2011 INFINITI QX56 ABS

DAS
C1A13 STOP LAMP RELAYDAS-145
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
Is the inspection result normal?
YES >> GO TO 21.
NO >> GO TO 17.
17.CHECK STOP LAMP SWITCH INSTALLATION
1. Turn ignition switch OFF.
2. Check stop lamp switch for correct installation. Refer to BR-7, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 18.
NO >> Adjust stop lamp switch installation. Refer to BR-7, "
Inspection and Adjustment".
18.CHECK STOP LAMP SWITCH
1. Disconnect stop lamp switch connector.
2. Check stop lamp switch. Refer to DAS-137, "
Component Inspection (Stop Lamp Switch)".
Is the inspection result normal?
YES >> GO TO 19.
NO >> Replace stop lamp switch.
19.CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1. Connect stop lamp switch connector.
2. Check the voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 20.
NO >> Repair or replace stop lamp switch power supply circuit.
20.CHECK HARNESS BETWEEN STOP LAMP SWITCH AND ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT)
1. Turn the ignition switch OFF.
2. Disconnect stop lamp switch, ABS actuator and electric unit (control unit) connectors.
3. Check for continuity between the stop lamp swit ch harness connector and the ABS actuator and electric
unit (control unit) harness connector.
4. Check for continuity between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 21.
NO >> Repair the harnesses or connectors.
21.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect all connectors again if the connectors are disconnected.
Te r m i n a l
Voltag e
(Approx.)
(+) (–)
Stop lamp switch
Ground
Connector Terminal
E115 3 Battery
voltage
Stop lamp switch ABS actuator and electric
unit (control unit) Continuity
Connector Terminal Connector Terminal
E115 4 E36 17 Existed
Stop lamp switch GroundContinuity
Connector Terminal
E115 4 Not existed
Revision: 2010 May2011 QX56

DAS-146
< DTC/CIRCUIT DIAGNOSIS >[DCA]
C1A13 STOP LAMP RELAY
2. Turn ignition switch ON.
3. Perform “All DTC Reading”.
4. Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”. Refer to
EC-98, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part s identified by the self-diagnosis result.
NO >> GO TO 22.
22.PERFORM SELF-DIAGNOSIS OF ABS ACTUAT OR AND ELECTRIC UNIT (CONTROL UNIT)
1. Connect all connectors again if the connectors are disconnected.
2. Turn ignition switch ON.
3. Perform “All DTC Reading”.
4. Check if any DTC is detected in “Self Diagnostic Result” of “ABS”. Refer to BRC-51, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part s identified by the self-diagnosis result.
NO >> Replace ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Component InspectionINFOID:0000000006228078
1.CHECK ICC BRAKE HOLD RELAY
Apply battery voltage to ICC brake hold relay terminals 1 and 2, and
then check for continuity under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace ICC brake hold relay.
Terminal Condition Continuity
35 When the battery voltage is applied Existed
When the battery voltage is not ap-
plied
Not exist-
ed
JSOIA0075GB
Revision: 2010 May2011 QX56

DAS-148
< DTC/CIRCUIT DIAGNOSIS >[DCA]
C1A15 GEAR POSITION
C1A15 GEAR POSITION
DescriptionINFOID:0000000006228081
ADAS control unit judges the gear pos
ition based on the following signals.
 Current gear position signal transmitt ed from TCM via CAN communication.
 Value of gear ratio calculated from input speed signal transmitted from TCM via CAN communication.
 Value of gear ratio calculated from the vehicle speed signal transmitted from ABS actuator and electric unit
(control unit) via CAN communication.
DTC LogicINFOID:0000000006228082
DTC DETECTION LOGIC
NOTE:
If DTC “C1A15” is detected along with DTC “U1000”, “C1A03”, or “C1A04”, first diagnose the DTC “U1000”,
“C1A03”, or “C1A04”.
 Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic" for DTC “U1000”.
 Refer to DAS-131, "
DTC Logic" for DTC “C1A03”.
 Refer to DAS-133, "
DTC Logic" for DTC “C1A04”.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Drive the vehicle at 10 km/h (6 MPH) or faster for approximately 15 minutes or more.
CAUTION:
Always drive safely.
4. Stop the vehicle.
5. Perform “All DTC Reading” with CONSULT-III.
6. Check if “C1A15” is detected as the current malf unction in the “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A15” detected as the current malfunction?
YES >> Refer to DAS-148, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228083
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “C1A03”, “C1A04”, or “U1000” is detected ot her than “C1A15” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-100, "
DTC Index".
NO >> GO TO 2.
2.CHECK VEHICLE SPEED SIGNAL
Check that “VHCL SPEED SE” operates norma lly in “DATA MONITOR” of “ICC/ADAS”.
CAUTION:
Be careful of the vehicle speed.
Is the inspection result normal?
DTC
(On board dis- play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A15 (15) GEAR POSITION A mismatch between an current gear posi-
tion signal transmitted from TCM via CAN
communication and a gear position calculat-
ed by the ADAS control unit continues for
approximately 11 minutes or more  Input speed sensor
 Vehicle speed sensor A/T (output speed
sensor)
TCM
Revision: 2010 May2011 QX56

