 6 4 2 3 3 3 1
Revision: 2010 May2011 QX56

TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2 2 2 1
With selector
lever in “R”
position, ac-
celeration is
extremely
poor. 53 334 2 2 2 1
While starting
off by acceler-
ating in 1GR,
engine races. 3 334 2 2 2 1
While acceler-
ating in 2GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 3GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 4GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 5GR,
engine races. 3 334 2 222 2 1
While acceler-
ating in 6GR,
engine races. 3 334 2 22221
While acceler-
ating in 7GR,
engine races. 3 334 2 2 22 2 1
Lock-up 3 334 2 2 1
No creep at
all. 111111111
Extremely
large creep. 1
Symptom
Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Function
trouble
Power transmis-
sion cannot be
performed Vehicle cannot run in all
position.
3 2 111111111
Driving is not possible in
“D” position. 3 2 111111111
Driving is not possible in
“R” position. 32111
Engine stall 4 5 5 6 3 2 1
Engine stalls when selec-
tor lever shifted “N” → “D”
or “R”. 455 3 2 1
Engine does not start in
“N” or “P” position. 312 1
Engine starts in position
other than “N” or “P”. 32 1
Poor operation Vehicle does not enter
parking condition.
12
Parking condition is not
cancelled. 12
Vehicle runs with A/T in
“P” position. 12
Vehicle moves forward
with the “R” position. 12
Vehicle runs with A/T in
“N” position. 12
Vehicle moves backward
with the “D” position. 12
Revision: 2010 May2011 QX56

WT-10
< SYSTEM DESCRIPTION >
SYSTEM
*: Mainly used for the tire inflation indicator function.
LOW TIRE PRESSURE WARNING LAMP CONTROL CONDITION
Uses CAN communication from the low tire pressure warning control unit to illuminate the low tire pressure
warning lamp on the combination meter.
*: Tire pressure at each condition differs.
HAZARD WARNING LAMP CONTROL CONDITION
The low tire pressure warning control unit transmits a hazard request signal to BCM. BCM blinks the hazard
warning lamp, according to the signal.
The hazard warning lamp blinks under the following conditions.
Condition of Blinking The Hazard Warning Lamp When wake-up of registered wheel has been completed. Refer to WT-28, "Work Procedure".
 When ID registration is completed. Refer to WT-29, "
Work Procedure".
 During the use of the tire inflation indicator function.
HORN CONTROL CONDITION
The low tire pressure warning control unit transmits a horn request signal to BCM. BCM controls horn sound,
according to the signal.
The horn sounds under the following condition.
Condition of Sounding Horn During the use of tire inflation indicator function.
Tire Inflation Indicator FunctionINFOID:0000000006225495
 This function operates only when the A/T shift selector position is in P-range with the ignition switch ON or
with the engine started.
NOTE:
The tire inflation indicator function is recommended to use with the engine stopped.
 This function informs the driver of the satisfaction of the recom- mended COLD tire pressure.
The hazard warning lamp blinks when reaching the recommended
COLD tire pressure during radio wave reception. After reaching the
recommended COLD tire pressure, the horn sounds once and the
hazard warning lamp stops blinking.
 When tire pressure becomes a value equal to or more than 30 kPa
(0.31 kg/cm
2, 4 psi) more than the recommended COLD tire pres-
sure, the hazard warning lamp and the horn operates three times.
After deflating the tire and reaching the recommended COLD tire
pressure, the horn sounds only once and the hazard warning lamp
stops blinking.
NOTE:
 After starting to inflate the tire, it takes a few seconds for the tire inflation indicator to function.
ABS actuator and electric unit (con-
trol unit) Transmits the vehicle speed signal (ABS) via CAN communication for low tire pressure warning
control unit.
TCM
*Transmits the P range signal via CAN communication for low tire pressure warning control unit.
Component parts Signal item
Condition Low tire pr
essure warning lamp
Ignition switch: OFF OFF
Ignition switch: ON (System normal) Warning lamp turns on for 1second, then turns OFF.
When tire pressure is low*.
[Less than 189 kPa (1.93 kg/cm
2, 27.4 psi)] ON
Tire pressure monitoring system malfunction Warning lamp blinks 1 minute, then turns ON.
When performing transmitter wake-up operation Refer to WT-28, "
Work Procedure".
JSEIA0214GB
Revision: 2010 May2011 QX56