DAS
C1A15 GEAR POSITIONDAS-149
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
YES >> GO TO 3.
NO >> GO TO 7.
3.CHECK GEAR POSITION
Check that “GEAR” operates normally in “DATA MONITOR” of “ICC/ADAS”.
CAUTION:
Be careful of the vehicle speed.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK GEAR POSITION SIGNAL
Check that “GEAR” operates normally in “DATA MONITOR” of “TRANSMISSION”.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK INPUT SPEED SENSOR SIGNAL
Check that “INPUT SPEED” operates normally in “DATA MONITOR” of “TRANSMISSION”.
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> GO TO 6.
6.CHECK TCM SELF-DIAGNOSIS RESULTS
1. Perform “All DTC Reading”.
2. Check if any DTC is detected in “Sel f Diagnostic Result” of “TRANSMISSION”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
TM-78, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
7.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
1. Perform “All DTC Reading”.
2. Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Revision: 2010 May2011 QX56

DAS-156
< DTC/CIRCUIT DIAGNOSIS >[DCA]
C1A26 ECD MODE MALFUNCTION
C1A26 ECD MODE MALFUNCTION
DTC LogicINFOID:0000000006228094
DTC DETECTION LOGIC
NOTE:
If DTC “C1A26” is detected along with DTC “U1000”
, “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
 DTC “U1000”: Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0415”: Refer to DAS-180, "
DTC Logic".
 DTC “U0121”: Refer to DAS-175, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Wait for approximately 1 minute after turning the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A26” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A26” detected as the current malfunction?
YES >> Refer to DAS-156, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228095
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A26” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-100, "
DTC Index".
NO >> GO TO 2.
2.PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A26 (26) ECD MODE MALF If an abnormal condition occurs with ECD system ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56

DAS
C1A27 ECD POWER SUPPLY CIRCUITDAS-157
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A27 ECD POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006228096
DTC DETECTION LOGIC
NOTE:
If DTC “C1A27” is detected along with DTC “U1000” , “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
 DTC “U1000”: Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
 DTC “U0415”: Refer to DAS-180, "
DTC Logic".
 DTC “U0121”: Refer to DAS-175, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Wait for approximately 1 minute af ter turning the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A27” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A27” detected as the current malfunction?
YES >> Refer to DAS-157, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228097
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A27” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-100, "
DTC Index".
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT OF ABS ACTU ATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check power supply circuit of ABS actuator and electric unit (control unit). Refer to BRC-113, "
Diagnosis Pro-
cedure".
Is the inspection result normal?
YES >> Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to BRC-51, "DTC
Index".
NO >> Repair the harnesses or connectors.
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A27 (27) ECD PWR SUPLY CIR ECD system power supply voltage is excessively
low  ABS actuator and el
ectric unit (con-
trol unit) power supply circuit
 ABS actuator and el ectric unit (con-
trol unit)
Revision: 2010 May2011 QX56

DAS
C1A39 STEERING ANGLE SENSORDAS-165
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A39 STEERING ANGLE SENSOR
DTC LogicINFOID:0000000006228117
DTC DETECTION LOGIC
NOTE:
If DTC “C1A39” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A39” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS”.
Is
“C1A39” detected as the current malfunction?
YES >> Refer to DAS-165, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228118
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A39” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
C1A39 (39) STRG SEN CIR If the steering angle sensor is malfunction Steering angle sensor
Revision: 2010 May2011 QX56

DAS
U0121 VDC CAN 2DAS-175
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U0121 VDC CAN 2
DTC LogicINFOID:0000000006228131
DTC DETECTION LOGIC
NOTE:
If DTC “U0121” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0121” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0121” detected as the current malfunction?
YES >> Refer to DAS-175, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228132
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0121” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0121 (127) VDC CAN CIR2 If ADAS control unit detects an error signal
that is received from
ABS actuator and electric
unit (control unit) via CAN communication ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56