WT-14
< ECU DIAGNOSIS INFORMATION >
LOW TIRE PRESSURE WARNING CONTROL UNIT
ECU DIAGNOSIS INFORMATION
LOW TIRE PRESSURE WARNING CONTROL UNIT
Reference ValueINFOID:0000000006225497
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The reference values in the table below come from the control unit calculation data. The normal values
may in some cases be displayed even though the power circuit (harness) is open or shorted.
TERMINAL LAYOUT
PHYSICAL VALUES
CAUTION:
When using circuit tester to measure voltage for in spection, be sure not to extend forcibly any con-
nector terminals.
Monitor item Condition Value/Status
VHCL SPEED SE Vehicle stopped 0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition. Approx. equal to the indication
on speedometer (Inside of
±
10%)
AIR PRESS FL Start engine and drive at 40 km/h (25 MPH) or more for 10 minutes. Approximately equal to the indi-
cation on tire gauge value for
front LH tire
AIR PRESS FR Start engine and drive at 40 km/h (25 MPH) or more for 10 minutes. Approximately equal to the indi-
cation on tire gauge value for
front RH tire
AIR PRESS RR Start engine and drive at 40 km/h (25 MPH) or more for 10 minutes. Approximately equal to the indi-
cation on tire gauge value for
rear RH tire
AIR PRESS RL Start engine and drive at 40 km/h (25 MPH) or more for 10 minutes. Approximately equal to the indi-
cation on tire gauge value for
rear LH tire
ID REGST FL1 Front LH transmitter ID registered Done
Front LH transmitter ID unregistered Yet
ID REGST FR1 Front RH transmitter ID registered Done
Front RH transmitter ID unregistered Yet
ID REGST RR1 Rear RH transmitter ID registered Done
Rear RH transmitter ID unregistered Yet
ID REGST RL1 Rear LH transmitter ID registered Done
Rear LH transmitter ID unregistered Yet
WARNING LAMP Low tire pressure
warning lamp: ON On
Low tire pressure warning lamp: OFF Off
JSEIA0024ZZ
Revision: 2010 May2011 QX56

WT-26
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
NO >> GO TO 8.
7.DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Perform the diagnosis applicable to the displayed DTC. Refer to WT-18, "
DTC Index".
>> GO TO 10.
8.CRUISE FOR SYMPTOM CHECK
1. Start the engine.
2. Drive for several minutes at a speed of 40 km /h (25 MPH) or more, then stop the vehicle.
>> GO TO 9.
9.PERFORM DIAGNOSIS BY SYMPTOM
Perform trouble diagnosis or repair applicable to the symptom. Refer to WT-53, "
Symptom Table".
>> GO TO 11.
10.FINAL CHECK (WHEN DTC WAS DETECTED)
With CONSULT-III
Perform “DTC CONFIRMATION PROCE DURE” (self-diagnosis) with applicable DTC.
Is any malfunction detec ted by self-diagnosis?
YES >> GO TO 7.
NO >> INSPECTION END
11 .FINAL CHECK (WHEN SYMPTOM OCCURRED)
Make sure that the symptom is not detected.
Does symptom remain?
YES >> GO TO 9.
NO >> INSPECTION END
Revision: 2010 May2011 QX56

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-31
< DTC/CIRCUIT DIAGNOSIS >
C
D F
G H
I
J
K L
M A
B
WT
N
O P
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC LogicINFOID:0000000006225508
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION
With CONSULT-III
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to WT-69, "
Tire Air Pres-
sure".
3. Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC
“C1704”, “C1705”, “C1706”, or “C1707” detected?
YES >> Proceed to WT-31, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006225509
1.CHECK TIRE PRESSURE
Check the air pressure of all wheels. Refer to WT-69, "
Tire Air Pressure".
Is the inspection result normal?
YES >> Replace the DTC-detected malfunctioning transmitter. Refer to WT-66, "Removal and Installa-
tion".
NO >> After adjusting the air pressure, GO TO 2.
2.CHECK TIRE PRESSURE SIGNAL
With CONSULT-III
1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2. Stop the vehicle.
3. Select “DATA MONITOR” for “AIR PRESSURE MONITOR” with CONSULT-III.
4. Within 5 minutes after vehicle stopped, check t hat the tire pressures match the standard value.
Is the inspection result normal?
YES >> INSPECTION END
DTC Display Item Malfunction detected condition Possible causes
C1704 LOW PRESSURE FL Front LH wheel pressure drops to 189 kPa (1.93 kg/cm
2, 27.4 psi)
or less
Low tire pressure
C1705 LOW PRESSURE FR
Front RH wheel pressure drops to 189 kPa (1.93 kg/cm
2, 27.4 psi)
or less
C1706 LOW PRESSURE RR Rear RH wheel pressure drops to 189 kPa (1.93 kg/cm
2, 27.4 psi)
or less
C1707 LOW PRESSURE RL Rear LH wheel pressure drops to 189 kPa (1.93 kg/cm
2, 27.4 psi) or
less
Monitor item Displayed value
AIR PRESS FL Approximately equal to the indication on tire gauge value for front LH tire
AIR PRESS FR Approximately equal to the indication on tire gauge value for front RH tire
AIR PRESS RR Approximately equal to the indica tion on tire gauge value for rear RH tire
AIR PRESS RL Approximately equal to the indication on tire gauge value for rear LH tire
Revision: 2010 May2011 QX56